DMP Electronics 1114 Installation guide

Brand: DMP Electronics

Model: 1114

Category: Wall transmitters

Type: Installation guide

DMP Electronics 1114 is a wireless four-zone expander that increases the number of zones on DMP panels for use with sensors and other non-powered devices. Compatible with all DMP 1100 Series Wireless Receivers and Panels, the 1114 offers flexible power options with a 3.0V Lithium battery or optional 12 VDC power supply. Enjoy the convenience of programming the 1114 as a zone in Zone Information, entering the eight-digit serial number for easy setup. Utilize the survey capability to confirm communication with the receiver while the cover is removed, ensuring proper placement and operation.

1114 Wireless Four-Zone Expander

Description

The 1114 Wireless Four-Zone Expander increases the number of reporting zones available on DMP Panels. Use the

four zones with burglary or other non-powered devices. The 1114 is designed to operate on one CR123A battery or

connect to an optional 12 VDC power supply.

Compatibility

All DMP 1100 Series Wireless Receivers and Panels

What is included

The 1114 includes the following:

• One1114WirelessFour-ZoneExpander

• One3.0VLithiumCR123Abattery

• Hardwarepackwith470kEOLResistors

• Serialnumberlabel

Optionalitemsavailable:

• Model376LDCPowerSupply

• Model505-1212VDCPowerSupply

Serial Number

For your convenience, an additional pre-printed serial number label is included. Prior to installing the zone

expander, record the serial number or place the pre-printed serial number label on the panel programming sheet.

This number is required during programming.

Programming the 1114 in the Panel

Program the 1114 Wireless Four-Zone Expander as a zone in Zone Information. At the Serial Number: prompt, enter

the eight-digit serial number. Continue to program the zone as directed in the panel programming guide. Refer to

theXR500SeriesProgrammingGuide(LT-0679),theXR100SeriesProgrammingGuide(LT-0896),theXT30/XT50Series

ProgrammingGuide(LT-0981),theXTLProgrammingGuide(LT-1108),ortheXTLNProgrammingGuide(LT-1221)as

needed.

Note: When a receiver is installed, powered down and powered up, the panel is reset, or programming is complete,

thesupervisiontimeisreset.Ifthereceiverhasbeenpowereddownformorethanonehour,the1114maytake

up to an additional hour to send a supervision message unless tripped, tampered, or powered up. This operation

extendsbatterylife.Amissingmessagemaydisplayonthekeypaduntilthesupervisionmessageissent.

Selecting the Proper Location (LED Survey Operation)

The1114providesasurveycapabilitytoallowonepersontoconrmcommunicationwiththereceiverwhilethe

coverisremoved.The1114PCBRedSurveyLED(SeeFigure2)turnsonwheneverdataissenttothereceiverthen

immediatelyturnsoffwhenthereceiveracknowledgementisreceived.Pressingthetamperswitchisaconvenient

waytosenddatatothereceivertoconrmoperation.Whenthe1114doesnotreceiveanacknowledgementfrom

thereceiverthesurveyLEDremainsonforabout8secondstoletyouknowcommunicationisnotestablished.

CommunicationisalsofaultywhentheLEDashesmultipletimesinquicksuccession.Relocatethe1114or

receiveruntiltheLEDimmediatelyturnsoffindicatingthe1114andreceiverarecommunicatingproperly.Proper

communicationbetweenthe1114andreceiverisveriedwhenforeachpressorreleaseofthetamperswitch,the

LEDblinksimmediatelyonandimmediatelyoff.

Squeeze to

Remove Cover

Squeeze to

Remove Cover

Figure 1: 1114 Wireless Four-Zone Expander

InstallatIon GuIde

Digital Monitoring Products 1114 Installation Guide

Installing the 1114

Mountthe1114onaatsurfacesuchasawallorsingle-gangbox.WhenusingtheoptionalModel376Lplug-inpower

supply, mount the 1114 near a wall outlet. See Figure 2 for mounting hole locations.

Red LED

(Survey)

Ta mper

Switch

Mounting Holes

3.0V

Lithium

Battery

—

Internal

Antenna

Location

- +

DC Power

2-position

Terminal Block

EXT BAT

Figure 2: 1114 Four-Zone Expander PCB

1114 Zone Wiring

It is recommended to locate zone devices within 100 feet of the

1114zoneexpander.Use22or18AWGwiretocompletethe

connections between the 1114 zone expander Zones 1 through

4andeachelddevice.Eachzoneterminateswithoneofthe

included470kEOLresistorsasshown.

Powering the 1114

The 1114 can be powered by:

• CR123A3.0VDCbattery

• Model376Lplug-inpowersupply

• 12VDCPowerSupply

Note: When setting up a wireless system, it is recommended to program zones and connect the receiver before

installing batteries in the 1114 or connecting the optional power supply.

Battery Power

Observepolaritywheninstallingthebattery.Useonly3.0VLithiumbatteries,DMPModelCR123,ortheequivalent

battery from a local retail outlet. Do not connect the power supply when operating using battery power.

1. Squeeze the cover left and right sides together to remove. See Figure 1.

2. Install the supplied jumper on the two J1 pins next to BAT to enable battery operation.

Note: Battery operation is not enabled if the jumper is on the J1 pins next to EXT.

3. If replacing the battery, remove the old battery and dispose of it properly.

4.Placethe3.0VLithiumbatteryintheholderandpressintoplace.SeeFigure2forBatterylocation.

5.Snapthecoverbackintoplace.

Caution:Properlydisposeofusedbatteries.Donotrecharge,disassemble,heatabove212°F(100°C),

 orincinerate.Riskofre,explosion,andburns.

470k EOL

Figure 3: 1114 Zone Terminals

1114 Installation Guide Digital Monitoring Products

Battery Life Expectancy

Typicalbatterylifeexpectancyforthe1114isthreeyears.RefertotheXR500SeriesProgrammingGuide

(LT-0679),XR100SeriesProgrammingGuide(LT-0896),theXT30/XT50SeriesProgrammingGuide(LT-0981),theXTL

ProgrammingGuide(LT-1108),ortheXTLNProgrammingGuide(LT-1221)asneeded.

DMP wireless equipment uses two-way communication to extend battery life.

The following situation can extend battery life expectancy:

• Extendtransmittersupervisiontimeinpanelprogramming.

The following situations can reduce battery life expectancy:

• Ifareceiverisunpluggedornotinstalled.

Note:Transmitterscontinuetosendsupervisionmessagesuntilareceiverreturnsanacknowledgement.

Afteranhourthetransmitteronlyattemptsasupervisionmessageevery60minutes.

• Wheninstalledinextremehotorcoldenvironments.

Optional External DC Plug-in Power Supply

WhenusingtheoptionalModel376Lplug-inDCpowersupply,mountthe

1114 near a wall outlet. Do not install a battery when operating using

the plug-in power supply. The power supply does not charge the battery.

Use the following steps to connect the plug-in power supply:

1. Squeeze the left and right cover sides together to remove. See

Figure 1.

2. Install the supplied jumper on the two J1 pins next to EXT to

enable power supply operation.

Note: Power supply operation is not enabled if the jumper is on the

J1 pins next to BAT.

3.WirethepowersupplytotheJ2terminalblock.ConnecttheBlackwirewiththeWhitestripetothepositive

terminalandtheBlackwiretothenegativeterminal.SeeFigure4.

4.Snapthecoverbackintoplace.

5.PlugtheModel376Lpowersupplyintoa110VoltACoutlet.

Optional External 12 VDC Power Supply

The1114canalsobepoweredfroma12VDCpowersupplysuchasaDMPModel505-12.Use22AWGwiretoconnect

to the power supply. Do not install a battery when operating using the external power supply. The power supply does

not charge the battery.

Use the following steps to connect the power supply:

1. Squeeze the left and right cover sides together to remove. See

Figure 1.

2. Install the supplied jumper on the two J1 pins next to EXT to

enable power supply operation.

Note: Power supply operation is not enabled if the jumper is on

the J1 pins next to BAT.

3.Using22AWGwire,connecttheJ2terminalblocktotheJ6

terminalonthe505-12powersupplyPCB.SeeFigure5.

4.Observepositiveandnegativepolarityonallconnections.

5.Snapthecoverbackintoplace.

Plug-in

Power

Supply

DC Power

2-position

Terminal Block

- +

Black Wire

with White

Stripe

to Positive

Black Wire

to Negative

Figure 4: 1114 Side View

+ DC -

505-12 Power

Supply

12 VDC

22 AWG Wire

DC Power

2-position

Terminal Block

- +

Figure 5: Power Supply Connection

14405

800-641-4282

      

www.dmp.com 2500 North Partnership Boulevard







Specications

Battery

LifeExpectancy 3years

Type 3.0VLithiumCR123A

SeeBatteryLifeExpectancyforfulldetails.

FrequencyRange 903-927MHz

Dimensions 4.65”Lx3.1”Wx1.4”H

Color White

HousingMaterial FlameretardantABS

Accessories

CR123 DMP3.0VLithiumBattery

376L DCPlug-inPowerSupply

505-12 12VDCPowerSupply

Compatibility

1100D Wireless Receiver using version 104

1100DHWirelessHighPowerReceiverusingversion105

1100DIWirelessIn-lineReceiverusingversion105

1100X Wireless Receiver using version 104

1100XHWirelessHighPowerReceiverusingversion105

XTLPanelwithintegratedwirelessreceiverusingversion104

XTLNPanelwithintegratedwirelessreceiver

XT30/XT50Seriespanelwithintegratedwirelessreceiver

using version 101

Patents

U.S.PatentNo.7,239,236

Listings and Approvals

FCCPart15RegistrationIDCCKPC0101

ICRegistrationID5251A-PC0101

FCC Information

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions

(1)Thisdevicemaynotcauseharmfulinterference,and

(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.

Theantennausedforthistransmittermustbeinstalledtoprovideaseparationdistanceofatleast20cm(7.874in.)

from all persons. It must not be located or operated in conjunction with any other antenna or transmitter.

Changesormodicationsmadebytheuserandnotexpresslyapprovedbythepartyresponsibleforcompliancecould

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoes

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

DMP Electronics 1114 Installation guide

Brand: DMP Electronics

Model: 1114

Category: Wall transmitters

Type: Installation guide

Download PDF

report

DMP Electronics 1114 Installation guide

DMP Electronics 1114 Installation guide

Related papers

Other documents