SnapFence HSEK-3X52 Operating instructions

Brand
SnapFence
Model
HSEK-3X52
Category
Car kits
Type
Operating instructions
Directions for constructing your SnapFenceTM Extension Kit.
IF YOU CAN DREAM IT, YOU CAN BUILD IT.
Extension KitInstructions
1
1) Unpack box and separate parts.
2) Install desired ground attachments in your determined locations.
Typical attachments are shown, Ground Anchor Stakes** or Base Mounts (M1).
3) Install the Posts (V1) by sliding them onto the ground attachments and secure in place with screws. Secure with PVC glue if desired.
If installing a 3’ high fence as shown in the example, no cutting will be necessary
if using 39” Posts.
4) Build the Hinged Frame
Attach the Hinge Elbows (E1) to the 46” Rails (H1) for the horizontals as well as the 30” Balusters (B1) for the verticals of the frame.
Slide them into the Rails until they ‘Snap’ into place. You will want to give it a gentle tap to secure the tight fit. Build your hinged
hinged frame section before moving onto the next step. You should have (1) finished frame.
5) Slide the lower Hinge Brackets (K1) onto the 39” Posts (V1). Secure with screws.
Slide the finished hinge frames onto the Hinge Bracket (K1) Pins. Slide the upper Hinge Bracket (K1) onto the post and let the pin
gently slide into the Hinge Elbow (E1). Secure with Screws. Slide the Post Caps (C1) onto the 39” Posts (V1).
6) Finish with pre-cut Lattice SnapPanels (sold seperately) .
Continue to add to your project with the SnapFenceTM Extension Kit, (sold separately.)
V1 (2) 39” Posts
H1 (2) 46” Rails
B1 (2) 30” Balusters
E1
(4)
Hinge
Elbows
(1)
Bag of
Screws
C1
(2)
Post
Cap
M1
(2)
Base
Mounts
Part Number: HEK-3x52L
Hinged Fence Extension Kit Lattice Panel
Note: Extension Kits are designed to be added to an existing Starter Kit #HSK-3x13L
K1
(4)
Hinge
Brackets
Screw
through
back side
of lattice
panel. Slide Hinge
Bracket
onto Post.
K1
V1
Slide Hinge
Bracket
onto Post.
Base Mounts
M1
holes face upward
holes face downward
Finished
Hinged
Frame
B1 B1
H1
H1
E1
E1
E1
E1
46”
30” Hinged
Frame
x 1
H1
H1
B1
B1
52”
Slide Hinge
Bracket
onto Post.
K1
V1
Slide Hinge
Bracket
onto Post.
K1
Slide Hinge Frame
onto
Hinge Bracket.
K1
Slide Hinge Frame
onto
Hinge Bracket.
C1
Slide Hinge onto Post and
into Frame.
K1
V1
Screw
through
back side
of lattice
panel.
Visit: www.snap-
fence.com for more
How-To help. Scan the
QR code to take you
directly to useful
SnapFence tips.
Always pre-measure your opening
to be sure that you align the post and
ground mount before securing to
ground surface. May not always align
exactly to 52” depending on ground
surface.
  • Page 1 1

SnapFence HSEK-3X52 Operating instructions

Brand
SnapFence
Model
HSEK-3X52
Category
Car kits
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents