DMP Electronics CellCom SLC User manual

Brand: DMP Electronics

Model: CellCom SLC

Type: User manual

This manual is also suitable for

IComsl

™

serIes UnIversal

larm CommUnIC

tor

InstallatIon and programmIng guIde

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’s

authority to operate the equipment.

If necessary, the installer should consult the dealer or an experienced radio/television technician for additional

suggestions.Theinstallermayndthefollowingbooklet,preparedbytheFederalCommunicationsCommission,

helpful:

“How to identify and Resolve Radio-TV Interference Problems.”

ThisbookletisavailablefromtheU.S.GovernmentPrintingOfce,WashingtonD.C.20402

StockNo.004-000-00345-4

©2014DigitalMonitoringProducts,Inc.

InformationfurnishedbyDMPisbelievedtobeaccurateandreliable.

This information is subject to change without notice.

Theantenna(s)usedforthistransmittermustbeinstalledtoprovideaseparationdistanceofatleast20cmfrom

all persons.

THISDEVICECOMPLIESWITHPART15OFTHEFCCRULES.OPERATIONISSUBJECTTOTHEFOLLOWINGTWO

CONDITIONS:(1)THISDEVICEMAYNOTCAUSEHARMFULINTERFERENCE,AND(2)THISDEVICEMUSTACCEPTANY

INTERFERENCERECEIVED,INCLUDINGINTERFERENCETHATMAYCAUSEUNDESIREDOPERATION.

Industry Canada

ThisdevicecomplieswithIndustryCanadalicense-exemptRSSstandard(s).Operationissubjecttothefollowing

twoconditions:(1)thisdevicemaynotcauseinterference,and(2)thisdevicemustacceptanyinterference,

including interference that may cause undesired operation of the device.

LeprésentappareilestconformeauxCNRd’IndustrieCanadaapplicablesauxappareilsradioexemptsde

licence.L’exploitationestautoriséeauxdeuxconditionssuivantes:(1)l’appareilnedoitpasproduirede

brouillage,et(2)l’utilisateurdel’appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesile

brouillageestsusceptibled’encompromettrelefonctionnement.

Caution Notes

Throughoutthisguideyouwillseecautionnotescontaininginformationyouneedtoknowwheninstalling

the

ommunicator.Thesecautionsareindicatedwithayieldsign.Wheneveryouseeacautionnote,make

sure you completely read and understand its information. Failing to follow the caution note can cause

damage to the equipment or improper operation of one or more components in the system.

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

iii

Table of ConTenTs

Table of Contents

Description .......................................................................................................................1

What is Included ............................................................................................................... 1

System Components ............................................................................. 1

1.1 Terminals (J9) ........................................................................................................1

1.2 Programming Connection ........................................................................................ 2

1.4 Tamper .................................................................................................................. 2

1.5 Reset Button ..........................................................................................................2

1.6 Load Button ...........................................................................................................2

1.7 Backlit Logo ........................................................................................................... 2

Mounting the iComSL Series Communicator ......................................... 3

2.1 Selecting a Location ............................................................................................... 3

Applications ...........................................................................................4

3.1 CID

Dialer Connection ..............................................................................................4

3.2 Zones 1 - 4 Input Connection .................................................................................. 4

3.3 Zone 4 Bell Connection ........................................................................................... 5

Remote Arming/Disarming ................................................................... 6

4.1 DMP Virtual Keypad App / Virtual Keypad Browser ....................................................6

Programming the

iComSL

Series Universal Alarm Communicator ........ 7

5.1 Before You Begin ...................................................................................................7

5.2 Getting Started ......................................................................................................7

5.3 Programming Menu ................................................................................................ 7

5.4 Reset Timeout .......................................................................................................7

5.5 Special Keys ........................................................................................................... 8

5.6 Entering Alpha Characters .......................................................................................8

5.7 Entering Non-Alpha Characters ................................................................................ 9

5.8 Keypad Displays Current Programming.....................................................................9

Initialization ........................................................................................10

6.1 Initialization ..........................................................................................................10

6.2 Clear All Codes ......................................................................................................10

6.3 Clear All Schedules ................................................................................................10

6.4 Clear Events .........................................................................................................10

6.5 Clear Zone Programming .......................................................................................10

6.6 Clear Communication ............................................................................................10

6.7 Set to Factory Defaults ..........................................................................................10

Communication ................................................................................... 11

7.1 Communication .....................................................................................................11

7.2 Account Number ...................................................................................................11

7.3 Transmission Delay ................................................................................................11

7.4 Communication Type .............................................................................................11

7.5 Test Time .............................................................................................................11

7.6 Test Days .............................................................................................................11

7.7 Check-in Minutes ...................................................................................................11

7.8 Fail Time ..............................................................................................................11

7.9 Receiver 1 Programming ........................................................................................11

7.10 Alarm Reports .......................................................................................................11

7.11 Supervisory/Trouble Reports ..................................................................................11

7.12 Opening/Closing and User Reports .........................................................................11

7.13 Test Report ...........................................................................................................11

7.14 First IP Address .....................................................................................................11

7.15 First IP Port ..........................................................................................................11

7.16 Second IP Address ................................................................................................12

7.17 Second IP Port ......................................................................................................12

7.18 Receiver 2 Programming ........................................................................................12

7.19 Alarm Reports .......................................................................................................12

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guideiv

Table of ConTenTs

7.20 Supervisory/Trouble Reports ..................................................................................12

7.21 Opening/Closing and User Reports .........................................................................12

7.22 Test Report ...........................................................................................................12

7.23 First IP Address .....................................................................................................12

7.24 First IP Port ..........................................................................................................12

7.25 Second IP Address ................................................................................................12

7.26 Second IP Port ......................................................................................................12

Messaging Setup ................................................................................. 13

8.1 Messaging Setup ...................................................................................................13

8.2 Enable Messaging .................................................................................................13

8.3 System Name .......................................................................................................13

8.4 Destination 1 ........................................................................................................13

8.5 Destination 1 User Number ....................................................................................13

8.6 Destination 2 ........................................................................................................13

8.7 Destination 2 User Number ....................................................................................13

8.8 Destination 3 ........................................................................................................13

8.9 Destination 3 User Number ....................................................................................13

8.10 O/C Email .............................................................................................................13

8.11 Monthly Limit ........................................................................................................13

8.12 SMTP Server .........................................................................................................14

8.13 SMTP Server Port ..................................................................................................14

8.14 SMTP Username ....................................................................................................14

8.15 SMTP Password .....................................................................................................14

8.16 From Email Address ...............................................................................................14

Remote Options ..................................................................................15

9.1 Remote Options ....................................................................................................15

9.2 Remote Key ..........................................................................................................15

9.3 Remote Disarm .....................................................................................................15

System Reports ...................................................................................15

10.1 System Reports .....................................................................................................15

10.2 Opening/Closing Reports .......................................................................................15

10.3 Zone Restoral Reports ...........................................................................................15

System Options ................................................................................... 15

11.1 System Options .....................................................................................................15

11.2 Entry Delay 1 ........................................................................................................15

11.3 Exit Delay .............................................................................................................15

11.4 Cross Zone Time ...................................................................................................15

11.5 Power Fail Delay ....................................................................................................16

11.6 Swinger Bypass Trips .............................................................................................16

11.7 Reset Swinger Bypass ............................................................................................16

11.8 Time Changes .......................................................................................................16

11.9 Keypad Input ........................................................................................................16

Output Options ....................................................................................17

12.1 Output Options .....................................................................................................17

12.2 Cutoff Outputs ......................................................................................................17

12.2.1 Output Cutoff Time ...............................................................................................17

12.3 Communication Failure Output ...............................................................................17

12.4 Armed Output .......................................................................................................17

12.5 Remote Arming Output ..........................................................................................17

12.6 Heat Saver Temperature (

iComSL

CZ only) ...............................................................17

12.7 Cool Saver Temperature (

iComSL

CZ only) ...............................................................17

Area Information .................................................................................17

13.1 Area Information ...................................................................................................17

13.2 Area Number ........................................................................................................17

13.3 Area Name ...........................................................................................................17

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

Table of ConTenTs

13.4 Automatic Arming .................................................................................................18

13.4.1 Bad Zones ............................................................................................................18

13.5 Automatic Disarming .............................................................................................18

Zone Information ................................................................................18

14.1 Zone Information ..................................................................................................18

14.2 Zone Number ........................................................................................................18

14.3 Zone Name ...........................................................................................................18

14.4 Zone Type ............................................................................................................18

14.5 Area Assignment ...................................................................................................18

14.6 Arming Zone Assignment .......................................................................................19

14.7 Style ....................................................................................................................19

14.8 Next Zone .............................................................................................................19

14.9 Alarm Action .........................................................................................................19

14.10 Disarmed Open .....................................................................................................19

14.11 Message To Transmit .............................................................................................19

14.12 Output Number .....................................................................................................20

14.13 Output Action .......................................................................................................20

14.14 Swinger Bypass .....................................................................................................20

14.15 Cross Zone ...........................................................................................................20

14.16 Receiver Routing ...................................................................................................20

14.17 Zone Number ........................................................................................................20

Stop .....................................................................................................21

15.1 Stop .....................................................................................................................21

Set Lockout Code ................................................................................21

16.1 Set Lockout Code ..................................................................................................21

Z-Wave Setup ......................................................................................22

17.1 Add Z-Wave Devices (ADD) ....................................................................................22

17.2 List Z-Wave Devices (LIST) ....................................................................................22

17.3 RENAME Z-Wave Devices .......................................................................................22

17.4 STATUS of Z-Wave Devices ....................................................................................23

17.5 Remove Z-Wave Devices (REMOVE) ........................................................................23

17.6 Favorites (FAV) .....................................................................................................23

17.7 Adding a FAVORITE ...............................................................................................23

17.8 ADD Devices to FAVORITES ...................................................................................24

17.9 Device Settings in FAVORITES ................................................................................24

17.10 EDIT Devices in FAVORITES ...................................................................................25

17.11 REMOVE Devices from FAVORITES .........................................................................25

17.12 Transfer Controller (XFER) .....................................................................................25

17.13 Optimize (OPT) .....................................................................................................26

Appendix .............................................................................................27

18.1 False Alarm Reduction ...........................................................................................27

System Recently Armed report ...............................................................................27

18.2 Diagnostics Function .............................................................................................27

Panel Settings .......................................................................................................27

Serial Number ......................................................................................................27

Model Number ......................................................................................................27

Firmware Version ..................................................................................................27

Z-Wave Test Option ...............................................................................................27

Contact ID Recvd ..................................................................................................27

Exiting the Diagnostics program .............................................................................27

18.3 Using the 984 Command Function ..........................................................................27

18.4 Using the Walk Test ...............................................................................................27

Walk Test..............................................................................................................27

Trip Counter for Walk Test (STD) ............................................................................27

Test End Warning ..................................................................................................27

Failed Zones Display ..............................................................................................28

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guidevi

Table of ConTenTs

18.5 Cross Zoning .........................................................................................................28

18.6 Z-Wave Information ...............................................................................................28

18.7 Zone 4 Bell Cadence Information ............................................................................28

Remote Arming/Disarming for Ademco Vista Control Panels .................................................29

Ademco Vista 20P to iComSL .............................................................................................30

DMP XRSuper6 to iComSL .................................................................................................30

Ademco Vista 20P ECP to iComSL ......................................................................................31

Specications ......................................................................................32

Ordering Information ..........................................................................32

Certications .......................................................................................32

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

IntroductIon

iComSL™ Series Universal Alarm Communicator

Description

The

iComSL

™SeriesAlarmCommunicatorprovidesafullysupervisedalarmcommunicationpathforanyburglary

orresidentialrecontrolpanel.TheiComSLSeriescanbeconnectedtoacontrolpanel’sdialeroutputand

usedtocaptureContactIDmessagesbased on SIA DC-05-1999.09-DCS.TheiComSLChasabuilt-inethernet

porttoconnecttoanetworkandsendmessagestoDMPModelSCS-1RorSCS-VRCentralStationReceivers.

The

ommunicator also provides four input zones and two open-collector outputs for connection to burglary or

residentialrecontrolpaneloutputsandzones.TheiComSLSeriesCommunicatorZone4allowsaconnection

to the bell output of an existing burglary control panel. The communicator operates in a variety of applications:

CIDDialerConnection,Zones1-4InputConnections,orZone4BellConnection(SeeApplicationsonpage5).The

iComSL

CZ™AlarmCommunicatorincludesanonboardZ-Wavecontrollerforhomeautomationapplications.

What is Included

The

iComSL

SeriesUniversalAlarmCommunicatorincludesthefollowing:

• PCBwithEnclosure

• HardwarePack

System Components

1.1 Terminals (J9)

Power Connection Terminals

PowerisprovidedfromtheNominal12Vdcauxiliaryoutputoftheburglarycontrolpanel.

OBSERVEPOLARITY(SeeFigure1andBacklitLogo)

Using18-22AWGwire,connectthe

communicator

terminal+12tothepositiveterminalonthe

control panel

auxiliary output

ConnectthecommunicatorterminalG(Ground)tothenegativeterminalonthecontrolpanelauxiliaryoutput.

Control Panel Standby Power

Duringapoweroutage,theiComSLdrawspowerfromthecontrolpanel’sbackupbattery.TheiComSLmustbe

included in the standby battery calculations for the control panel.

Zones 1-4

TerminalsZ1toZ3,G(Ground),Z4+andZ4-providefourzonestoconnecttoindividualrelayoutputson

thecontrolpanel.Zone4(Z4+andZ4-)canbeconnectedtothecontrolpanelbelloutput.SeeZone4Bell

Connection.

Figure 1: iComSL Series Communicator

RESET

LOAD

system components

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guide

system components

Open-Collector Outputs

Thetwooutputs,terminalsO1andO2(seeFigure1),canbeprogrammedtoindicatetheactivityofthezones

orconditionsoccurringonthesystem.Open-Collectoroutputsdonotprovideavoltagebutinsteadswitch-to-

groundthevoltagefromanothersource.Maximumvoltageis30Vdc@50mA.Theoutputscanrespondtoanyof

the conditions listed below:

1) Activationbyzonecondition:Steady,Pulse,Momentary,orFollow

2) Communication

3) Armedareaannunciation

4) RemoteArmingOutput

Dialer Connection

Directlyconnectthetelcophoneline(tipandring)fromthecontrolpaneltotheiComSLSeriesUniversal

CommunicatorterminalR(Ring)andoneintoT(Tip)(SeeCIDDialerConnection).

1.2 Programming Connection

A4-pinheader(PROG)isprovidedtoconnectakeypadwhenusingaDMP

Model330ProgrammingCable.Thisprovidesaquickandeasyconnection

for programming the

iComSL

SeriesUniversalAlarmCommunicator.After

programmingiscomplete,removethekeypad.

1.4 Tamper

ThetamperbuttonispressedwhenthecoveroftheiComSLSeries

Communicatorissecuredontotheenclosure.Whenthecoverisremoved,the

communicatorsendsaTamperTroublemessagetotheCentralStation.

1.5 Reset Button

The Reset button is located on the right side of the circuit board and is used to

resetthecommunicatormicroprocessor.Afterresettingthe

communicator,

begin

programmingwithin30minutes.Ifyouwaitlongerthan30minutes,resetthe

communicator

again.

1.6 Load Button

The

iComSL

SeriesUniversalAlarmCommunicatorsoftwarecanbeupdated

viatheprogramming(PROG)header.Toupdatethecommunicatorwithanew

software version, complete the following steps at the protected premise:

1. ConnectaDMP399CablefromtheProgrammingHeadertotheserialportof

yourPCoperatingRemoteLinkandcontainingthecommunicatorRUle.

2. StartRemoteLinkandcreateoropentheaccountthatmatchesthe

communicator to be updated.

3. SettheConnectionInformationTypetoDirectwithabaudrateof38400and

choosetheappropriateCOMport.

4. SelectPanel>RemoteUpdate,thenselectthecorrectRUleforthe

communicator.

5. PressandholdtheLOADbutton,thenpressandreleasetheRESETbutton.

6. ReleasetheLOADbuttonandclick<Update>inRemoteLink.

7. Afterthesoftwareupdateiscompleted,removethe399cableandpresstheRESETbuttontoresumenormal

operation.

1.7 Backlit Logo

ThebacklitlogoindicatesthePowerandArmedstatusofthecommunicator.Dependingontheoperation,the

LEDdisplaysinRedorGreenaslistedinthetable.TheLEDindicatesthestatusofthesystembatteryand

primary power.

Color and Activity Operation

GreenSteady CommunicatorDisarmed,PrimaryPowerOK,BatteryOK

GreenBlinking CommunicatorDisarmed,PrimaryPowerOK,BatteryFault

NoLight CommunicatorDisarmed,PrimaryPowerFault,BatteryOK

RedSteady CommunicatorArmed,PrimaryPowerOK,BatteryOK

Red/GreenAlternate CommunicatorArmed,PrimaryPowerOK,BatteryFault

RedBlinking CommunicatorArmed,PrimaryPowerFault,BatteryOK

RESET

LOAD

Figure 2: PROG Port Location

RESET

LOAD

Figure 3: Tamper Location

RESET

LOAD

Figure 4: Reset and Load

Button Location

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

Mounting the iComSL Series Communicator

2.1 Selecting a Location

Install the communicator away from metal objects. DO NOT MOUNT THE iCOMSL SERIES COMMUNICATOR INSIDE

OR ON A CONTROL PANEL METAL ENCLOSURE (SeeFigure5).

Control Panel

Metal Enclosure

Figure 5: Suggested Mounting Locations

Figure 6: Mounting Screw Locations

Mounting Screw Locations

RESET

LOAD

Figure 7: Wire Routing Options

RESET

LOAD

RESET

LOAD

MountingthecommunicatoronornearmetalsurfacesimpairsZ-Wavewirelessperformance.Theenclosurefor

the

ommunicatorshouldbemountedusingtheprovided#6screwsinthefourmountingholes(SeeFigure6).

Mounttheenclosureinasecure,dryplacetoprotectthecommunicatorfromdamageduetotamperingorthe

elements. It is not necessary to remove the PCB when installing the enclosure.

Wheninstallingcomponentwires,caremustbetakentorouteallwiresinsuchamannerthattheywillnot

interferewiththeTamperswitch(SeeFigure7).

InstallatIon

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guide

Applications

TheiComSLSeriesCommunicatorcanbeusedinavarietyofapplications:

3.1 CID

Dialer Connection

Directlyconnectthetelcophoneline(tipandring)fromthecontrolpaneltotheiComSLtocaptureContact

IDmessagesthatarebasedontheSIAcommunicationstandardDC-05-1999.09-DCS. These messages are

thenformattedintoaSerial3messageandsenttoaDMPModelSCS-1RorSCS-VRReceiver.Note:CIDDialer

ConnectioncannotbeusedwhenusingZone4BellConnection.

Figure 8: iComSL Series Wiring Diagram for Tip and Ring Connection

Use 18-22 AWG for

Power Supply connection

Z3 +

Z4 +

Z4 -

GND

12 VDC Aux. Output

Ground

Control Panel

The panel or separate power

supply must be 12 Volt Regulated

and Power Limited.

Z1 +

Z2 +

RESET

LOAD

BAT

PROG

+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1

Normally Open

Common

Normally Closed

Normally Open

Common

Normally Closed

Normally Open

Common

Normally Closed

Normally Open

Common

Normally Closed

J26

1k ohm

MODEL

iComSLC

Figure 9: iComSL Series Wiring Diagram for Zones 1 - 4

Use 18-22 AWG for

Power Supply connection

CONTROL PANEL TIP

CONTROL PANEL RING

12 VDC Aux. Output +

Ground

Control Panel

The panel or separate power

supply must be 12 Volt Regulated

and Power Limited.

Telephone

Jack

Connector

BELL -

BELL +

RESET

LOAD

BAT

PROG

+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1

J26

MODEL

iComSLC

3.2 Zones 1 - 4 Input Connection

ConnecteachburglarycontrolpanelrelayoutputtoaiComSLSeriesCommunicatorzone.Forprogramming

purposes,thezonenumbersare1-4.(SeeFigure9forwiringdetails).Anexampleofhowyoumightusethis

application:Youcanuseanormallyclosedoutputontheburglarycontrolpaneltoindicateaburglaryalarm.The

iComSLzoneshouldbeprogrammedwithazonenameandzonetypeofBurg.Whentheoutputonthecontrol

panelturnsonandtripstheiComSLzone,amessagewillbesenttoanSCS-1RorSCS-VRreceiveratCentral

Station.Youcouldusethezonenameprogrammingtodescribewhichcontrolpanelzoneindicatedaburglary.

Note:Zone4canonlybeusedasastandardinputzonewhennotprogrammedaszonetypeAuxiliary2(A2).See

Zone4BellConnection.

applIcatIons

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

applIcatIons

3.3 Zone 4 Bell Connection

Zone4(Z4+andZ4-)canbeconnectedtothecontrolpanelbelloutput.Thiszonedetectsanalarmcondition

onthecontrolpanelbymonitoringthevoltageandcadencetimingofthebelloutput.SeeZone4BellCadence

InformationintheAppendixforcadencetiming.Toenablealarmdetectionoperation,Zone4BellConnection

mustbeprogrammedasZoneType(A2)inZoneInformationprogramming.ThetypeofCadencesenttothe

iComSLCommunicator,theZoneNumber,andtypeofmessagesenttotheSCS-1RorSCS-VRreceiverarelisted

below:

BELL CADENCE ZONE NUMBER TYPE OF MESSAGE

Steady ZONE 4 BURGLARY

Pulse or Temporal 3 ZONE 5 FIRE

Temporal 4 ZONE 6 EMERGENCY OR

CARBON MONOXIDE

Note:Zone5and6areautomaticallygeneratedbytheiComSL,usingZone4’sZonenametosendtotheCentral

Station.Zones5and6cannotbepreprogrammedinZoneInformation.

Note:CIDDialerConnectioncannotbeusedwhenusingZone4BellConnection.

Use 18-22 AWG for

Power Supply

connection

Z4 +

Z4 -

DMP Panel

MODEL iComSL

PROG

+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1

12 Vdc Aux. Output

BELL -

12 Vdc BELL +

Use 18-22 AWG for

Power Supply

connection

Z4 +

Z4 -

ADEMCO Panel

MODEL iComSL

PROG

+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1

12 Vdc Aux. Output

BELL -

12 Vdc BELL +

Use 18-22 AWG for

Power Supply

connection

Z4 +

Z4 -

NAPCO Panel

MODEL iComSL

PROG

+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1

12 Vdc Aux. Output

BELL -

12 Vdc BELL +

Use 18-22 AWG for

Power Supply

connection

Z4 -

DSC Panel

MODEL iComSL

PROG

+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1

12 Vdc Aux. Output

BELL -

12 Vdc BELL +

10k ohm

1k ohm

2.2k

ohm

Program Zone 4

DO - Alarm

AO - Alarm

Voltages above 1.4 Vdc

are considered Alarm

Voltages above 1.4 Vdc

are considered Alarm

Voltages above 1.4 Vdc

are considered Alarm

Voltages below 0.7 Vdc

are considered Alarm

Figure 10: Zone 4 Bell Connection

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guide

Remote Arming/Disarming

4.1 DMP Virtual Keypad App / Virtual Keypad Browser

UsingaSmartphonewiththeDMPVirtualKeypadApporusingacomputerwiththeVirtualKeypadBrowser

(www.myvirtualkeypad.com),youcanconnecttotheiComSLSeriesCommunicatortoarmAreas,turnOutputs

onandoff,andadd,editorremoveUsers.WhenusingtheiComSLCZ,youcancontrolZ-Wavedevices,Favorites

and Rooms.

Use 18-22 AWG for

Power Supply connection

12 Vdc Aux. Output

Control Panel

BAT

MODEL iComSL

PROG

+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1

GND

Zone 1

Zone 2

Control Panel EOL resistor

Figure 11: Virtual Keypad Application can be used to access the iComSL Series Communicator.

Figure 12: Burglary control panel zones connected to the iComSL outputs

to arm and disarm the burglary control panel.

AburglarycontrolpanelzonemaybeprogrammedasanarmingzoneandconnectedtoaiComSLoutput(O1or

O2)(SeeFigure12).ProgramtheoutputnumberinArmedOutputorRemoteArmingOutputinOutputOptions

oftheiComSL(See12.4ArmedOutputor12.5RemoteArmingOutput).TheIComSLCommunicatoroutput

connectionscanbeusedwithanyoftheapplicationslistedinApplicationsSection.

remote armIng/dIsarmIng

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

Programming the

iComSL

Series Universal Alarm Communicator

5.1 Before You Begin

Before starting to program, we recommend you read through the contents of this guide. The information in this

documentallowsyoutoquicklylearntheprogrammingoptionsandoperationalcapabilitiesofthe

iComSL

Series

UniversalAlarmCommunicator.

AfterthisIntroduction,theremainingsectionsdescribethefunctionsofeachprogrammingmenuitemsalong

with their available options. The

communicator

contains all of its programming information in an on-board

processor and does not require an external programmer.

In addition to this manual, you should also be familiar with the following

documents:

• iComSL

SeriesUniversalAlarmCommunicatorUserSheet(LT-1349)

• iComSL

SeriesUniversalAlarmCommunicatorProgrammingSheet(LT-1411)

Programming Information Sheet

Included with each communicatoraretheProgrammingSheets.Thesesheetslistthevariousoptionsavailable

for programming the

communicator

.Beforestarting,completelylloutthesheetswiththeprogrammingoptions

you intend to enter into the

communicator

Having completed the programming sheets available while entering data helps to prevent errors and can shorten

the length of time you spend programming. Completed sheets also provide you with an accurate account of the

communicator

’sprogramyoucankeeponleforfuturesystemserviceorexpansion.

The remainder of the Introduction explains starting and ending a programming session.

5.2 Getting Started

Initializing the

iComSL

Series

Whenprogramminga

communicator

forthersttimeorrewritingtheentireprogramofanexisting

communicator, use the Initialization functiondescribedinSection6.Initializingclearsthecommunicator’s

memoryofanyolddataandsetsthehighestnumberedusernumbertousercode99.

Accessing the Programmer

To access the programmer function of the

communicator

1. ConnectthekeypadtothePROGheader

2. Press and release the reset button.

3. Enterthecode6653(PROG).

4. Thekeypaddisplays:PROGRAMMER.

5.3 Programming Menu

Youarenowreadytostartprogrammingthe

iComSL

SeriesUniversalAlarmCommunicator.PressingtheCOMMAND

keyscrollsyouthroughtheprogrammingmenuitemslistedbelow.

Menu Item Section in This Manual Menu Item Section in This Manual

Initialization 6 Output Options 12

Communication 7 Area Information 13

Messaging Setup 8 Zone Information 14

Remote Options 9

Stop

System Reports 10 Set Lockout Code 16

System Options 11

Toselectasectionforprogramming,pressanySelectkeywhenthenameofthatsectiondisplaysonthekeypad.

The detailed instructions for each programming step are found in this guide.

5.4 Reset Timeout

The

iComSL

SeriesUniversalAlarmCommunicatorhasafeaturethatrequiresyoutoentertheProgrammerwithin

30minutesofresettingthecommunicator.After30minutes,ifyouattempttoprogrambyenteringthe6653

(PROG)code,thekeypaddisplays:RESET PANEL.Youmustresetthe

communicator

and enter the program code

withinthenext30minutes.

IfyouarealreadyintheProgrammeranddonotpressanykeysontheprogrammingkeypadfor30minutes,the

communicator

terminatesprogramming.Alldataentereduptothatpointissavedinthecommunicatormemory.

Using the STOP function disarms all areas:Toexitthecommunicator’sProgrammeryoumustusetheSTOP

function. The STOP optionisthesecondtothelastoptioninprogramming.TheStopfunctiondisarmsallareas.

TheprogrammingsessionisthenterminatedandthekeypadreturnstotheStatusListorMainScreen.

programmIng

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guide

programmIng

5.5 Special Keys

Thefollowingspecialkeys/areasarecommontoallDMPkeypads.

COMMAND (CMD) Key

PressingtheCOMMANDkeyallowsyoutogoforwardthroughtheprogrammingmenuandthrougheachstepofa

programmingsection.Asyougothroughtheprogramming,thekeypaddisplayshowsanycurrentprogramming

alreadystoredinthecommunicatormemory.Ifnochangeisrequiredforanoption,presstheCOMMANDkeyto

advance to the next step.

TheCOMMANDkeyisalsousedtoenterinformationintothecommunicator’smemorysuchasanIPaddressor

zonenames.PresstheCOMMANDkeyafterenteringinformation.

Back Arrow (<—) Key

UsetheBackArrowkeytobackuponestepwhileprogramming.TheBackArrowkeyisalsousedwhenanerroris

madewhileenteringinformation.PresstheBackArrowkeyoncetoerasethelastcharacterentered.

Select Keys/Areas

ThetoprowofkeysarecalledtheSelectkeysonThinline,andAqualitekeypadsorSelectAreasonGraphic

Touchscreenkeypads.EachtimeyouneedtopressaSelectkey,thekeypaddisplaysthefunctionoroptions

aboveoneofthekeysorintheSelectArea.DisplayingchoicesaboveindividualSelectkeysorinSelectAreas

allowsthemtobeusedformanydifferentapplications.Forexample,youcanenterAMorPMwhenprogramming

the automatic test time or answer YES or NO for a system option.

Duringprogramming,theSelectkeys/areasalsoallowyoutochangeinformationcurrentlyincommunicator

memorybypressingtheappropriateSelectkeyunderoronthedisplay.Youthenenterthenewinformationusing

thekeypaddataentrydigitkeys.

Whentherearemorethanfourresponseoptionsavailable,presstheCOMMANDkeytodisplaythenextoneto

fouroptions.PressingtheBackArrowkeyallowsyoutoreviewthepreviousfourchoices.

TheSelectkeys/areasarealsousedforchoosingasectionfromtheprogrammingmenu.PressanySelectkeyor

touchtheSelectAreawhentheprogrammingsectionnameyouwantdisplays.

On Thinline and Aqualite keypads,wheninstructedtopresstherstSelectkey,pressthefarleftSelectkey;

thesecondSelectkeyisthesecondfromtheleft;thirdSelectkeyissecondfromtheright;andthefourthSelect

keyisthefarrightkey.SeeFigure13.

On Graphic Touchscreen Keypads,wheninstructedtopresstherstSelectkey,touchSelectArea1;thesecond

SelectkeytouchSelectArea2;thirdSelectkeytouchSelectArea3;andthefourthSelectkeytouchSelect

Area4.SeeFigure14.

5.6 Entering Alpha Characters

Someoptionsduringprogrammingrequireyoutoenteralphacharacters.Toenteranalphacharacter,pressor

touchthekeythathasthatletterwrittenbelowit.Thekeypaddisplaysthenumberdigitofthekey.Next,press

theSelectkey/areathatcorrespondstothelocationoftheletterunderthekey.PressingadifferentSelectkey/

areachangestheletter.Whenanotherdigitkeyispressed,thelastletterdisplayedisretainedandtheprocess

starts over.

Figure 13: Thinline/Aqualite Select Keys Figure 14: Graphic Touchscreen Select Areas

First Letter

Second Letter

Third Letter

Special Character

(CBA

32-Character Display

Select Area 1

Select Area 3

Select Area 2

Select Area 4

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

programmIng

5.7 Entering Non-Alpha Characters

Toenteraspaceinanalphaentry,pressthe9digitkeyfollowedbythethirdSelectkey/area.Thethree

charactersonthe9digitkeyareY,Z,andspace.Youcanalsoenterthefollowingcharacters:–(dash),.(period),

*(asterisk),and#(poundsign)usingthe0(zero)keyandthefourSelectkeys/areasfromlefttoright.For

example,toentera–(dash),pressthe0(zero)keyandthentheleftSelectkey/area.Adashnowappearsinthe

keypaddisplay.ThetablebelowshowsthecharacterlocationsforDMPkeypads.

Key Number Select Key 1 Select Key 2 Select Key 3 Select Key 4

1 A B C (

2 D E F )

3 G H I !

4 J K L ?

5 M N O /

6 P

R &

7 S T U @

8 V W X ,

9 Y Z space _

0 - . * #

5.8 Keypad Displays Current Programming

Eachprogrammingpromptdisplayedatthekeypadshowsthecurrentlyselectedoptioninthecommunicator

memory.Theseoptionsareeithershownasanumber,ablank,oraNO or YES.Tochangeanumberorblanktoa

newnumber,pressanytoprowSelectkeyortouchanySelectArea.Thecurrentoptionisreplacedwithadash.

Pressthenumber(s)onthekeypadyouwanttoenterasthenewnumberforthatprompt.Itisnotnecessaryto

enternumberswithleadingzeros.Thecommunicatorautomaticallyrightjustiesthenumberwhenyoupress

theCOMMANDkey.

To change a programming prompt that requires a NO or YESresponse,presstheSelectkeyortouchtheSelect

Areafortheresponsenotselected.

For example, if the current prompt is selected as YES and you want to change it to NO,onThinlineorAqualite

keypadspressthethirdtoprowSelectkey.OnGraphicTouchscreenkeypadstouchSelectArea3.Thedisplay

changes to NO.PresstheCOMMANDkeytodisplaythenextprompt.

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guide

Initialization

6.1 Initialization

This function allows you to set the communicator’sprogrammedmemorybacktothe

factory defaults in preparation for system programming.

AfteryouselectYEStoclearasectionofmemory,thecommunicatorasksifyouaresure

you want to clear the memory. This is a safeguard against accidently erasing part of your

programming.NomemoryisclearedfromtheprogramminguntilyouanswerYEStothe

SURE?YES NOprompt.

6.2 Clear All Codes

NOleavesexistingcodesintact.

YESclearstheusercodememoryandassignstheusercodenumber99touser20.

6.3 Clear All Schedules

NO -Leavesexistingschedulesintact.

YES - Clears all schedules from the programming.

6.4 Clear Events

NO leaves existing event memory intact.

YES clears all event memory currently held in the communicator’sDisplayEventsbuffer.

6.5 Clear Zone Programming

NO leaves existing zone information intact.

YES setsallzonesinthesystemto*UNUSED*

6.6 Clear Communication

NO - Leavesexistingcommunicationprogrammingintact.

YES - Clears communication to factory defaults.

6.7 Set to Factory Defaults

NO leaves the remainder of the existing communicator programming intact.

YES sets the communicatorprogrammingbacktofactorydefaultselectionsandclears

allZ-WavedeviceprogrammingandFavoritesfromthecommunicator.SelectingYES

does not clear the event memory, zone, user code information, or schedules.

INITIALIZATION

CODES? NO YES

SURE? YES NO

SCHEDS? NO YES

SURE? YES NO

EVENTS? NO YES

SURE? YES NO

ZONES? NO YES

SURE? YES NO

COMMS? NO YES

SURE? YES NO

DEFAULTS? NO YES

SURE? YES NO

CODES?

NO YES

SCHEDS? NO YES

For each section of the panel program you can

initialize, a NO or YES option is provided.

Selecting YES advances you to

a confirmation prompt.

If you select YES, the panel initializes that section of

the program and advances you to the next prompt.

If you select NO, the panel advances you to the next

section prompt but does not initialize that section of

the program.

SURE? YES NO

Selecting NO

advances you to

the next prompt.

InItIalIzatIon

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

Communication

7.1 Communication

TheCommunicationsectionallowsyoutocongurethecommunicationsettingsforthe

iComSL

Communicator.AfterchoosingtheCommunicationType,continuethroughthe

list of options.

7.2 Account Number

Entertheaccountnumbersenttothereceiver.

Therangeofaccountnumbersis1to65535.Foraccountnumbersoffourdigitsorless,

you do not have to enter leading zeros. The

ommunicatorautomaticallyrightjusties

the account number.

7.3 Transmission Delay

Enterthenumberofseconds(15to45seconds)thecommunicator waits before sending

burglaryalarmreportstothereceiver.Enter0(zero)todisablethisfunction.The

defaultis0.

7.4 Communication Type

The

ommunicatorusesNetworkcommunicationtoDMPModelSCS-1RorSCS-VR

Receivers.

7.5 Test Time

PressCOMMANDtodisplaytheTestTime.Enterthetimeofdaythecommunicator sends

thetestreporttotheSCS-1RorSCS-VRReceivers.Useentriesbetween12:00to11:59

andthenchooseAMorPM.

7.6 Test Days

Enterhowoftenthepaneltestreportissenttothereceiver.Enterfrom1to60days.

Enterzerotodisablethetestreport.Defaultis1(one)day.Theseoptionsonlydisplayif

a test time is entered.

7.7 Check-in Minutes

Check-inreportsareamethodofsupervisingthepanelforcommunicationwiththe

receiver.

Enterthenumberofminutesbetweencheck-inreports.Selectfrom0or3-240minutes.

Enter0(zero)todisablethecheck-inoption.Defaultis0.

7.8 Fail Time

FailTimeallowstheSCS-1RorSCS-VRreceivertomissadenednumberofcheck-ins

before logging that the panel is missing. For example, if NET CHECKIN is20andFAIL

TIMEis30,theSCS-1RreceiveronlyindicatesaPanelNotRespondingafter30minutes.

The FAIL TIME must be equal to or greater than the NET CHECKIN minutes: If the

CHECKINis20minutes,theFAIL TIME mustbe20ormore.ThemaximumFAIL TIME is

240minutes.Selectfrom0or3-240minutes.ThedefaultFAIL TIME is240minutes.

7.9 Receiver 1 Programming

Allowsyoutosettheoptionsfortherstreceiverthe

ommunicator attempts to

contact when sending reports. The

communicator

supports communication to two

receivers.

7.10 Alarm Reports

YESenablesAlarm,AlarmRestoral,ExitError,andSystemRecentlyArmedreportstobe

senttothisreceiver.DefaultisYES

7.11 Supervisory/Trouble Reports

YESenablesSupervisory,Trouble,TroubleRestoral,ForceArmed,andFaultreportstobe

senttothisreceiver.DefaultisYES.

7.12 Opening/Closing and User Reports

YESenablesOpening/Closing,ScheduleandCodeChanges,andBypassreportsbyuserto

besenttothisreceiver.DefaultisYES.

7.13 Test Report

EnterYEStoenabletheRecallTestreporttobesenttothisreceiver.

7.14 First IP Address

Entertherst(primary)IPaddresswherethe

ommunicator sends messages. The IP

addressmustbeuniqueandcannotbeduplicatedonthenetwork.Enterall12digitsand

leaveouttheperiods.Forexample,enterIPaddress192.168.0.250as192168000250.

The periods display automatically.

7.15 First IP Port

EntertherstIPportnumbertobeusedinconjunctionwiththeFirstIPAddress.TheIP

portidentiestheportusedtocommunicatemessagestoandfromthecommunicator.

ThedefaultIPPortsettingis2001.

COMMUNICATION

ACCOUNT NO:

XMIT DELAY: 0

COMM TYPE: CELL

CELL TST DAYS: 1

CHECKIN: 0

FAIL TIME: 240

RECEIVER 1 PROG

ALARM NO YES

SPV/TRBL NO YES

O/C USER NO YES

TEST RPT NO YES

FIRST IP ADDR

000.000.000.000

FIRST IP PORT

2001

TEST TIME

00:00 AM

communIcatIon

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guide

communIcatIon

7.16 Second IP Address

EnterthesecondIPaddresswherethecommunicator sendsnetworkmessages.TheIP

Addressmustbeuniqueandcannotbeduplicatedonthenetwork.Enterall12digitsand

leaveouttheperiods.Forexample,enterIPaddress192.168.0.250as192168000250.

The periods display automatically.

7.17 Second IP Port

EnterthesecondIPportnumbertobeusedinconjunctionwiththeSecondIPAddress.

TheIPportidentiestheportusedtocommunicatemessagestoandfromthe

communicator.ThedefaultIPPortsettingis2001.

7.18 Receiver 2 Programming

Allowsyoutosettheoptionsforthesecondreceiverthecommunicator attempts to

contact when sending reports. The communicator supports communication to two

receivers.IfyouselectYESforanyoftheReceiver2options,youmusthaveatleastone

IPaddressprogrammedinReceiver2programming.Receiver2defaultsaresettoNO.

7.19 Alarm Reports

YESenablesAbort,Alarm,AlarmRestoral,AlarmBellSilenced,Ambush,ExitError,and

SystemRecentlyArmedreportstobesenttothisreceiver.DefaultisNO.

7.20 Supervisory/Trouble Reports

YESenablesSupervisory,Trouble,TroubleRestoral,ForceArmed,LatetoClose,and

Faultreportstobesenttothisreceiver.DefaultisNO.

7.21 Opening/Closing and User Reports

YESenablesOpening/Closing,ScheduleandCodeChanges,andBypassreportsbyuserto

besenttothisreceiver.DefaultisNO.

7.22 Test Report

YESenablestheRecallTestreporttobesenttothisreceiver.DefaultisNO.

7.23 First IP Address

Entertherst(primary)IPaddresswherethe

ommunicator sends messages. The IP

addressmustbeuniqueandcannotbeduplicatedonthenetwork.Enterall12digitsand

leaveouttheperiods.Forexample,enterIPaddress192.168.0.250as192168000250.

The periods display automatically.

7.24 First IP Port

EntertherstIPportnumbertobeusedinconjunctionwiththeFirstIPAddress. 

TheIPportidentiestheportusedtocommunicatemessagestoandfromthepanel.

ThedefaultIPPortsettingis2001.

7.25 Second IP Address

EnterthesecondIPaddresswherethecommunicator sendsnetworkmessages.TheIP

Addressmustbeuniqueandcannotbeduplicatedonthenetwork.Enterall12digitsand

leaveouttheperiods.Forexample,enterIPaddress192.168.0.250as192168000250.

The periods display automatically.

7.26 Second IP Port

EnterthesecondIPportnumbertobeusedinconjunctionwiththeSecondIPAddress.

TheIPportidentiestheportusedtocommunicatemessagestoandfromthepanel.

ThedefaultIPPortsettingis2001.

SECOND IP ADDR

000.000.000.000

SECOND IP PORT

2001

RECEIVER 2 PROG

ALARM NO YES

SPV/TRBL NO YES

O/C USER NO YES

TEST RPT NO YES

FIRST IP ADDR

000.000.000.000

FIRST IP PORT

2001

SECOND IP ADDR

000.000.000.000

SECOND IP PORT

2001

iComSL

Series Universal Communicator Installation and Programming Guide Digital Monitoring Products

messagIng setup

Messaging Setup

8.1 Messaging Setup

This section allows you to enter the information needed to send and receive messages

directlytoandfromthepanelviaEmailusingnetworkcommunication.TheDestination

addressesallowupto48characterstobeentered.SystemNameisdisplayedwithinitial

caps.

The transmitted messages are:

•ZoneAlarmsbyZoneName

•ZoneTroublesbyZoneName

•ZoneBypassbyUser

•Arming(Closings)byUser

•Disarming(Openings)byUser

•ACPowerTroubleandRestoral

•SystemLowBattery

•CancelbyUser

8.2 Enable Messaging

SelectYEStoallowthepaneltosendmessagestothreeprogrammeddestinations.

DefaultisNO.

8.3 System Name

Enterauniq

ue name for the communicator. The communicator name is used as the

sender of the message. The text entered is displayed w

ithinitialcaps.Ifthiseldisleft

blank,thecommunicatoraccountnumberissent.

8.4 Destination 1

EntertherstEmailaddresswheremessageswillbesent.Themessagecanbesentto

anydevice(computer,cellphone,tablet)aslongasavalidEmailaddressisentered.

WhenenteringEmailaddresses,pressthe7digitkeyfollowedbythefourthSelectKey

toaddthe@symbolandthe9digitkeyfollowedbythefourthSelectKeytoaddthe_

symbol.SeetheEnteringNon-AlphaCharacterssectionforadditionalsymbols.

8.5 Destination 1 User Number

Enterauser’susernumberfromthisaccount.Thisoptionisusedwhensendingcommands

suchasarmingordisarmingtotheiComSLusingEmail.Theusernumbermusthavethe

authoritytoperformthecommands.Entering0(zero)disablesthisoption.Defaultis0.

8.6 Destination 2

EntertheseconddestinationEmailaddress.

8.7 Destination 2 User Number

Entertheuser’sUserNumberforarming/disarmingauthorization.

8.8 Destination 3

EnterthethirddestinationEmailaddress.

8.9 Destination 3 User Number

Entertheuser’sUserNumberforarming/disarmingauthorization.

8.10 O/C Email

SelectYEStoallowthepaneltosendOpeningandClosingreportsviaEmail.

DefaultisNO.

8.11 Monthly Limit

ThisnumberlimitsthemonthlyincomingandoutgoingEmailmessagesallowedtobe

sent or received by the panel.

ApaneleventthatcausesmessagestobesenttodestinationEmailaddressesiscounted

towardsthepanel’smonthlylimit.Forexample,ifanalarmmessageissenttoanEmail

address,atotalof2messagesarecountedtowardsthemonthlylimitforthepanel.The

limitisresetatmidnightonthe14thofeverymonth.Rangeisfrom0to999.When0is

entered, there is no limit on the number of messages able to be sent or received by the

panel.Defaultis0.

TheremainingoptionsallowtheEmailservertobeselectedbytheinstallingdealer.

TypicallythiswillbetheEmailserviceprovidedbytheinstallingdealer.Thisallows

opportunity for additional services to be provided to the end user.

MESSAGING SETUP

DESTINATION 1

DESTINATION 2

USER NUMBER:

DESTINATION 3

SYSTEM NAME

ENABLE MESSAGING

NO YES

DESTINATION 1

USER NUMBER:

O/C EMAIL NO YES

DESTINATION 3

USER NUMBER:

MONTHLY LIMIT: 0

Digital Monitoring Products

iComSL

Series Universal Communicator Installation and Programming Guide

messagIng setup

8.12 SMTP Server

EntertheSMTP(SimpleMailTransferProtocol)Servername.TheSMTPEmailserveris

responsibleforsendingtheEmailtoitsdestination.AnexampleSMTPEmailservername

is:mail.somedomain.com.ThedomainshouldbetheEmailserverthatwillprovide

Emailsupportforyouralarmcustomers.

8.13 SMTP Server Port

  TheSMTPserverportnumberistheportthatthepanelusestoinitiateaTCPconnection

withtheEmailserver.Thedefaultportis25.

8.14 SMTP Username

  MostSMTPserversrequireausernametosendEmail.ThiswillbesenttotheSMTP

serverinconjunctionwiththeSMTPPasswordtoprovideEmailauthenticationtothe

server.

8.15 SMTP Password

  MostSMTPserversrequireapasswordtosendEmail.ThiswillbesenttotheSMTPserver

inconjunctionwiththeSMTPUsernametoprovideEmailauthenticationtotheserver.

8.16 From Email Address

  EntertheEmailaddressonlewiththeEmailservice.ThiswillshowupintheEmail

messagesasthesender’saddress.

SMTP SERVER

SMTP PORT: 25

SMTP USERNAME

SMTP PASSWORD

FROM EMAIL

Page is loading ...

DMP Electronics CellCom SLC User manual

Brand: DMP Electronics

Model: CellCom SLC

Type: User manual

This manual is also suitable for

Download PDF

report

DMP Electronics CellCom SLC User manual

This manual is also suitable for

DMP Electronics CellCom SLC User manual

Related papers

Other documents