ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
1. PURPOSE
Provide step-by-step procedure for the stereo
installation.
2. SCOPE
This procedure is limited to the stereo
installation on the 130, 150 & 170 Super Sport.
3. DEFINITION
3.1. Not Applicable
4. RESPONSIBILITY
4.1. Not Applicable
5. TOOLS/EQUIPMENT REQUIRED
5.1. Drill
- 1/8” drill bit
- 11/16” drill bit
- 1/2” drill bit
- 9/64” bit w/countersink
- 3/4” hole saw
- Phillips head bit
5.2. Marine Sealant
5.3. Pliers
5.4. Vise grip “C” clamp
5.5. Measuring Tape
5.6. Pencil
6. SAFETY
6.1. Safety glasses or goggles are recommended.
7. FORMS
7.1. Not applicable
CONTENTS OF KIT PART#
JENSEN STEREO....................................1950779
ANTENNA.................................................1950780
MP3 INPUT...............................................1820320
WIRING HARNESS..................................1948329
STEREO ADAPTER.................................1952631
ACCESSORY SWITCH............................1948897
KNOB........................................................1733593
STEREO LABEL.......................................1952378
SPEAKERS (2).........................................1690555
SPEAKER BOX........................................1955994
HARDWARE PKG ......................901-BWSTEREO
Page 1 of 11
130SS Stereo Location 150 & 170SS Stereo Location
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8. PROCEDURE
8.1. Install the stereo switch.
8.1.1. Remove the anchor light switch knob from the post.
8.1.1. Using the measuring tape, measure 2 1/2” in from
the anchor light switch post center and using the
pencil, strike a vertical mark.
8.1.1.1. Using the measuring tape, measure 1 3/8”
UP from the radius and using the pencil,
strike a horizontal mark which intersects the
mark made in the previous step.
8.1.2. Using the drill w/ 7/16” drill bit, drill through the console
at the center of the marks made in steps 8.1.1. & 8.1.2.
8.1.3. Remove brass nut from accessory switch.
Page 2 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.1.4. Insert the switch, from under the console, into the hole drilled in step 8.1.2.
8.1.5. Replace the brass nut.
8.1.6. Using the pliers secure the switch to
the console.
8.1.7. Place the knobs onto the switches.
8.1.8. Apply stereo label to console
8.2. Install the stereo unit.
8.2.1. Using the measuring tape, measure 3” in from the port
edge of the console and using the pencil, strike a vertical
mark.
8.2.2. Using the measuring tape, measure 1 3/4” DOWN from
the top edge of the console and using the pencil, strike a
horizontal mark which intersects the mark made in the
previous step.
8.2.3. Using the drill with the 3/4” hole saw, cut through the
console at the center of the marks made in steps
8.2.1. & 8.2.2.
Page 3 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.2.4. Insert stereo cord into hole drilled
in the previous step.
8.2.4.1. Align stereo unit on face of
console.
8.2.5. While holding the stereo unit in
position, use the drill w/ 9/64” bit to
slightly mark the console through
the attachment holes in the stereo
unit.
.
8.2.6. Using the 9/64” drill bit
w/countersink, drill and slightly
countersink at the marks made in
the previous step.
8.2.6.1. Apply marine sealant to
the holes drilled in the
previous step.
Page 4 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.2.5. Using the Phillips head bit and
hardware supplied, secure the
stereo unit to the console.
8.3. Install the auxiliary input jack (130SS only)
8.3.1. Measure 5/8” out from the radius on the starboard
flat face of the storage pocket located on the
starboard side of the console. Using the pencil
make a vertical mark.
8.3.2. Measure 1 1/4” up from the base of the flat face of
the storage pocket. Using the pencil make a
horizontal mark to intersect the mark made in the
previous step.
8.3.3. Using the drill w/ 11/16” drill bit, drill through the
console at the intersection of the marks made in
steps 8.3.1. & 8.3.2.
8.3.4. Remove the nut from the back of the input jack.
8.3.5. insert the jack wires and jack into the hole made in
step 8.3.3.
8.3.6. Replace the nut and secure the input jack by
tightening the nut from the underside of the console.
Page 5 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.4. Install the auxiliary input jack (150SS only)
8.4.1. Measure 5/8” out from the radius on the starboard
flat face of the storage pocket located on the
starboard side of the console. Using the pencil
make a vertical mark.
8.4.2. Measure 3/4” up from the base of the flat face of
the storage pocket. Using the pencil make a
horizontal mark to intersect the mark made in the
previous step.
8.4.3. Using the drill w/ 11/16” drill bit, drill through the
console at the intersection of the marks made in
steps 8.4.1. & 8.4.2.
8.4.4. Remove the nut from the back of the input jack.
8.4.5. insert the jack wires and jack into the hole made in
step 8.4.3.
8.4.6. Replace the nut and secure the input jack by
tightening the nut from the underside of the console.
8.5. Install the speaker box.
8.5.1. Using the measuring tape, measure up 1/2” from the
edge of the backside of the console.
8.5.1.1. Place the bracket on the mark made in the
previous step making sure that it is centered
under the steering hub.
8.5.1.2 Using 3 #8 x 1/2” truss head screws, secure
the bracket to the console.
Page 5 of 11Page 6 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.5.2. Using the measuring tape, measure down 1 1/2” from
the console radius on the reinforcement block located
in the upper forward area under the console.
8.5.2.1. Place the plastic support strap on the mark
made in the previous.
8.5.2.2. Using 3 #10 x 1” truss head screws, secure
the strap to the reinforcement block.
8.5.3. Rest the notched end of the speaker box on the
bracket installed in step 8.4.2.
8.5.4. Insert the plastic support installed
in step 8.5.2. into the slot in the
upper forward section of the
speaker box.
8.5.4.1. Adjust the speaker box
to a level position and
using the “C” clamp,
secure the speaker box
To the plastic strap.
8.5.4.2. Using the hardware
supplied, secure the
speaker box to the
underside of the
console.
NOTE: Thru-bolt plastic strap to speaker box.
Page 7 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.6. Mount the stereo control box under the bench.
8.6.1. Place the control box in the
space under the bench on the
starboard side of the boat 2”
aft of the forward flange of
the seat.
NOTE: Assure that the wire
bundle faces the
starboard side of the
bench.
8.6.2. While holding the box to the underside of the
bench, use the pencil to mark the bench
through the screw holes in each side of the
control box.
8.6.3. Using the drill with 1/8” drill bit, drill the bench at the
marks made in the previous step.
NOTE: Drill only deeply enough to penetrate the
fiberglass layer. DO NOT drill into or through
the core material.
8.6.4. Using #8 x 5/8” truss head screws, secure the control
box to the underside of the bench.
Page 8 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.7. Run the wiring harness.
8.7.1. Using the harness adapter
(PN# 1952631) supplied,
attach the harness to the
control box.
8.7.2. Run the harness along the
starboard side of the boat to
the underside of the
console.
NOTE: Secure the harness
to the existing main
harness with tie
wraps.
8.7.3. Run the battery cable to the battery along
the underside of the bench alongside the
loom presently in place.
NOTE: Secure the cable at intervals to the
existing main harness with tie
wraps.
Page 9 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.8. Install the speakers.
8.8.1. Insert the speaker wires from the harness into
the top of the speaker box.
NOTE: There is a set of wires for each
speaker.
8.8.2. Attach the speaker wires to the speakers.
NOTE: Assure that the brass lead is attached
to the large square terminal.
8.8.3. Using four (4) #8 x 1” truss head screws,
secure the each speaker to the speaker box.
Page 10 of 11
ACCESSORY INSTALLATION
INSTRUCTIONS
STEREO
Installation Instructions for the 130, 150 & 170 Super Sport
Issue Date
05/11/2010
Rev: C
PROCEDURE NO.
AI-MS-012
8.8.4. Attach the speaker covers to the speakers by
aligning the notch and twisting clockwise.
8.9. Complete the installation of the stereo system by connecting the stereo and
auxiliary input to the wiring harness and connecting the battery terminals.
Stereo system Installation Is Complete
Page 11 of 11
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Boston Whaler 130 Super Sport Stereo Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Boston Whaler 160 Super Sport Bench Seat Installation guide
-
-
-
-
-
-
-
-
-