Boston Whaler 130 Super Sport Helm Seat Installation guide

ACCESSORY

INSTRUCTIONS

Page

1

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

Issue Date

06/15/2018

Rev. C

1.

PURPOSE

Provide step-by-step procedure for helm seat

with backrest installation.

2.

SCOPE

This procedure is limited to the helm seat with backrest

installation on the 130 & 160 Super Sport.

3.

DEFINITION

3.1.

Not Applicable

4.

RESPONSIBILITY

4.1.

Not Applicable

5.

TOOLS/EQUIPMENT REQUIRED

5.1.

Drill

-

1/8” drill bit

-

#5 drill bit

-

#2 Phillips head screwdriver

5.2.

Measuring Tape

5.3.

Pencil

5.4.

Hardware Pkg (Supplied)

.

CONTENTS OF KIT PART #

HELM SEAT W/BACKREST ..........................1038876

CUSHION.......................................................2316019

HARDWARE PKG.........................901BWHELMSEAT

6.

SAFETY

6.1.

Safety glasses or goggles are recommended.

7.

FORMS

7.1.

Not applicable

ACCESSORY INSTALL

INSTRUCTIONS

TION

Page

1

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

PROCEDURE NO. AI-MS-022

ACCESSORY

INSTRUCTIONS

Page

2

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

Issue Date

06/15/2018

Rev. C

8.

PROCEDURE

8.1.

Turn the seat bottom up and using the drill with #5 drill

bit, drill THRU the seat at each of the 4 locations

indicated in the photo at right.

NOTE: Ensure that the thru holes

are drilled ONLY through

the positions indicated.

8.2.

Using the drill with 1/8” bit, drill a center hole at

each of 2 aft positions on the seat

8.3.

Using the Phillips head screwdriver, insert a snap into

each of the 2 holes drilled in the previous step.

ACCESSORY

INSTRUCTIONS

Page

3

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

Issue Date

06/15/2018

Rev. C

8.4.

Using the tape measure, measure inboard from the

starboard edge of the bench.

8.4.1. Using the pencil, make a mark at 16 5/8”

(13SPT) 19 ¼” (16SPT) inboard from the

starboard AFT edge of the bench.

8.5.

Align the seat on the bench at the mark made in

the previous step and approximately ½” forward

of the aft edge of the bench.

NOTE: The forward lip of the seat

should align just forward of the

edge of the bench.

8.6.

Using the drill with #5 bit, make a mark on the bench

through the holes in the seat bottom.

ACCESSORY INSTALL

INSTRUCTIONS

TION

Page

3

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

PROCEDURE NO. AI-MS-022

ACCESSORY

INSTRUCTIONS

Page

4

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

Issue Date

06/15/2018

Rev. C

8.7.

Remove the seat.

8.7.1. Using the drill with the #5 bit, drill thru the bench at

the marks made in the previous step.

CAUTION: USE EXTREME CARE when drilling

through the bench to avoid injury or

damage to equipment. Remove the

gas tank and avoid the harness which

is secured to the underside of the

bench.

8.8.

Insert the hex head nuts into the seat

bottom.

8.8.1. Using the machine screws, flat

washers and lock washers

supplied, secure the seat to the

bench.

8.9.

Place the cushion onto the seat so that the two thin straps

face forward and the wide strap is aft.

ACCESSORY INSTALL

INSTRUCTIONS

TION

Page

4

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

PROCEDURE NO. AI-MS-022

ACCESSORY

INSTRUCTIONS

Page

5

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

Issue Date

06/15/2018

Rev. C

8.10.

Secure the cushion to the seat by attaching the aft

strap to the snaps installed in step 8.3.

8.11.

Hold either of the forward straps against the front

edge of the bench ensuring that the position of the

snap is such that when installed the cushion will

be taunt and secure.

8.11.1. Using the pencil, make a mark on the

front edge of the bench directly under

the snap.

8.12.

Using the drill with 1/8” bit, drill through the

bench at the mark made in the previous step.

ACCESSORY INSTALL

INSTRUCTIONS

of

6

HELM SEAT with BACKREST

Installation Instructions for the 150 & 170 Super Sport

Issue Date

05/10/2010

Rev:B

PROCEDURE NO. AI-MS-022

ACCESSORY INSTALLTION

INSTRUCTIONS Page

6

of

6

HELM SEAT with BACKREST

Installation Instructions for the 130 & 160 Super Sport

Issue Date

06/15/2018

Rev. C

PROCEDURE NO. AI-MS-022

8.13.

Using the Phillips head screwdriver, insert a snap into

the hole drilled in the previous step.

NOTE: Repeat steps 8.11. thru 8.13. for the

remaining forward strap.

8.14.

Attach front straps to the snaps installed in previous

steps.

Helm Seat Installation Is Complete

NOTE: If desired, the helm seat can

be installed on the companion

side of the bench seat in

either a forward or aft facing

fashion by following the same

procedure as explained above.

Boston Whaler 130 Super Sport Helm Seat Installation guide

Boston Whaler 130 Super Sport Helm Seat Installation guide

Related papers

Other documents