H3C SecPath M9000 NSQ1SUPB0 MPU User manual

Brand: H3C

Model: SecPath M9000 NSQ1SUPB0 MPU

Type: User manual

Manual Version: 6PW102-20170414 BOM: 3123A0R4

H3C SecPath M9000 NSQ1SUPB0 MPU manual

1 Card view

Figure 1 NSQ1SUPB0 MPU

2 Specifications

Figure 2 Front panel of the NSQ1SUPB0

(1) Console port (CONSOLE) (2) 10/100/1000BASE-T copper combo port GE3

(3) Mana

ement Ethernet port LED (4) Fan status LED

(5) Card status LED (6) MPU status LED (ACTIVE)

(7) Reset button

Table 1 Card specifications

Item S

ecification

Dimensions (H × W × D) 40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)

Power consumption 45 W to 50 W

Weight 2.97 kg (6.55 lb)

Hot swapping Supported

Connector type RJ-45

Interfaces

• 1 console port

• One 10/100/1000BASE-T Ethernet port

Ambient temperature

Operating: 0°C to 45°C (32°F to 113°F)

Storage: –40°C to +70°C (–40°F to +158°F)

4 51 2 6 7

Manual Version: 6PW102-20170414 BOM: 3123A0R4

Item S

ecification

Ambient humidity

Operating: 10%RH to 95%RH, noncondensing

Storage: 5%RH to 95%RH, noncondensing

Compatible device model and slot

• M9006 multi-service security gateway (Slot 0 and Slot 1)

• M9010 multi-service security gateway (Slot 4 and Slot 5)

• M9014 multi-service security gateway (Slot 6 and Slot 7)

Table 2 Console port specifications

Item S

ecification

Connector RJ-45

Interface standard RS-232

Transmission baud rate 9600 bps (default) to 115200 bps

Transmission medium Asynchronous serial cable

Transmission distance ≤15 m (49.21 ft)

Services

• Provides connection to an ASCII terminal.

• Provides connection to the serial port of a local or remote (through a

pair of modems) PC running terminal emulation program.

• Supports command line interface (CLI)

Table 3 10/100/1000BASE-T copper port specifications

Item S

ecification

Connector RJ-45

Interface standard 802.3, 802.3u, and 802.3ab

Interface type MDI/MDIX autosensing

Supported cable Category-5 (or above) twisted pair cable

Transmission distance 100 m (328.08 ft)

Port transmission rate

• 10 Mbps, half/full duplex

• 100 Mbps, half/full duplex

• 1000 Mbps, full duplex

3 LEDs

Table 4 Ethernet port LED description

LIN

ACT Descri

tion

On Flashing

A link is present, and the management Ethernet port is receiving or

sending data.

On Off A link is present.

Off Off No link is present.

Manual Version: 6PW102-20170414 BOM: 3123A0R4

iii

Table 5 Ethernet port LED description

FAIL Descri

tion

On Off The fan tray is operating correctly.

Off On A fan problem is present or the fan tray is not in position.

Off Off The gateway is not powered on.

Table 6 MPU RUN and ALM LED description

RUN ALM Descri

tion

Flashing Off The card is operating correctly.

Flashing On

The card is loading software.

If the LED flashes continuously, the software version of the device does

not match that of the card.

On On The card is booting or faulty.

On Off The MPU is starting up.

Off Off The card is not in position.

NOTE:

• A quick flashing RUN LED indicates that the card is starting up rather than operating properly.

• It is normal that the ALM LED for an LPU li

hts for a period of time at the initial phase of the system

startup.

Table 7 MPU ACTIVE LED description

LED status Descri

tion

On The MPU is active.

Off

• The MPU is in standby status.

• The MPU is faulty. Examine the card LED for an MPU problem.

4 Installing and removing the NSQ1SUPB0 MPU

CAUTION:

• Wear a well-grounded ESD-preventive wrist before you install or remove the card.

• Do not touch the surface-mounted components directly with your hands when you install or remove

the card.

4.1

Installing the NSQ1SUPB0

1. Face the front panel of the device.

2. Identify the slot to install the card, and remove the filler panel from the slot.

This manual uses slot 1 as an example.

Manual Version: 6PW102-20170414 BOM: 3123A0R4

Place the card horizontally with the surface-mounted components facing upward. Pull outward the

ejector levers and gently push the card in along the slot guide rails until the card is in close contact

with the backplane. (See callout 1 in Figure 3 .)

4. Push the ejector levers inward. (See callout 2 in Figure 3 .)

5. Tighten the captive screws with a Phillips screwdriver to secure the card in the slot. (See callout 3

in Figure 3 .)

Figure 3 Installing the

NSQ1SUPB0

(1) Gently push the card in along the slot guide rails until the card is in close contact with the backplane.

(2) Push the ejector levers inward.

(3) Ti

hten the captive screws with a Phillips screwdriver, and installation is finished.

4.2

Removing the NSQ1SUPB0

1. Use a Phillips screwdriver to loosen the captive screws at both sides of the card until all pressure

is released.

2. Pull the ejector levers at both sides of the card outward, and pull the card along the guide rails until

it completely comes out of the backplane.

3. Place the card on an anti-static workbench with the surface-mounted components up, or put it in an

anti-static bag.

If no new card is to be installed, install a filler panel to prevent dust and ensure good ventilation in

the device.

5 Software upgrade

For more information, see the release notes.

6 Obtaining documentation

To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:

1. Go to http://www.h3c.com.hk/Technical_Documents.

2. Choose the desired product category and model.

H3C SecPath M9000 NSQ1SUPB0 MPU User manual

H3C SecPath M9000 NSQ1SUPB0 MPU User manual

H3C SecPath M9000 NSQ1SUPB0 MPU User manual

Related papers

Other documents