American Standard 7160.803, 7160.804, 7160.805, Double Bowl 7160.804 User manual

  • Hello! I am an AI chatbot trained to assist you with the American Standard 7160.803 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
4/98
DOUBLE BOWL
DUAL LEVEL SINK
ENAMELED STEEL
DOUBLE BOWL DUAL LEVEL KITCHEN SINK
• Acid-resisting enameled steel
• Dual level, double bowl design
• Self-rimming installation
• Shown with 4205.660 Silhouette faucet
(not included)
Silicone sealant supplied
• Available in 3, 4, or 5 faucet hole
configuration
7160.803 3 hole
7160.804 4 hole
7160.805 5 hole
Nominal Dimensions: 838 x 559 x 184mm
(33" x 22" x 7-1/4")
Bowl sizes:
Large Bowl: 527mm (20-3/4") wide, 413mm
(16-1/4") front to back 178mm (7") deep
Small Bowl: 187mm (7-3/8") wide, 413mm
(16-1/4") front to back 146mm (5-3/4") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.4M for Enameled Steel Plumbing
Fixtures
© 1998 American Standard Inc.
KSS-014
3/8 O.D.
BENDABLE
TUBING
89mm
(3-1/2)
DIA.
54mm
(2-1/8)
51mm (2)
OPTIONAL
FINISHED WALL
OR SPLASHBACK
206mm
(8-1/8)
311mm
(12-1/4 )
102mm(4)
38mm (1-1/2)
DIA. HOLES TYP.
C/L
133mm
(5-1/4)
267mm
(10-1/2)
432mm
(17)
838mm
(33)
171mm
(6-3/4)
146mm
(5-3/4)
SEALING
COMPOUND
203mm
(8)
146mm
(5-3/4)
X
Y
914mm (36)
SUGGESTED
FINISHED FLOOR
COUNTERTOP
(BY OTHERS)
559mm
(22)
*CUTOUT NOTE
7160.804
4 HOLE
38mm (1-1/2)
RAD. TYP.
1-1/2 O.D. TAILPIECE
COUPLING NUTS
ON FITTING
140mm
(5-1/2)
13mm
(1/2)
7160.805
5 HOLE
102mm
(4)
102mm
(4)
102mm
(4)
CLAMPING DETAIL
LUG AND
SCREW
ASSEMBLY
COUNTERTOP
21mm
(13/16)
MAX.
7160.803
2021.700
4205.241
6270.000
7270.SER.
FAUCET
CERAMIX
RELIANT
TOP MOUNT
BOTTOM MOUNT
HERITAGE
AMARILIS
7160.804
2021.741
4205.217
6279.000
7271.SER.
X
44mm(1-3/4)
95mm(3-3/4)
Y
327mm(12-7/8)
254mm(10)
NOTES:
COUNTERTOP CUTOUT 800 X 521MM WITH 19MM RADIUS (31-1/2 X 20-1/2
WITH 3/4” RAD.) AT CORNERS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP
SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard Z124.6
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided leaflet.
To Be Specified
Color: (specify White Heat or Bone)
Faucet*: (specify finish)
Basket Strainer: 4331.013 (Chrome only)
Soap Dispenser*: 4503.115 (specify color)
Trap:
* See faucet section for additional models available
/