American Standard 7144.803 User manual

Brand: American Standard

Model: 7144.803

Type: User manual

KS-55

DOUBLE BOWL™ SINK

SINGLE BOWL™ SINK

ENAMELED STEEL

DOUBLE BOWL KITCHEN SINK (shown)

❏ 7144.803 3-Hole

❏ 7144.804 4-Hole

❏ 7144.805 5-Hole

Product Features:

• Acid-resisting enameled steel

• Double bowl design

• Self-rimming installation

• Available in 3, 4 or 5 faucet hole configurations

• Silicone sealant supplied

Nominal Dimensions: 838 x 559 x 184mm

(33" x 22" x 7-1/4")

Bowl sizes:

359mm (14-1/8") wide, 413mm (16-1/4") front

to back, 178mm (7") deep

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• ASME A112.19.4M for Enameled Steel Plumbing

Fixtures

To Be Specified

❏ Color: (specify White Heat,Bone, or Bisque)

❏ Faucet*: (specify finish)

❏ Basket Strainer: 4331.013 (Chrome only)

❏ Soap Dispenser*: 4503.115 (specify color)

❏ Trap:

* See faucet section for additional models available

Revised 8/02

SINGLE BOWL KITCHEN SINK

❏ 7143.803 3-Hole

❏ 7143.804 4-Hole

Product Features:

• Acid-resisting enameled steel

• Single bowl design

• Self-rimming installation

• Available in 3 or 4 faucet hole configurations

• Silicone sealant supplied

Nominal Dimensions: 635 x 559 x 184mm

(25" x 22" x 7-1/4")

Bowl sizes:

552mm (21-3/4") wide, 413mm (16-1/4") front to

back, 178mm (7") deep

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• ASME A112.19.4M for Enameled Steel Plumbing

Fixtures

ROUGHING-IN DIMENSIONS SHOWN ON REVERSE SIDE OF PAGE

KS-56

DOUBLE BOWL™ SINK

SINGLE BOWL™ SINK

ENAMELED STEEL

311mm

(12-1/4)

838mm

(33)

102mm

(4)

102mm

(4)

102mm

(4)

102mm

(4)

559mm

(22)

CUTOUT

NOTE

57mm

(2-1/4)

152mm

(6)

7144.804

4 HOLE

7144.805

5 HOLE

FINISHED WALL OR SPLASH BACK

38mm (1-1/2)

DIA. (TYP.)

38mm R.

(1-1/2)

OPTIONAL

13mm

(1/2)

COUNTER TOP (BY OTHERS)

914mm

(36)

SUGGESTED

1-1/2 O.D. TAILPIECE

171mm

(6-3/4)

C/L

397mm

(15-5/8)

FINISHED

FLOOR

89mm

(3-1/2)

CLAMPING DETAIL

LUG AND

SCREW

ASSEMBLY

COUNTERTOP

21mm

(13/16)

MAX.

419mm

(16-1/2)

NOTES:

COUNTERTOP CUTOUT 800 x 521mm WITH 19mm RADIUS (31-1/2” x 20-1/2” WITH 3/4’

RADIUS) AT CORNERS.

PROVIDE SUITABLE REINFORCEMENT FOR WALL AND COUNTERTOP SUPPORTS.

STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

Important: Dimensions of fixtures are nominal and may vary within the range of tolerances

established by ANSI Standard A112.19.4

These measurements are subject to change or cancellation. No responsibility is assumed for

use of superseded or voided pages.

NOTES:

COUNTERTOP CUTOUT 597 x 521mm WITH 19mm RADIUS (23-1/2” x 20-1/2” WITH 3/4’

RADIUS) AT CORNERS.

PROVIDE SUITABLE REINFORCEMENT FOR WALL AND COUNTERTOP SUPPORTS.

STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

Important: Dimensions of fixtures are nominal and may vary within the range of tolerances

established by ANSI Standard A112.19.4

These measurements are subject to change or cancellation. No responsibility is assumed for use

of superseded or voided pages.

CLAMPING DETAIL

LUG AND

SCREW

ASSEMBLY

COUNTERTOP

21mm

(13/16)

MAX.

311mm

(12-1/4)

635mm

(25)

318mm

(12-1/2)

102mm

(4)

102mm

(4)

559mm

(22)

152mm

(6)

7143.804

4 HOLE

FINISHED WALL OR SPLASH BACK

38mm R.

(1-1/2)

C/L

OPTIONAL

13mm

(1/2)

COUNTER TOP (BY OTHERS)

171mm

(6-3/4)

914mm

(36)

SUGGESTED

1-1/2 O.D.

TAILPIECE

FINISHED

FLOOR

102mm

(4)

57mm

(2-1/4)

38mm (1-1/2)

DIA. (TYP.)

89mm

(3-1/2)

CUTOUT

NOTE

7144.803/804/805

7143.803/804

American Standard 7144.803 User manual

American Standard 7144.803 User manual

American Standard 7144.803 User manual

Related papers

Other documents