Tools Required 3/8"
5/16”
#10-32 Hex Nut
(E)
(B)
#8-18 x 3/8" Screw
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
1 of 6 6100-0061
(J)
#8-18 x 1/4" Screw
1782-839
(B2)
#8-18 x 1/2" Screw
Adaptable Overhead Storage (Mount to Steel Studs ONLY)
Installation Instructions
Place templates (T) and drill holes
1
#2
A
B
E
F
S-75
G
J2
KB2
J
OSHPD WALL MOUNT
#8 - 9/64
#10 - 13/64”
#12 -15/64”
#8-18 x 1/2" Self-Drilling Screw
(J2)
WARNING! Appropriate screws/bolts
must be used to attach overhead to wall.
fasteners must be used.
WARNING!
Scale 1 : 1
011/2
1/4 1/4
TEMPLATE
3/8”
2”
3/4”
3/8”
3/8”3/8”
2”
3/4”
LEFT END PANEL RIGHT END PANEL
3/8”
2”
3/4”
LEFT END PANEL
3/8”
2”
3/4”
RIGHT END PANEL
13/64"
Drill
#10-24 x 1/2” Self Drilling
Hex Head Screw
(S-75)
H
WOOD STEEL
D
D
D
T
T
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
2 of 6 6100-0061 1782-839
Install top (A) and tighten screws (B)
D
FOR ALL DOORS
B
A
B2
Install support brackets (K)
FOR SLOW CLOSE HINGE
K
A
D
D
2
1
3
2
1
3
Install end panels (D) as shown
Install screws (B)
1/8"
(B)
#8-18 x 3/8" Screw
1/4"
(B2)
#8-18 x 1/2" Screw
FOR SLOW CLOSE HINGE SUPPORT BRACKETS (K)
D
D
B2
B
23
4a 4b
A
OR
#10-32 Hex Nut
(E)
D
D
F
1
3E
2
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
3 of 6 6100-0061 1782-839
Mark hole locations on load bar (G)
5
Drill holes in load bar (G)
6
NOTE: Make sure load bar (G) is
snug/tight to bottom edge of top (A).
Following OSHPD - OPM - 0275 - 13.
G
G
A
A
0.0”
9/64"
Drill
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
4 of 6 6100-0061 1782-839
Locate and drill holes in load bar (G) only, NOT the wall
(X - 2.375")
X
2.375"
G
12"
MAXIMUM
BOTH SIDES
Specic Instructions for Wall Frame Construction
Walls with Gypsum Board, Sheet Rock or Wall Board with
Metal Stud Framing: Minimum 18 gage steel or backing.
Wall mount kit must be attached to metal studs.
Use #12 x 1-1/12” TEKS self-drilling screws.
7
G
NOTE:
Following OSHPD -
OPM - 0275 - 13.
15/64"
Drill
WOOD STEEL
OSHPD - OPM - 0275 - 13
Install OSU (F) Mark and predrill bottom shelf only, NOT the wall
L
9 10
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
5 of 6 6100-0061 1782-839
Install load bar (G)
S-75
8
G
A
0.0”
S-75
S-75
#12 x 1-1/2" Tek Screw Self Drilling
(L)
#12 x 1-1/2" Tek Screw Self Drilling
(L)
F
F
L
G
NOTE:
Following OSHPD -
OPM - 0275 - 13.
NOTE:
Following OSHPD -
OPM - 0275 - 13.
NOTE: Wall must
be notched for
OSU to be level.
15/64"
Drill
#10-24 x 1/2” Self Drilling
Hex Head Screw
(S-75)
G
NOTE: Drill and install sheet metal
screws (S-75) every 8” on-center.
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
6 of 6 6100-0061 1782-839
H
H
(J)
#8-18 x 1/4" Screw
J
LOOSEN
ADJUST
TIGHTEN
Install and adjust door (H) as needed
#8-18 x 1/2" Self-Drilling Screw
(J2)
FOR SLOW CLOSE HINGEFOR STANDARD HINGE
OR
J2
LOOSEN
ADJUST
TIGHTEN
22
3
3
1
1
12a 12b
NOTE: If door (H) is misaligned
from RIGHT to LEFT loosen
screws (J) or (J2) and move the
doors in the direction necessary
for alignment.
S-75
G
A
4” Maximum from end.
8”
#10-24 x 1/2” Self Drilling
Hex Head Screw
(S-75)
9/64"
Drill
Predrill holes and install screws (S-75)
11
/
