Cordelia Lighting CLED1011A-06 Installation guide

Type
Installation guide

This manual is also suitable for

Questions, problems, missing parts? Before returning to the store,
call Envirolite Customer Service
8 a.m. 6 p.m., EST, Monday Friday
1-800-345-0542
CLED1011A-06
LED CEILING FLUSH MOUNT
SAFETY INFORMATION
Before starting installation of this
fixture or removal of a previous
fixture, disconnect the power by
turning off the circuit breaker or by
removing the fuse at the fuse box.
Consult a qualified electrician if you have any electrical questions or need to
replace the driver.
If you have any non-electrical questions about this fixture, please contact our
Customer Service Team at 1-800-345-0542.
WARNING: Disconnect the
power prior to removing or
installing a light fixture.
PLANNING THE INSTALLATION
NOTE: Keep your receipt and
these instructions for Proof of
Purchase.
Read all instructions before assembly and installation. Before starting installation
of the fixture or removal of a previous fixture, disconnect the power by turning off
the circuit breaker or by removing the fuse at the fuse box. To avoid damaging
this product, assemble it on a soft, non-abrasive surface such as carpet or
cardboard.
TOOLS REQUIRED
2
Phillips
Screwdriver
Wire
Cutter
Wire
Stripper
Ladder
Safety
Goggles
Electrical
Tape
3
Part
Description
Quantity
AA
Acrylic Shade
1
BB
Fixture Pan
1
CC
Hex Nut
1
DD
Wire Nut
3
EE
Thumb Nut
1
FF
Washer
1
GG
Mounting Screw
2
HH
Nipple
1
II
Quick Connector
1
JJ
Mounting Bracket
1
PACKAGE CONTENTS (not to scale)
AA
BB
EE
JJ II
HH GG FF
CC DD
INSTALLATION
Insert the quick connector (II) into
the back of the fixture pan (BB).
Attach the black supply wire to the
black quick connector (II) wire using
a wire nut (DD).
Attach the white supply wire to the
white quick connector (II) wire using
a wire nut (DD).
Connect the fixture ground wire and
the supply ground wire together
using a wire nut (DD).
Wrap all wire connections with
electrical tape for a more secure
connection.
Carefully tuck all the wires and wire
connections into the outlet box.
Align the fixture pan (BB) over the
outlet box and feed the mounting
screws (GG) through the holes on
the fixture pan (BB) and into the
outlet box.
Tighten the mounting screws (GG)
so that the fixture pan (BB) is
secured flush against the ceiling.
1A
2A
4
NOTE: If you have electrical
questions consult your local
electrical code for approved
grounding methods.
II
DD
BB
BB
GG
INSTALLATION (continued)
3A
Slide the acrylic shade (AA) onto
the fixture pan (BB) and turn it
clockwise until secure.
1B
Slide the acrylic shade (AA) onto
the fixture pan (BB) and turn it
clockwise until secure.
5
AA
BB
CC
JJ
GG
HH
INSTALLATION (continued)
2B
Insert the quick connector (II) into
the back of the fixture pan (BB).
Attach the black supply wire to the
black quick connector (II) wire
using a wire nut (DD).
Attach the white supply wire to the
white quick connector (II) wire
using a wire nut (DD).
Connect the fixture ground wire
and the supply ground wire
together using a wire nut (DD).
Wrap all wire connections with
electrical tape for a more secure
connection.
3B
Align the center of the fixture
(BB) over the nipple (HH) and
place a rubber washer (CC) over
the nipple (HH).
Insert and tighten the thumb nut
(FF).
Slide the acrylic shade (AA) onto
the fixture pan (BB) and turn it
clockwise until secure.
6
II
DD
BB
HH
BB
EE
FF
HH
EXTERIOR MAINTENANCE
Use a dry or slightly dampened
clean cloth and wipe the surface
of the fixture.
INTERIOR MAINTENANCE
Disconnect power to the fixture by turning off the circuit breaker or by
removing the fuse at the fuse box.
Use a dry or slightly dampened clean cloth to wipe the interior surface of the
fixture.
NOTE: Do not use any cleaners
with chemicals, solvents, or harsh
abrasives. Use only a dry soft
cloth to dust or wipe carefully.
CARE & CLEANING
7
Turn on power at the circuit breaker or fuse box.
Turn the light switch on to activate the fixture.
OPERATION
TROUBLESHOOTING
Problem
Solution
The
light will not turn on.
Make sure the power supply is on.
Test or replace the switch.
Check the wiring.
The
fuse blows or circuit breaker
trips when light is turned on.
Check the wire connections
WARRANTY
8
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in materials
and workmanship for a period of five (5) years from date of purchase. This
warranty applies only to the original consumer purchaser and only to products
used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that the
product has not been damaged through misuse, abuse, accident, modifications,
alterations, neglect or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been improperly
installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product
as a result of an accident, misuse, abuse, negligence, alteration, or faulty
installation, or any other failure not relating to faulty material or workmanship.
This warranty shall not apply to the finish on any portion of the product, such as
surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty, whether
expressed or implied, of fitness for a particular purpose, other than the warranty
contained herein. The manufacturer specifically disclaims any liability and shall
not be liable for any consequential or incidental loss or damage, including but not
limited to any labor/expense costs involved in the replacement or repair of said
product.
9
FCC NOTICE
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiver antenna.
Increase the separation between the equipment and receiver.
Install the product onto on a circuit different from that to which the receiver is
connected.
Consult with the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes made to the electronics circuit will void this equipment’s
compliance with Part 15 of the FCC Rules and should not be operated.
_____________________________
Conforms to standard CAN-ICES 005(B) / NMB-005 (B)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27

Cordelia Lighting CLED1011A-06 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI