Whirlpool AKR 957 IX Program Chart

Brand: Whirlpool

Model: AKR 957 IX

Category: Cooker hoods

Type: Program Chart

This manual is also suitable for

Whirlpool AKR 957 IX is a cooker hood designed to remove fumes and odors from your kitchen. With a minimum height of 65 cm above electric cookers and 75 cm above gas cookers, it features four speed settings, halogen bulbs for illumination, and a telescopic flue for flexible positioning. The grease filter should be cleaned at least once a month, and the carbon filter can be washed and reactivated.



5019 318 33083

AKR 928 - AKR 958

INSTALLATIONSANGABEN

Mindestabstand zur Kochfläche: 65 cm (Elektroplatten), 75 cm (Gas-, Öl-,

Kohlekochplatten). Folgen Sie bei der Installation der Nummerierung

.....). Das Auslassrohr und die Befestigungsmanschetten (15) sind

nicht im Lieferumfang inbegriffen und müssen gesondert erworben werden.

Prüfen Sie den Stromanschluss der Beleuchtung und des Motors (2-20).

Befestigen Sie die abnehmbare Verkleidung mit den Schrauben fest an der

Dunstabzugshaube (17). Die Verkleidung kann verschiedene Formen haben,

trotzdem bleiben Montage- und Befestigungsverfahren gleich.

INSTALLATION SHEET

Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil or

coal cookers). To install follow points (1

.....). The discharge flue and

fixing clamps (15) are not provided and must be purchased separately. Check for

correct electrical connections of lights and motor (2-20). Tighten the screws

fixing the removable casing to the hood (17). The casing can be in various

shapes, but the procedure for fitting and fixing to the hood is the same.

FICHE D'INSTALLATION

Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique), 75

cm (cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la

numérotation (1

.....). Le tuyau d'évacuation et les colliers de fixation

(15) ne sont pas fournis avec l'appareil et doivent être achetés à part. Contrôlez

que le branchement électrique de l'éclairage et du moteur ont été correctement

effectués (2-20) Serrez à fond les vis fixant le capot amovible à la hotte (17).

Le modèle du capot peut être différent mais la procédure d'insertion et de

fixation à la hotte reste identique.

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 65 cm (elektrische kooktoestellen), 75 cm

(kooktoestellen op gas, gasolie of kolen). Volg voor de montage de nummering

.....). De afvoerleiding en de bevestigingsklemmen (15) worden niet

bijgeleverd en dienen apart aangeschaft te worden. Verzeker u ervan dat de

verlichting en de motor correct aangesloten zijn (2-20). Draai de twee

schroeven, waarmee de losse mantel aan de kap (17) is bevestigd, heel goed aan.

De procedure voor plaatsing en bevestiging van de kap in de mantel is identiek

voor alle type mantels.

31833083.fm Page 1 Friday, October 10, 2003 4:39 PM



5019 318 33083

AKR 928 - AKR 958

FICHA DE INSTALACIÓN

Distancia mínima desde los quemadores: 65 cm (quemadores eléctricos), 75 cm

(quemadores a gas, gasóleo o carbón). Para el montaje, siga la numeración

...). El tubo de evacuación y las abrazaderas de fijación (15) no se

suministran de fábrica sino que se deben comprar. Compruebe que la conexión

eléctrica de las luces y del motor es correcta (2-20). Atornille bien los tornillos

que fijan el revestimento desmontable a la campana (17). El revestimento puede

ser de distintas formas, pero el procedimiento para introducirlo y fijarlo a la

campana siempre es el mismo.

FICHA DE INSTALAÇÃO

Distância mínima dos fogões: 65 cm (fogões eléctricos), 75 cm (fogões a gás,

óleo ou carbono). Para montar siga a numeração (1

.....). O tubo de

descarga e tiras de fixação (15) não são fornecidos com o aparelho pelo que

devem ser adquiridos. Controle se a ligação eléctrica das luzes e do motor foi

feita correctamente (2-20). Aperte muito bem os parafusos que prendem a

cobertura amovível do exaustor (17). A cobertura pode ser de diferentes formas,

mas o procedimento e a fixação ao exaustor permanece idêntica.

SCHEDA INSTALLAZIONE

Distanza minima dai fuochi: 65 cm (fuochi elettrici), 75 cm (fuochi a gas,

gasolio o carbone). Per il montaggio seguire la numerazione (1

.....).

Tubo di scarico e fascette di fissaggio (15) non sono fornite e vanno acquistate.

Controllare il corretto collegamento elettrico di luci e motore (2-20). Serrare con

decisione le viti che fissano il mantello rimovibile alla cappa (17). Il mantello

può essere di forme diverse, ma la procedura di inserimento e fissaggio alla

cappa rimane identica.

ùüùü+ùùùþ

ü$12.)12.1.)2"0120"FP02!"0120"FP

0120".0! #02!0. #0! #.+.22  21

.  #1202.!1





1&."..&".2.

 !.120!&1"/0/.202.02 . !! 32!..!0 

.. 2 *$&!12ü2021&1202!1*/01 

3&212+.  2!320.2"/0" #1#!.2 *2 

.3.! *0 #.12 . !! 32!. #. !0.

$0/.3 !02)1$.././.1.2  21".120!&1"

12 . !! 32!..!.0 /.

31833083.fm Page 2 Friday, October 10, 2003 4:39 PM



5019 318 33083

AKR 928 - AKR 958

31833083.fm Page 3 Friday, October 10, 2003 4:39 PM



5019 318 33083

AKR 928 - AKR 958

21b

19b

Ø 150

19a

21a

21b

19a

31833083.fm Page 4 Friday, October 10, 2003 4:39 PM



AKR 928 - AKR 958

5019 318 33083

INSTALLATION - ASSEMBLY INSTRUCTIONS

Preliminary information for installing the hood

Before starting installation, disconnect the power supply at the home main switch.

Remove the grease filter/s and the carbon filter holder.

Pre-assemble the three parts of the flue support bracket with 4 screws; the width

of the bracket

must

be identical to the internal width of the telescopic flue.

For filter version only

Pre-assemble the three parts of the deflector with 2 screws; the width

of the deflector

must be

identical to the internal width of the telescopic flue.

Place the extraction unit on a flat surface and fit the bottom part of the hood on it.

Secure it with 4 screws.

Model AKR 958 only:

Carry out the electrical connections between the two parts.

Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.

Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the

centre line drawn on the wall, and the lower edge of the hole diagram must match the lower edge of the

hood.

Remember that with installation completed the bottom of the hood must be at least 50 cm above the hob

in case of electric cookers and 75 cm in case of gas or mixed cookers.

Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two

external holes and drill, remove the hole diagram.

Insert 2 wall plugs and fix the hood support bracket with two 5x45 mm screws.

Hook the hood to the bracket.

Adjust the distance between the hood and the wall.

Adjust the hood horizontally.

10.

From the inside of the extraction unit, mark the holes for fixing the hood (to do so, remove the filter

holder; refit it after fixing the hood).

11.

Remove the hood from the bracket and drill on the mark (Ø 8 mm - see step 10). Insert 1 wall plug.

12.

Fit the flue support bracket

to the wall and against the ceiling, use the support bracket as hole diagram

(the small slot on the support must match the line drawn on the wall - step 3) and mark 2 holes with the

pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs.

13.

Fix the flue support bracket to the wall with two 5x45 mm screws.

14.

Hook the hood to the bottom bracket. Fix the hood to the wall with a 5x45mm screw (ABSOLUTELY

NECESSARY).

15.

Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar

located above the extraction motor unit.

For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter

operation, fix the deflector

to the flue support bracket

with 4 screws and connect the other end of

the exhaust pipe to the deflector collar

(if the collar is not already fitted it should be inserted on the

deflector and secured with 1 screw). Once the steam and fumes have been filtered by the carbon filter

(not provided, to be ordered separately) they are conveyed back to the kitchen through grid

16.

Carry out the electrical connection.

17.

Fit the casing on the runners.

18.

Fix the casing to the hood with 4 screws

19.

Apply the flues and fix them with 2 screws (

19a

) to the flue support

(

19b

20. Model AKR 928 only

: Carry out the electrical connections between the two parts.

21.

Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction

unit and fix it to the hood (

21a

) with 2 screws (

22b

Refit the grease filter/s and the carbon filter holder, and check for correct hood operation.

D F NL E

P I GR

31833083.fm Page 7 Friday, October 10, 2003 4:39 PM



5019 318 33083

AKR 928 - AKR 958

Control panel.

Light ON/OFF switch.

Extraction and minimum extraction speed ON/

OFF switch.

Medium extraction speed switch.

Maximum extraction speed switch.

Grease filter.

Halogen bulbs.

Steam deflector.

Telescopic flue.

To clean the grease filter

Wash the grease filter at least once a month.

Disconnect the electrical power supply.

Remove the grease filters -

Fig. 1

AKR 928

... pull the spring release handle (

) downwards,

then remove the filter.

AKR 958

... push the spring release handle backwards (

then remove the filter downwards (

After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface is

covered.

Replacing bulbs

Disconnect the electrical power supply.

Use a small screwdriver or any other suitable tool

to prise off (

m-Fig. 2

) the lamp cover (

p-Fig. 2

Remove the burnt-out bulb.

Use 20W max halogen bulbs only, taking care not

to touch them with your hands.

Close the lighting unit (snap-close).

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

Disconnect the electrical power supply.

Remove the grease filter (

Fig. 1

Turn the side knobs 90° and then remove the filter

holder (

g - Fig. 3

Fit the carbon filter (

h - Fig. 3

) in the filter holder

(

i - Fig. 3

Refit the filter holder and secure it to the hood

with the screw (

g - Fig. 3

Refit the grease filter.

Fitting the carbon filter:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible, using

a normal dishwasher detergent. To avoid particles of

food or dirt settling on the filter during washing and

giving rise to unpleasant smells, it is advisable to wash

the filter on its own. After washing, dry the filter in the

oven at 100°C for 10 minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

Fig. 1

Fig. 2

Fig. 3

AKR 928

AKR 958

AKR 928

PRODUCT SHEET

31833083.fm Page 8 Friday, October 10, 2003 4:39 PM

Whirlpool AKR 957 IX Program Chart

Brand: Whirlpool

Model: AKR 957 IX

Category: Cooker hoods

Type: Program Chart

This manual is also suitable for

Download PDF

report

Whirlpool AKR 957 IX Program Chart

This manual is also suitable for

Whirlpool AKR 957 IX Program Chart

Related papers

Other documents