B
A
B
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
1 of 5 F
Tools Required
7021-6844217-112
RACE
®
1Remove fabric pad (A) and raceway top cover (B)
#5/16
GLAZED WINDOW
Installation Instructions
NOTE!
Leave protective film on glass until it is being installed.
NOTE!
Pry fabric pad away from
frame at top corners.
2Mark and drill raceway top cover (B)
Lower Channel
(Centered)
#5/16
B
NOTE!
Repeat process for opposite
end of raceway top cover.
3Install lower channel (C) 4Install raceway top cover (B)
C
B
#10 x 3/8" Flat Head Screw
(D )
D
#10-32 T-nut
(E )
E
A
B
B
B
B
C
D
E
F
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
2 of 5 F7021-6844217-112
5Install top channel (F) 6Install foam pads (G)
7Install glass pane (H) into channels (C&F)
G
F
H
D
B
HH
B
D
H
F
F
G
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
3 of 5 F7021-6844217-112
8Remove fabric pad (A) 9
10 Remove fabric pads (A)
TWO-HIGH PAD HEIGHT
NOTE!
If lower pad is also to be replaced
with a window, install lower
window first.
Install lower channel (C) on upper rail (J)
Upper post
rin g s
E
J
#10 x 3/8" Flat Head Screw
(D )
#10-32 T-nut
(E )
FOLLOW STEPS 5, 6, AND 7 TO INSTALL GLASS
NOTE!
Repeat process on opposite end.
WINDOW ABOVE RACE GRID ASSEMBLY
NOTE!
The polybag containing (2) painted
spacers and the (2) #10-32 X 5/8"
flathead screws is only required
where window installation
is above Race grid
assembly.
11 Insert T-nuts (E) at both end of upper rail (J)
J
E
12 Re-install bottom fabric pad (A) and grid assembly
J
E
C
D
E
D
J
C
A
A
A
A
J
E
E
J
C
#10-32 X 2"
Pan Head
Screw
E
J
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
4 of 5 F7021-6844217-112
13 Install spacers (K) under lower channel (C)
#10 x 5/8" Flat Head Screw
(L )
NOTE!
Locate spacers under inner holes in
lower channel and above threaded
holes in T-nuts.
C
L
K
J
FOLLOW STEPS 5, 6, AND 7 TO INSTALL GLASS
NOTE!
For product earlier than September 1994, which does not have a gap at each end of upper rail, install
the lower channel at the two-high as follows.
14 Mark and drill lower channel (C)
2.5"
(Both Ends)
5/16"
NOTE!
Drill completely through
the flanged side.
15 File down both drilled holes
NOTE!
Remove enough material from both drilled holes in flange surfaces (only) to
accommodate the head of a #10-32 pan head screw.
(Screw is not provided)
16 Install lower channel (C) to upper rail (J)
#10-32 T-nut
(E )
FOLLOW STEPS 5, 6, AND 7 TO INSTALL GLASS
J
#10-32 X 2"
Pan Head
Screw
E
J
K
C
L
E
J
C
L
K
C
J
E
E
J
C
17 Remove pole cover (M) and "W" channel (N)
GLASS PADS NEXT TO POWER POLE 18 Remove fabric pads (A)
A
A
FOLLOW STEPS 1 THRU 7 TO INSTALL GLASS
19 Re-assemble "W" channel (N) and pole cover (M)
Part No: Rev:
Page:
E.C.O. No: 5 of 5 F7021-6844217-112
CUSTOMER SERVICE PHONE: 1-800-426-8562
M
N
M
N
NOTE!
If W-channel is fastened with rivots drill
them out with a 5/32" or 4mm drill bit.
NOTE!
If W-Channel was fastened with rivots re-assemble
channel using 10-32 X .25 Pan Head Phillips
screws. (Screws are not provided).
N
M
A
A
/
