SnapFence BSEK-3X4 Operating instructions

Brand
SnapFence
Model
BSEK-3X4
Type
Operating instructions
Directions for constructing your SnapFenceTM Sign Kit.
IF YOU CAN DREAM IT, YOU CAN BUILD IT.
Extension Kit
Instructions
1
(2) 46” Post/Rails (4)
Rail
Connectors
(1)
Bag of
Screws
Secure with PVC glue if desired.
Part Number: BSEK-3x4
3’ x 4’ Banner Sign Extension Kit (Expandable to 5’)
(2)
Anchor
Stakes
Visit: www.snapfence.com for more
How-To help. Scan the QR code to take
you directly to useful SnapFence tips.
(2) 12” Rails for
Expansion (2)
Couplers
(2)
Base
Mounts
**Not all parts included will be needed depending upon desired surface mount. Some parts may be left over.
Cut to size if smaller sizes
are needed.
Suggested methods for
securing your banner/sign to
face of frame:
Use self-tapping screws
through grommet holes.
Use velcro along the back
side of the sign.
Use zip-ties secured through
the grommet holes and then
around the frame.
1
2
3
3
Securing your banner using
pockets:
Slide the Rails into the pockets
before you attach your Elbows
and your Rail Connectors.
The Rails will remain
fully adjustable up and down
until you secure using self-tapping
screws.
Banner/Sign Attachments:
See suggested methods
Affix Banner/Sign
(Front and/or Back)
(2) 39” Post/Rails
(2)
Post
Cap
Note: Extension Kits are designed to be added to an existing Starter Kit #BSK-3x4
Soil Mount:
2) Drive anchor stake at 48” from center of installed
SnapFenceTM post to center of post to be added.
Soil
48”
Attach post to
anchor stake
with screws.
Solid
48”
Secure base with larger
screws/bolts as needed.
OR
Anchor stakes
sold separately.
Solid Mount:
2) Measure 48” from center of installed SnapFenceTM post to
center of post to be added.
Attach post to base mount with screws. Secure base mount to existing
solid surface using holes provided.
Note - use a larger type of screw or bolt as needed to secure to solid surfaces. Or
leave free-standing.
To extend the Post/Rails add the
Coupler and the 12” Post/Rail
Extension. Gently tap into place.
Direct: 888-959-4471
Affix Banner/Sign
to face of frame.
1
2
Affix Banner/Sign
using a pocket.
3) Attach Rail Connectors to each end of the top and bottom Rail (46”).
Gently tap into place. To extend your project size, add the coupler and 12” post/rail
section.
4) Snap rail sections onto (39”) posts. Measure and move rail to desired level. Secure
with screws on both ends.
5) Push on post caps. And affix your banner/sign.
Continue to add to your project with the SnapFenceTM Extension Kits.
Banners and signs can be affixed to the frame with various fasteners.
See recommendatons in sidebar. Explore and make it your own!
Secure with screws
on both ends.
1) Unpack box and separate parts.
Measure and move
rails to desired levels.
>You will have (1) 39” Post, (1) Base Mount & (1) Post Cap leftover
if using with a pre-existing SnapFence system.
  • Page 1 1

SnapFence BSEK-3X4 Operating instructions

Brand
SnapFence
Model
BSEK-3X4
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents