American Standard 7144.803 User manual

American Standard
Brand
American Standard
Model
7144.803
Type
User manual

This manual is also suitable for

G49
© 2008 AS America Inc.
DOUBLE BOWL KITCHEN SINK
• Acid-resisting enameled steel
• Double bowl design
• Top mount installation
• Available in 3 or 4 faucet hole congurations
• Silicone sealant supplied
Top Mount:
❏ 7144.803 3-Hole
❏ 7144.804 4-Hole
Nominal Dimensions:
838 x 559 x 184mm
(33" x 22" x 7-1/4")
Bowl sizes:
359mm (14-1/8") wide
413mm (16-1/4") front to back
178mm (7") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Enameled Steel Plumbing
Fixtures
SINGLE BOWL KITCHEN SINK
• Acid-resisting enameled steel
• Single bowl design
• Acid-resisting glossy porcelain nish
• Top mount installation
• Available in 3 or 4 faucet hole congurations
• Silicone sealant supplied
Top Mount:
❏ 7143.803 3-Hole
❏ 7143.804 4-Hole
Nominal Dimensions:
635 x 559 x 184mm
(25" x 22" x 7-1/4")
Bowl sizes:
552mm (21-3/4") wide
413mm (16-1/4") front to back
178mm (7") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Enameled Steel Plumbing
Fixtures
* See faucet section for available models
To Be Specied:
❏ Color: (specify 208 White Heat or 345 Bisque)
❏ Faucet*: (specify nish)
❏ Basket Strainer: 4331.013 (Chrome only)
❏ Soap Dispenser*: 4503.115 (specify color)
❏ Trap:
Optional Accessories:
❏ Large Wood Cutting Board: 9000.250
❏ Small Wood Cutting Board: 9000.185
❏ Colander For Cutting Board: 8102.100, Color:
❏ Large Colander: 8103.100, Color:
DOUBLE BOWL SINK
SINGLE BOWL SINK
ENAMELED STEEL
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS
Revised 2/08
Enameled Steel Double Bowl Sink
Enameled Steel Single Bowl Sink
G50
© 2008 AS America Inc.
7144.803/804/805 Top Mount
7143.803/804 Undercounter Mount
NOTES:
*
COUNTERTOP CUTOUT 800 x 521mm WITH 19mm RADIUS
(31-1/2" x 20-1/2" WITH 3/4’ RADIUS) AT CORNERS.
STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
12-1/4"
(311mm)
33"
(838mm)
4" (102mm)
4" (102mm)
4" (102mm)
4"
(102mm)
22"
(559mm)
*
CUTOUT
NOTE
2-1/4"
(57mm)
7144.804
4 HOLE
7144.805
5 HOLE
FINISHED WALL OR SPLASH BACK
38mm (1-1/2)
DIA. (TYP.)
OPTIONAL
COUNTER TOP (BY OTHERS)
C/L
15-5/8"
(397mm)
FINISHED
FLOOR
3-1/2"
(89mm)
CLAMPING DETAIL
LUG AND
SCREW
ASSEMBLY
COUNTERTOP
13/16"
(21mm)
MAX.
16-1/2"
(419mm)
1-1/2" O.D. TAILPIECE
36" (914mm)
SUGGESTED
6"
(152mm)
1/2"
(13mm)
6-3/4"
(171mm)
1-1/2"
(38mm) R.
CLAMPING DETAIL
LUG AND
SCREW
ASSEMBLY
COUNTERTOP
12-1/2"
(318mm)
7143.804
4 HOLE
FINISHED WALL OR SPLASH BACK
C/L
OPTIONAL
COUNTER TOP (BY OTHERS)
FINISHED
FLOOR
*
CUTOUT
NOTE
13/16"
(21mm)
MAX.
1-1/2" O.D.
TAILPIECE
36" (914mm)
SUGGESTED
6"
(152mm)
1/2"
(13mm)
6-3/4"
(171mm)
12-1/4"
(311mm)
22"
(559mm)
2-1/4"
(57mm)
3-1/2"
(89mm)
1-1/2"
(38mm) R.
4" (102mm)
4" (102mm)
4" (102mm)
38mm (1-1/2)
DIA. (TYP.)
25"
(635mm)
NOTES:
*
COUNTERTOP CUTOUT 597 x 521mm WITH 19mm RADIUS
(23-1/2" x 20-1/2" WITH 3/4’ RADIUS) AT CORNERS.
●
Recommended minimum countertop thickness:
Wood - 19mm (3/4")
Marble and Solid Surface - 12mm (1/2")
STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
DOUBLE BOWL SINK
SINGLE BOWL SINK
ENAMELED STEEL
Revised 2/08
  • Page 1 1
  • Page 2 2

American Standard 7144.803 User manual

American Standard
Brand
American Standard
Model
7144.803
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents