Furuno TZTL12F Installation guide

Brand: Furuno

Model: TZTL12F

Type: Installation guide

This manual is also suitable for

TZTL15F

www.furuno.com

ll brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Installation Manual

MULTI FUNCTION DISPLAY

Model TZTL12F/TZTL15F

SAFETY INSTRUCTIONS ................................................................................................ i

SYSTEM CONFIGURATION ........................................................................................... ii

EQUIPMENT LISTS........................................................................................................ iii

1. MOUNTING..............................................................................................................1-1

1.1 Mounting Considerations ...................................................................................................1-1

1.2 Flush Mounting ..................................................................................................................1-2

1.3 Retrofit Kit for TZTL12F (option) and Front Fixing Panel Kit for TZTL15F (option) ...........1-4

1.4 Desktop Mounting (option).................................................................................................1-6

1.5 Installation of Transducers.................................................................................................1-8

1.6 Installation of Sensors (option) ........................................................................................1-18

2. WIRING....................................................................................................................2-1

2.1 Interface Connections (Rear of Unit) .................................................................................2-1

2.2 How to Secure and Waterproof Connections.....................................................................2-2

2.3 MULTI Cable......................................................................................................................2-2

2.4 DRS Radar Sensor Connections .......................................................................................2-6

2.5 Network Connector ............................................................................................................2-7

2.6 Video In, Video Out and USB Connections .......................................................................2-7

2.7 CAN bus (NMEA2000 Connector) .....................................................................................2-8

2.8 Example NavNet TZtouch2 System Configurations.........................................................2-13

3. HOW TO SET UP THE EQUIPMENT......................................................................3-1

3.1 How to Set Time Zone, Time Format and Language.........................................................3-3

3.2 How to Set Units of Measurement .....................................................................................3-5

3.3 Initial Setup ........................................................................................................................3-6

3.4 How to Set Up the Radar.................................................................................................3-12

3.5 How to Set Up the Sounder .............................................................................................3-15

3.6 Wireless LAN Setting .......................................................................................................3-20

APPENDIX 1 INSTALLATION OF TEMPERATURE SENSORS ............................AP-1

PACKING LISTS ......................................................................................................... A-1

OUTLINE DRAWINGS ................................................................................................ D-1

INTERCONNECTION DIAGRAM ................................................................................ S-1

The paper used in this manual

is elemental chlorine free.

・FURUNO Authorized Distributor/Dealer

9-52 Ashihara-cho,

Nishinomiya, 662-8580, JAPAN

JAN

2015

Printed in Japan

JUL

27, 2020

Pub. No.

IME-44870-G

(

GREG

)

TZTL12F/TZTL15F

0 0 0 1 9 0 0 7 4 1 6

SAFETY INSTRUCTIONS

The installer must read the appropriate safety instructions before attempting to install the

equipment.

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

WARNING

CAUTION

Warning, Caution Prohibitive Action Mandatory Action

WARNING

ELECTRICAL SHOCK HAZARD

Do not open the equipment

unless totally familiar with

electrical circuits.

Only qualified personnel should

work inside the equipment.

Turn off the power at the

switchboard before beginning

the installation.

Fire or electrical shock can result

if the power is left on.

CAUTION

Be sure that the power supply is

compatible with the voltage

rating of the equipment.

Connection of an incorrect power

supply can cause fire or damage

the equipment.

Use the proper fuse.

Use of an incorrect fuse may

damage the equipment.

The front panel is made of glass.

Handle it with care.

Injury can result if the glass breaks.

Observe the following compass safe

distances to prevent interference to a

magnetic compass:

Standard

compass

TZTL12F

TZTL15F

Steering

compass

0.75 m

0.50 m

0.75 m 0.45 m

(Examples of symbols)

Model

Ground the equipment to prevent

electrical shock and mutual interference.

If your vessel is configured with

an autopilot system, install an

autopilot control unit (or emer-

gency autopilot stop button) at

each helm station, to allow you

to disable the autopilot in an

emergency.

If the autopilot cannot be disabled,

accidents may result.

SYSTEM CONFIGURATION

CCD Camera

FI-5002

SC-30

SCX-20

GP-33/GP-330B

FA-40/FA-70

NAVpilot Series

FI-50/70

IF-NMEA2K1/2

IF-NMEAFI

12/24 VDC

Event SW

External Buzzer

Operator Fitness

Power input for NMEA2000

NMEA0183 out

BBDS1, DFF series

Environmental category

Radar antenna: Exposed to the weather

All other units: Protected from the weather

AIS Transponder

Radar and required power supply unit.

DRS2D/4D/6A/12A: PSU-012; DRS25A/: PSU-013; DRS2D/4D: PSU-017

See the radar sensor Installation Manual (IME-35670) for details.

A maximum of 6 NavNet TZtouch2 units can be connected via Ethernet hub. With connection of a

TZT2BB unit, the maximum number of units is 4. These units are internally fittted with a GPS

antenna/receiver and fish finder as standard.

Use an after-market PoE hub. The NETGEAR GS108PE is confirmed as compatible. Compatibility tests are

limited to general use as part of this configuration and in no way indicates overall capability.

Further, FURUNO cannot guarantee the functionality of any after-market hub.

FURUNO networks allow for a maximum of three Ethernet Hub HUB-101s.

Exceeding this can result in undesirable results.

HUB -101*

FA-30/50

FAX-30

FUSION-Link Equipment

BBWX weather receiver

Wide Monitor

Remote Controller

MCU-002 or MCU-004

SD Card Unit SDU-001

Open Array

Radar Sensors

12-24

VDC

DRS2D/DRS4D

POWER SUPPLY UNIT*

PSU-012/PSU-013

Radome Radar

Sensors

DRS4A/DRS6A/DRS12A/DRS25A

POWER

SUPPLY

UNIT*

PSU-017

For PSU-017

DRS4DL, DRS4DL+

12-24 VDC

DRS4D-NXT

24 VDC

Select one of radome

or open array sensor.

DRS6A X-Class/DRS12A X-Class/DRS25A X-Class/

DRS6A-NXT/DRS12A-NXT DRS25A-NXT

: Standard supply

: Optional or local

supply

Multi Beam Sonar

(DFF-3D)

IP Camera

12-24 VDC

Transducer

Remote Controller

MCU-005

PoE HUB*

Multi Function Display*

TZTL12F

TZTL15F

Multi Function Display*

TZTL12F

TZTL15F

FAR-2xx7/2xx8 series

FAR-15x3/15x8 series

iii

EQUIPMENT LISTS

Standard supply

Optional supply

Name Type Code No. Qty Remarks

Multi Function Display

TZTL12F -

TZTL15F -

Installation Materials CP19-01810 000-033-430 1 For TZTL12F/15F

Accessories FP19-02011 001-337-390 1

Spare Parts SP19-00601 001-023-040

Fuses (Type: FBG0-A 125V 5A PBF,

Code: 000-155-853-10, 2 pcs.)

Name Type Code No. Remarks

Joint Box TL-CAT-012 000-167-140-10 For LAN network

Remote Control Unit MCU-002 -

MCU-004 -

MCU-005 -

SD Card Unit SDU-001 -

NMEA2000-Interface

Unit

IF-NMEA2K1 -

NMEA Data Converter IF-NMEA2K2 -

IF-NMEAFI -

Network HUB HUB-101 -

Matching Box MB-1100 000-041-353-00 Required for some

transducers.

See next page.

Power Supply Unit PSU-012 000-021-609-00 w/DRS2D/4D/4A/6A/12A

PSU-013 000-021-610-00 w/DRS25A

PSU-017 000-022-997-00 w/DRS2D/4D

Rectifier RU-3423 000-030-443-00

PR-62 000-013-484-00 100 VAC

000-013-485-00 110 VAC

000-013-486-00 220 VAC

000-013-487-00 230 VAC

RU-1746B-2 000-030-439-00

CAN bus Cable Assy. M12-05BM+05BF-010 001-105-750-10 w/connectors (light), 1 m

M12-05BM+05BF-020 001-105-760-10 w/connectors (light), 2 m

M12-05BM+05BF-060 001-105-770-10 w/connectors (light), 6 m

M12-05BFFM-010 001-105-780-10 w/connector (light), 1 m

M12-05BFFM-020 001-105-790-10 w/connector (light), 2 m

M12-05BFFM-060 001-105-800-10 w/connector (light), 6 m

CB-05PM+05BF-010 000-167-968-10 w/connectors (heavy), 1 m

CB-05PM+05BF-020 000-167-969-10 w/connectors (heavy), 2 m

CB-05PM+05BF-060 000-167-970-10 w/connectors (heavy), 6 m

CB-05BFFM-010 000-167-971-10 w/connector (heavy), 1 m

CB-05BFFM-020 000-167-972-10 w/connector (heavy), 2 m

CB-05BFFM-060 000-167-973-10 w/connector (heavy), 6 m

EQUIPMENT LISTS

Cable Assy. 02S4147-1 000-141-082 For speed/temp. and temp.

sensors

MJ Cable Assy. MJ-A6SPF0016-005C 000-159-689-10 For FAX-30

External Buzzer OP03-136 000-086-443-00 Buzzer: PKB5-3A40

Network (LAN) Cable MOD-Z072-020+ 001-167-880-10 LAN cable, cross-pair, 2 m

MOD-Z073-030+ 000-167-171-10

LAN cable, straight, 2 pairs,

3 m

MOD-Z072-050+ 001-167-890-10 LAN cable, cross-pair, 5 m

MOD-Z072-100+ 001-167-900-10 LAN cable, cross-pair, 10 m

CAN bus Connector SS-050505-FMF-TS001 000-168-603-10 Micro style: 3

NC-050505-FMF-TS001 000-160-807-10 Mini style: 2, micro style: 1

LTWMC-05BMMT-

SL8001

000-168-604-10

Micro style, male, termina-

tion resistor

LTWMN-05AMMT-

SL8001

000-160-508-10

Mini style, male, termination

resistor

LTWMC-05BFFT-

SL8001

000-168-605-10

Micro style, female,

termination resistor

LTWMN-05AFFT-

SL8001

000-160-509-10

Mini style, female,

termination resistor

FRU-0505-FF-IS 001-077-830-10 w/in-line terminator

Transducer 520-5PSD (*) 000-015-204-00

520-5MSD (*) 000-015-212-00

525-5PWD (*) 000-146-966-00

520-PLD (*) 000-023-680-00

525T-BSD (*) 000-023-020-00

525T-PWD (*) 000-023-019-00

SS60-SLTD/12 (*) 000-023-676-00

SS60-SLTD/20 (*) 000-023-677-00

525T-LTD/12 (*) 000-023-679-00

525T-LTD/20 (*) 000-023-678-00

50/200-1T *10M* (*) 000-015-170-00 Matching box MB-1100

required for installation of

these transducers.

50B-6 *10M* 000-015-042-00

50B-6B *15M* 000-015-043-00

200B-5S *10M* 000-015-029-00

Triducer 526TID-HDD (*) 000-023-021-00

525STID-PWD (*) 000-011-784-00

525STID-MSD (*) 000-011-783-00

Extension Cable** C332 10M 001-464-120 10m, for transducer

Speed/Temperature

Sensor

ST-02MSB 000-137-986-01 Thru-hull type, metal

ST-02PSB 000-137-987-01 Thru-hull type, plastic

Temperature Sensor T-04MSB 000-026-893 Thru-hull type

T-04MTB 000-026-894 Transom mount

Bracket 12 OP19-13 001-337-410-00 For TZTL12F

Bracket 15 OP19-14 001-337-420-00 For TZTL15F

Retrofit Kit For VX2

10.4"

OP19-15 001-337-430-00 For TZTL12F

Retrofit Kit For MDF12 OP19-16 001-337-440-00 For TZTL12F

Front Fixing Panel Kit OP19-17 001-337-450-00 For TZTL15F

Name Type Code No. Remarks

EQUIPMENT LISTS

*: Compatible with ACCU-FISH

™

, Bottom Discrimination and RezBoost

™

Enhanced mode. All list-

ed transducers are compatible with RezBoost

™

Standard mode.

Inside Hull Kit S 22S0191 001-321-930 not available with bottom

discrimination display,

w/installation instructions.

Operator’s Manual OME-44870-* 000-190-069-1* English

(* denotes version number)

User’s Guide E42-01403-* 000-179-419-11 MCU-002, English

User’s Guide E42-01509-* 000-191-291-10 MCU-004, English

**: Use of the extension cable may cause the following problems:

• Reduced detection ability

• Wrong ACCU-FISH

™

information (fish length smaller than actual length, fewer fish detections, er-

ror in individual fish detection).

• Wrong speed data

• No TD-ID recognition

Name Type Code No. Remarks

EQUIPMENT LISTS

This page is intentionally left blank.

1-1

1. MOUNTING

1.1 Mounting Considerations

When selecting a mounting location for NavNet TZtouch2, keep the following in mind:

• The temperature at the mounting location shall be between -15°C and +55°C.

• The humidity at the mounting location shall be 93% or less at 40°C.

• Locate the unit away from exhaust pipes and ventilators.

• The mounting location should be well ventilated.

• Mount the unit where shock and vibration are minimal (compliant with IEC 60945

Ed.4).

• Keep the unit away from electromagnetic field generating equipment such as

motors and generators.

• For maintenance and checking purposes, leave sufficient space around the unit and

leave slack in cables. Minimum recommended space is shown in the outline

drawing for the display units.

• Do not mount the NavNet TZtouch2 on the overhead.

• A magnetic compass will be affected if the equipment is placed too close to it.

Observe the compass safe distances shown in the SAFETY INSTRUCTIONS to

prevent disturbance to the magnetic compass.

• Mount the unit in a location where the internal GPS antenna can transmit and

receive GPS data without obstruction. Where this is not possible, connect the

NavNet TZtouch2 to an external GPS antenna, such as the GP-330B, via a

NMEA2000 network.

The NavNet TZtouch2 can be flush mounted in a console or panel, or mounted on a

desktop.

When removing the equipment

If the equipment is removed from the vessel, cover the connector of the cable with the

supplied cap to keep dust out of the connector.

TZTL15FTZTL12F

1. MOUNTING

1-2

1.2 Flush Mounting

There are two methods of flush mount installation. One method uses pilot holes to se-

cure the panel at the installation location (Method B), the other method does not use

pilot holes (Method A). The merits and demerits of each method is listed in the table

below.

Referring to the figure below, select a flat mounting location. Read the installation in-

structions before starting. Pay particular attention to the notes; failure to follow these

instructions may cause damage to the unit.

Note: Ensure the mounting location is flat, with no indents or protrusions, to allow a

secure fit.

1.2.1 Method A: Pilot holes cannot be opened.

1. Prepare a cutout in the mounting location using the template (supplied) for the

NavNet TZtouch2.

2. Fasten the wing bolts and the wing nuts of the flush mount fixture so that the pro-

tector for screw moves to the flush mount fixture.

Note: Slowly fasten the four wing bolts evenly with your hand. Do not use a tool

to fasten the wing bolts. A tool can be used to fasten the wing nuts; use caution

so as not to damage the wings or thread.

Method A Method B

Merits No pilot holes are required.

Fine adjustment is available.

Shorter process than Method A.

Demerits Longer process than Method A. Pilot holes are required.

Fine adjustment is not available.

Flat

Curved Bumpy

Wing nut

Wing bolt

Flush mount fixture

Protector for screw

Move to the fixture

1. MOUNTING

1-3

3. Connect all cables at the back of the NavNet TZtouch2. (See chapter 2.)

4. Set the NavNet TZtouch2 to the cutout.

5. Set NavNet TZtouch2 to the cutout made with step 1.

6. Fasten each wing bolt so that the protector for screw touches the mounting panel.

7. Fasten the wing nuts tightly.

Note: Use of excessive torque when fastening the wing bolts can cause the flush

mount fixture to tilt or warp. Check that the flush mount fixtures and wing bolts are

not tilted or warped, referring to the following examples.

2. Fasten NavNet TZtouch2 with flush mount fixture.

1. Set NavNet TZtouch2 to the cutout.

Wing bolt

Wing nut

Flush mounting fixture

Protector for screw

Mounting panel

TZTL

unit

TZTL

unit

Flush mount fixture is fixed at right angle. Flush mount fixture is warped,

wing bolts are tilted.

1. MOUNTING

1-4

1.2.2 Method B: Pilot holes can be opened.

1. Prepare a cutout at the mounting location using the template. (supplied)

2. Remove the flush mount plate from the NavNet TZtouch2. The flush mount plate

is not fastened to the NavNet TZtouch2, and can be easily removed.

3. Fit the flush mount plate to the cutout. Fasten the flush mount plate to the pilot

holes of cutout with flat headed self-tapping screws (3 x 20 SUS XM7). Insert the

NavNet TZtouch2 to the cutout and fasten with hex bolts (supplied).

1.3 Retrofit Kit for TZTL12F (option) and Front Fixing

Panel Kit for TZTL15F (option)

When upgrading to the TZTL12F or front-mounting the TZTL15F, use the kit which

matches your old equipment. (Refer to the table below for details.)

Note: Remove the flush mounting sponges attached to the back of the NavNet TZ-

touch2. Take care that there is no sponge left on the back of the NavNet TZtouch2.

Optional kit Code No. Contains Remarks

OP19-15 001-337-430 F Mount Panel A (Code

No.: 100-397-090-10),

5u20 SUS304, 4 pcs.

(Code No.: 001-336-820)

For NavNet/NavNet Vx2 displays.

(RDP-138/139/149/151)

(For TZTL12F)

OP19-16 001-337-440 F Mount Panel B (Code

No.: 100-397-100-10),

5u20 SUS304, 4 pcs.

(Code No.: 001-336-820)

For NavNet3D MFD12.

(For TZTL12F)

OP19-17 001-337-450 F Mount Panel 15 (Code

No.: 100-397-600-10),

5u20 SUS304, 4 pcs.

(Code No.: 001-336-820)

TZTL15F Front Fixing Panel Kit.

(For TZTL15F)

䐟

Fit the flush mount plate to the

cutout, fasten it to the cutout with

flat headed self-tapping screws and insert

the NavNet TZtouch2 to the cutout.

Flat headed self-tapping screws 3 x 20 SUS XM-7 (Supplied)

䐠

Secure the NavNet TZtouch2 with the

hex bolts. (supplied)

䐠

Secure the NavNet TZtouch2 with the

hex bolts. (supplied)

1. MOUNTING

1-5

1. Prepare a cutout in the mounting location using the template (supplied) for the

NavNet TZtouch2.

2. Place the NavNet TZtouch2 unit face-down on a a soft, clean surface.

3. Set the F Mount Panel to the NavNet TZtouch2 unit, then using the hex bolts at-

tached to Navnet TZ touch2, fix the F Mount Panel to the unit.

4. Set the unit and F Mount Panel into the cutout as shown in the figure to the right,

then use the supplied self-tapping screws (SUS304 u 4 pcs.), fix the F Mount

Panel to the console.

Note: Where the mounting location may be exposed to water (spray or splash),

apply a bead of marine sealant around the rear of the F Mount Panel, for

waterproofing, before setting the F Mount Panel and unit into the cutout. Wipe the

area clean to remove any marine sealant residue and allow time for the marine

sealant to dry.

Hex bolt Hex bolt

TZTL unit

Frontmount panel

sole

cuto

tConsole cuto

Self-tapping

SUS304 screws

1. MOUNTING

1-6

1.4 Desktop Mounting (option)

Follow the appropriate procedure below to mount the NavNet TZtouch2.

Note: Remove the flush mounting sponges attached to the back of the NavNet TZ-

touch2. Take care that there is no sponge left on the back of the NavNet TZtouch2.

1.4.1 How to mount the TZTL12F

Use the optional kit Bracket12 (contents shown below), for mounting the TZTL12F.

1. Fix the hanger by using self-tapping screws (5u20

SUS304, supplied). The screw locations are indicated

in the figure to the right.

2. Place the TZTL12F face-down on a soft,

clean surface, then screw the knob bolts into

the

TZTL12F, leaving a gap of approximately 30

mm.

3. Set the TZTL12F unit to the hanger and tight-

en the knob bolts.

Note: When setting the TZTL12F into the

hanger, the concave section of the unit and the

convex section of the hanger must be aligned.

Type Code Contents

OP19-13 001-337-410 Knob bolt u 2 (Code No.: 100-365-900-10), Self-tapping

screws (SUS304 5u20) u 4 (Code No.: 000-162-608-10),

Hanger u 1 (Code No.: 100-397-080-10).

Approx. 30 mm gap

Knob bolts

Hanger

Unit concave Hanger convex

1. MOUNTING

1-7

1.4.2 How to mount the TZTL15F

Use the optional kit Bracket15 (contents shown below), for mounting the TZTL15F.

1. Fix the hanger by using self-tapping screws (5u20 SUS304, supplied). The screw

locations are indicated in the figure below.

2. Place the TZTL15F face-down on a soft, clean surface, then fit the washers and

knob bolts as shown in the figure below, leaving a gap of approximately 30 mm.

The washers have a leading edge which must face the unit.

3. Set the TZTL15F unit to the hanger and tighten the knob bolts.

Type Code Contents

OP19-14 001-337-420 Knob bolt u 2 (Code No.: 100-346-502-10), Washer u 2

(Code No.: 100-076-101-10), Self-tapping screws (SUS304

5u20) u 4 (Code No.: 000-162-608-10), Hanger u 1 (Code:

No.: 001-360-970).

Knob Knob

Washer Washer

Washer leading edge

Hanger

Knob boltKnob bolt

1. MOUNTING

1-8

1.5 Installation of Transducers

Note: For instructions regarding installation of DFF-3D transducers, see the DFF-3D

operator’s manual.

1.5.1 How to mount a transducer through the hull

Transducer mounting location

The thru-hull mount transducer provides the best performance of all, since the

transducer protrudes from the hull and the effect of air bubbles and turbulence near

the hull skin is reduced. If your boat has a keel, the transducer should be at least 30

cm away from it.

The performance of this fish finder is directly related to the mounting location of the

transducer, especially for high-speed cruising. The installation should be planned in

advance, keeping the length of the transducer cable and the following factors in mind:

• Air bubbles and turbulence caused by movement of the boat seriously degrade the

sounding capability of the transducer. The transducer should, therefore, be located

in a position where water flow is the smoothest. Noise from the propellers also

adversely affects performance and the transducer should not be mounted nearby.

The lifting strakes are notorious for creating acoustic noise, and these must be

avoided by keeping the transducer inboard of them.

• The transducer must always remain submerged, even when the boat is rolling,

pitching or up on a plane at high speed.

• A practical choice would be somewhere between 1/3 and 1/2 of your boat's length

from the stern. For planing hulls, a practical location is generally rather far astern,

so that the transducer is always in water regardless of the planing attitude.

●

Within the wetted bottom area

●

Deadrise angle within 15°

●

Position 1/2 to 1/3 of the hull from stern.

●

15 to 30 cm off center line (inside first lifting

strakes.)

DEEP V

HULL

HIGH SPEED

V HULL

120

Unit: mm

520-5PSD

520-5MSD

BOW

1. MOUNTING

1-9

Installation procedure

1. With the boat hauled out of the water, mark the location chosen for mounting the

transducer on the bottom of the hull.

2. If the hull is not level within 15° in any direction, fairing blocks made out of teak

should be used between the transducer and hull, both inside and outside, to keep

the transducer face parallel with the water line. Fabricate the fairing block as

shown below and make the entire surface as smooth as possible to provide an

undisturbed flow of water around the transducer. The fairing block should be

smaller than the transducer itself to provide a channel to divert turbulent water

around the sides of the transducer rather than over its face.

3. Drill a hole just large enough to pass the threaded stuffing tube of the transducer

through the hull, making sure it is drilled vertically.

4. Apply a sufficient amount of high quality caulking compound to the top surface of

the transducer, around the threads of the stuffing tube and inside the mounting

hole (and fairing blocks if used) to ensure watertight mounting.

5. Mount the transducer and fairing blocks and tighten the locknut. Be sure that the

transducer is properly oriented and its working face is parallel to the waterline.

Note: Do not over-stress the stuffing tube and locknut through excessive tightening,

since the wood block will swell when the boat is placed in the water. It is suggested

that the nut be tightened lightly at installation and re-tightened several days after the

boat has been launched.

Hole for

stuffing tube

Saw along

slope of hull.

Upper Half

Lower Half

BOW

Flat Hull

Deep-V Hull

Flat Washer

Rubber Washer

Fairing

Block

Hull

Flat Washer

Rubber

Washer

Cork

Washer

1. MOUNTING

1-10

Transducer preparation

Before putting your boat in water, wipe the face of the transducer thoroughly with a

detergent liquid soap. This will lessen the time necessary for the transducer to have

good contact with the water. Otherwise the time required for complete "saturation" will

be lengthened and performance will be reduced.

DO NOT paint the transducer. Performance will be affected.

1.5.2 Transom mount transducer

The optional transom mount transducer is very commonly employed, usually on

relatively small I/O or outboard boats. Do not use this method on an inboard motor

boat because turbulence is created by the propeller ahead of the transducer.

DO NOT over-tighten screws, to prevent damage to the transducer.

Installation procedure

A suitable mounting location is at least 50 cm away from the engine and where the

water flow is smooth.

1. Drill four pilot holes for self-tapping screw (5u20) in the mounting location.

2. Coat the threads of the self-tapping screws (5x14) for the transducer with marine

sealant for waterproofing. Attach the transducer to the mounting location with the

self-tapping screws.

3. Adjust the transducer position so the transducer faces right to the bottom. If

necessary, to improve water flow and minimize air bubbles staying on the

transducer face, incline the transducer about 5° at the rear. This may require a

certain amount of experimentation for fine tuning at high cruising speeds.

4. Tape the location shown in the figure below.

5. Fill the gap between the wedge front of

the transducer and transom with ep-

oxy material to eliminate any air spac-

es.

6. After the epoxy hardens, remove the tape.

Transom

Strake

Parallel with hull

Mount at the strake.

Less than 10°Less than 10°

Over 10°

5x20

M5x14

5°

Taping

Bracket

Transducer

2 to 5°

Epoxy material

Hull

1. MOUNTING

1-11

1.5.3 How to mount a transducer inside the hull

The transducer may also be installed inside the hull on FRP boats. However, this

installation method affects the ability to detect the bottom, fish and other objects

because the ultrasound pulse is weakened when it passes through the hull.

Note: This mounting method should not be used to mount the transducer that

supports the RezBoost

™

, ACCU-FISH

™

and/or bottom discrimination display feature,

since

performance is greatly degraded.

Necessary tools

The following tools are required:

Remarks on installation

Installation procedure

The attenuation of the ultrasound pulse varies with the thickness of the hull. Select a

location where attenuation is the lowest.

1. Select 2-3 locations considering the four points mentioned below.

2. Decide the most suitable site from the locations selected.

1) Connect the power cable and transducer cable to the display unit.

• Sandpaper (#100)

• Marine sealant

• Water-filled plastic bag

• Do the installation with the ship moored at a dock, etc. The water depth should be

6.5 to 32 feet (2 to 10 meters).

• Turn off the engine.

• Do not power the unit with the transducer in the air, to prevent damage to the

transducer.

• Do not use this method on a double layer hull.

• Before attaching the transducer to the hull, check that the site is suitable, by following

steps 1 to 3 in the installation procedure below.

• Mount the transducer at a location 1/2 to 1/3 of the length of your boat from the

stern.

• The mounting location is between 15 to 50 cm from the centerline of the hull.

• Do not place the transducer over hull struts or ribs which run under the hull.

• Avoid a location where the rising angle of the hull exceeds 15°, to minimize the

effect of the boat's rolling.

1/3

1/2

Centerline

Transducer

mounting

location

50 cm

15 cm

1. MOUNTING

1-12

2) Put the transducer into water-filled plastic bag.

Press the transducer against the chosen site.

3) Tap (power switch) to turn the power on.

4) After the startup procedure completes (approx.

90 seconds), the last used display appears.

Tap the [Home] icon ( ) to

show the home screen and display mode

settings. See section 3.3 for how to use the

menu.

5) Drag the menu to show [Sounder] in the menu, then tap [Sounder].

6) Drag the [Sounder] menu to show the [SOUNDER INITIAL SETUP] menu.

7) Tap [Fish Finder Source].

8) Confirm the available fish finder from the list of available sounders, then tap

the appropriate fish finder. For the purpose of this example, the default setting

[TZTL] (internal sounder) is selected as the source.

9) Tap the [<] icon to return to the [Sounder] menu

10) Drag the [Sounder] menu to show the [SOUNDER INITIAL SETUP] menu.

11) Tap [Transducer Setup].

12) Tap [Transducer Setup Type].

13) Tap [Model], then tap the [<] icon to return to [Transducer Setup] menu.

14) Tap [Model Number], drag the menu to show your transducer model, then tap

the transducer model number.

15) Tap the [<] icon twice to return to the [Sounder] menu, then drag the [Sounder]

to show the [SOUNDER INITIAL SETUP] menu.

16) At the [Transmission Power] menu item, set the transmission power to a level

of [2].

17) Drag the menu to show [Sounder Transmit], then tap [Sounder Transmit].

Check if the bottom echo appears on the right side of the screen, in the display

area.

If no bottom echo appears, repeat the procedure unit a suitable location is

found.

3. Remove the transducer from the plastic bag and wipe the face of transducer with

a cloth to remove water and any foreign material. Lightly roughen the face with

#100 sandpaper. Also, use the sandpaper to roughen the inside of the hull where

the transducer is to be mounted.

4. Wipe off any sandpaper dust from the face of the transducer.

Plastic bag

Water

Hull plate

Page is loading ...

Furuno TZTL12F Installation guide

Brand: Furuno

Model: TZTL12F

Type: Installation guide

This manual is also suitable for

TZTL15F

Download PDF

report

Furuno TZTL12F Installation guide

This manual is also suitable for

Furuno TZTL12F Installation guide

Related papers

Other documents