Page is loading ...
5019 318 33080
AKR 948
INSTALLATIONSBLAD
Minsta tillåtna avstånd från olika typer av spisar: 50 cm (elektrisk spis), 75 cm
(gasspis, gasolspis och koleldad spis). Följ numreringen nedan för monteringen:
(1
Ö
2
Ö
3
Ö
.....). Slå inte på strömmen till fläktkåpan förrän installationen är
helt avslutad. Observera! Rökröret och rörklämmorna (15) som krävs för
installationen levereras inte tillsammans med fläktkåpan, utan måste köpas
separat.
INSTALLASJONSVEILEDNING
Minimumsavstand til komfyrtopp: 50 cm (elektriske kokeplater), 75 cm (gass-,
parafin- eller kullkomfyr). Følg nummereringen ved montering (1
Ö
2
Ö
3
Ö
.....).
Apparatet må ikke tilkobles strømnettet før installasjonen er helt avsluttet.
Merk! Avtrekksrøret og festebåndene (15) følger ikke med og må anskaffes
separat.
INSTALLATIONSVEJLEDNING
Minimumafstand fra kogezoner: 50 cm (elkogezoner), 75 cm (gas-, olie- eller
kulfyrede kogezoner). Ved montering skal man følge vejledningens
nummerrækkefølge (1
Ö
2
Ö
3
Ö
.....). Apparatet må ikke tilsluttes elforsyningen,
før installationen er fuldført. Advarsel! Aftræksrøret og spændebåndene (15)
leveres ikke med emhætten og skal købes separat.
ASENNUSOHJEET
Vähimmäisetäisyys liedestä: 50 cm (sähkölevyt), 75 cm (kaasu-, öljy- tai
hiililiedet). Suorita kokoonpano numerojärjestyksessä (1
Ö
2
Ö
3
Ö
.....). Älä
kytke liesituuletinta sähköverkkoon ennen kuin kaikki asennusvaiheet on
suoritettu. Huomaa! Poistoputkea ja kiinnittimiä (15) ei toimiteta laitteen
mukana, ne on hankittava erikseen.
INSTALLATION SHEET
Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or
coal cookers). To install, follow points (1
Ö
2
Ö
3
Ö
.....). Do not connect the
appliance to the electrical power supply until installation is completed.
Warning! The exhaust pipe and clamps (15) are not supplied and must be bought
separately.
S
N
DK
FIN
GB
31833080.fm Page 1 Friday, June 6, 2003 3:45 PM
5019 318 33080
AKR 948
31833080.fm Page 2 Friday, June 6, 2003 3:45 PM
5019 318 33080
AKR 948
Preliminary information for installing the hood:
Disconnect the power supply at the domestic main switch before carrying out electrical connections.
1. Place the extraction unit on a flat surface and fit the bottom part of the hood on it
(remove the grease filter/s).
2. Carry out the electrical connections between the two parts.
3. Fix the hood to the extraction unit with 10 screws.
4. Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.
5. Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the
centre line drawn on the wall, and the lower edge of the hole diagram must match the lower edge of the
hood: remember that with installation completed the bottom of the hood must be at least 50 cm above
the cooktop in case of electric cookers and 75 cm in case of gas or mixed cookers.
6. Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two
external holes and drill, remove the hole diagram, insert 2 wall plugs and fix the hood support bracket
with two 5x45 mm screws.
7. Hook the hood to the bracket.
8. Adjust the distance between the hood and the wall.
9. Adjust the hood horizontally.
10. From inside the hood, mark the holes for fixing the hood permanently.
11. Remove the hood from the bracket.
12. Drill on the marks (Ø 8 mm - see step 10).
13. Insert 2 wall plugs.
14. Fit the flue support bracket G to the wall and against the ceiling, use the support bracket as hole diagram
(the small slot on the support must match the line drawn on the wall - step 4) and mark 2 holes with the
pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs.
15. Fix the flue support bracket to the wall with two 5x45 mm screws.
16. Hook the hood to the bottom bracket.
17. Fix the hood to the wall with two 5x45 mm screws (ABSOLUTELY NECESSARY).
18. Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar
B located above the extraction motor unit.
For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter
operation, fix the deflector F to the flue support bracket G with 2 screws and connect the other end of
the exhaust pipe to the deflector collar F (if the collar is not already fitted it should be inserted on the
deflector and secured with 1 screw). Once the steam and fumes have been filtered by the carbon filter
(not provided, to be ordered separately) they are conveyed back to the kitchen through grid H.
19. Carry out the electrical connection.
20. Apply the flues and fix them with 2 screws (20a) to the flue support G (20b).
21. Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction
unit.
Refit the grease filter/s and check for correct hood operation.
INSTALLATION - ASSEMBLY INSTRUCTIONS
S DK FIN GB
N
31833080.fm Page 11 Friday, June 6, 2003 3:45 PM
5019 318 33080
AKR 948
1. Control panel.
2. Grease filter.
3. Halogen bulbs.
4. Steam deflector.
5. Telescopic flue.
To clean the grease filter
Wash the grease filter at least once a month.
1. Disconnect the electrical power supply.
2. Remove the grease filters - Fig. 1: pull the spring
release handle (f) downwards, then remove the
filter.
3. After cleaning the grease filter refit in reverse
order, making sure the entire extraction surface
is covered.
Carbon filter Fitting and Maintenance
Fitting the carbon filter:
1. Disconnect the electrical power supply.
2. Remove the grease filter (f - Fig. 1).
3. Turn the side knobs 90° and then remove the
filter holder (g - Fig. 2).
4. Fit the carbon filter (h - Fig. 2) in the filter
holder (i - Fig. 2).
5. Refit the filter holder and secure it to the hood
with the screw (g - Fig. 2).
6. Refit the grease filter.
Carbon filter maintenance:
Unlike traditional carbon filters, this carbon filter can
be washed and reactivated.
With normal hood use, the filter should be cleaned
once a month. The best way to clean the filter is in a
dishwasher at the highest temperature possible,
using a normal dishwasher detergent. To avoid
particles of food or dirt settling on the filter during
washing and giving rise to unpleasant smells, it is
advisable to wash the filter on its own. After
washing, dry the filter in the oven at 100° C for 10
minutes to reactivate it.
The filter will retain its odour-absorbing capacity for
three years, after which it must be replaced.
Replacing bulbs
1. Disconnect the electrical power supply.
2. Use a small screwdriver or any other suitable tool
to prise off (m-Fig. 3) the lamp cover (p-Fig. 3).
3. Remove the burnt-out bulb.
Replace using 20 W max halogen bulbs only,
making sure not to touch them with your hands.
4. Close the lighting unit (snap-close).
CONTROL PANEL
A. Light ON/OFF switch.
B. ON/OFF and speed 1 selector switch
(small amount of steam and fumes).
B+C. Speed 2 selector switch
(medium amount of steam and fumes).
B+D. Speed 3 selector switch
(large amount of steam and fumes).
Fig. 1
Fig. 4
Fig. 2
Fig. 3
PRODUCT SHEET
S DK FIN GB
N
31833080.fm Page 12 Friday, June 6, 2003 3:45 PM
/