Focal Point Seem 2 LED Wall-to-Ceiling FSM2L-CXF Installation guide

  • Hello! I've reviewed the installation instructions for the Focal Point FSM2L-CXF LED luminaire. This document details the installation process for wall to ceiling corner luminaires, emphasizing pre-drywall installation and the use of specific configurations. The guide also includes important safety information and instructions for electrical connections and handling the LED components. I am here to help you with any questions you may have about the installation process, components or any other aspect of this device.
  • When should the luminaire be installed?
    Does the installation require a qualified professional?
    What should be avoided during the installation?
    Is framing required for wall-mounted housings?
    Are specific drawings required before installation?
IS0532 Rev. G 2020 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 5
seem 2led wall to ceiling corners
FSM2L-CXF
focal point
corner units
s - start of run
c - ceiling
W - Wall
i - intermediate
e - end of run
key
poWer off
poWer on
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
attention
LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL.
configurations are run specific, please consult factory draWings before beginning installation.
flex whip
2"x6"
framing
feed
ceiling height
specified luminaire length
specified luminaire length
2"x6" framing reQuired on botH
sides of Wall mounted Housings
4.25” min
4.625” max
backer flange
(may be pre-installed
or sHipped loose)
mud flange
(sHipped loose)
parts lists
backer flange
(72001) (8-32x 3/8”
WASHER HEX HEAD SCREW)
mud flange (70005)
(8-32 x 5/16” FLAT
UNDERCUT HEAD SCREW)
included HardWare
reflector 72010)
(8-18 x 1/4 self tapping
screW)
sHipped installed
(a11623-01)
joiner bracket
assembly
(72010)
tie Wire bracket
(12547)
tie-Wire bracket
screW (72010)
(8-18 x 1/4 self tapping
screW)
lens end piece
(a08608)
lens tool
(a10554-01)
(affixed to Housing.
one per run)
joiner pin
(70058)
IS0532 Rev. G 2020 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 5
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
3a
ceiling units only
3b
4
1
5
2' - 4'
5' - 6'
7' - 8'
dryWall
tHickness orientation guide point position
3/8"1 X F
1/2"1 X E
5/8"1 X D
3/4"1 X C
7/8"1 X B
1"1 X A
11/8"1 Y G
11/4"2 Y F
13/8"2 Y E
11/2"2 Y D
15/8"2 Y C
13/4"2 Y B
17/8"2 Y A
2"2 X E
21/8"2 X D
A
X
orientation 1
orientation 2
Y
B
C
D
E
F
G
H
X
Y
backer flange placement guide
A
X
orientation 1
B
C
D
E
F
G
H
5/8
5/8" dryWall
A
X
orientation 1
B
C
D
E
F
G
H
1/2
1/2" dryWall
using tHe backer flange
placement guide from
page 1 determine tHe
proper placement of tHe
backer flange for your
dryWall tHickness.
if backer flanges Were
pre-installed skip to step 6
2
AVOID ALL CONTACT WITH LED SURFACE,
LEDs ARE EASILY DAMAGED!
IS0532 Rev. G 2020 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 5
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
9 11
11
10
8
67
corner units (c & W) installation
continue installing remaining ceiling units
11 1112
x2
13
connect flex WHip
to ceiling unit
secure ceiling
unit to structure
above
14
make electrical connection
AVOID ALL CONTACT WITH LED SURFACE,
LEDs ARE EASILY DAMAGED!
15 secure reflectors to Housing
(6 screWs per reflector)
make electrical connection
IS0532 Rev. G 2020 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 4 of 5
install remaining Wall Housings
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
make electrical connections
18
19 begin dryWall installation (ceiling units sHoWn)
20
attention
before beginning dryWall
installation consult guide on
page 2 to ensure tHe backer
flange is set at tHe correct
deptH for tHe dryWall.
16 17
24
gently slide
lens into corner
before installing
remaining lenses
25
REFERENCE INSTRUCTIONS ON INCLUDED
TOOL FOR LENS INSTALLATION.
26
install
reflectors
starting
from bottom
secure reflectors
to Housing (6 screWs
per reflector)
AVOID ALL CONTACT WITH LED SURFACE,
LEDs ARE EASILY DAMAGED!
22 23
dryWall
mud
21
dryWall
Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls
and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC
is prohibited.
IS0532 Rev. G 2020 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 5 of 5
DriVer serVice
EMERGENCY
SEE BATTERY MANUFACTURER
INSTRUCTIONS
emergency maximum mounting HeigHt:
19.00'
32
1
AVOID ALL CONTACT WITH LED SURFACE,
LEDs ARE EASILY DAMAGED!
/