H3C SecPath M9000-S NSQM2MPUD0 User manual
- Type
- User manual
Manual version: APW100-20171225 BOM: 3123A1Q1
i
H3C SecPath M9000-S NSQM2MPUD0 main
processing unit
1 Identifier
The module identifier NSQM2MPUD0 is at the upper right corner of the front panel.
2 Specifications
The NSQM2MPUD0 MPU has a console port, a USB port, a Mini USB console port, two
10/100/1000Base-T copper ports, and two GE SFP fiber ports.
Figure 1 Front panel
(1) 10/100/1000Base-T copper port LEDs (LINK and ACT) (2) SFP port LEDs (LINK and ACT)
(3) Power module status LED (PWR) (4) Module status LEDs
(5) Active/standby state LED (ACTIVE) (6) Reset button (RESET)
(7) Fan tray status LED (FAN) (8) GE SFP fiber port
(9) 10/100/1000Base-T copper port (10) Console port (CONSOLE)
(11) USB console port (12) USB port
(13) Ejector lever (14) Captive screw
Table 1 Module specifications
Item Specifications
Flash 1 GB
SDRAM (DDR3) 4 GB
Dimensions (H × W × D) 45 × 399 × 355 mm (1.77 × 15.71 × 13.98 in)
Power consumption 45 to 86 W
Weight 4 kg (8.82 lb)
Hot swapping Supported
Port
• 1 × console port
• 1 × USB console port
• 1 × USB 2.0 port
• 4 × network management ports, including two 10/100/1000Base-T
ports and two SFP ports
Manual version: APW100-20171225 BOM: 3123A1Q1
ii
Item Specifications
Ambient temperature
• Operating: 0°C to 45°C (32°F to 113°F)
• Non-operating: –40°C to +70°C (–40°F to +158°F)
Ambient humidity
• Operating: 10 to 95% RH, noncondensing
• Non-operating: 5% RH to 95% RH, noncondensing
Compatible device models and
slots
M9008-S gateway (slots 0 and 1)
IMPORTANT:
• To verify compatibility of the MPU with the software release you are using, see the release notes.
• To connect an SFP fiber management Ethernet port on the MPU, make sure the peer port
operates at 1000 Mbps in full-duplex mode.
• The USB port on the MPU does not support USB extension cables.
Table 2 Console port specifications
Item Specifications
Connector type RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
Services
• Provides connection to an ASCII terminal.
• Provides connection to the serial port of a local PC running
terminal emulation program.
• Supports command line interface (CLI)
Table 3 10/100/1000BASE-T Ethernet copper port specifications
Item Specifications
Connector type RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Transmission medium Category-5 (or above) twisted pair cable
Transmission distance 100 m (328.08 ft)
Transmission rate and working
mode
• 10 Mbps, half/full duplex
• 100 Mbps, half/full duplex
• 1000 Mbps, full duplex
Table 4 1000BASE-X SFP fiber port specifications
Item Specifications
Connector type LC
Transmission medium and
maximum transmission distance
SFP transceiver modules: see Table 5.
Manual version: APW100-20171225 BOM: 3123A1Q1
iii
Item Specifications
Interface standard 802.3, 802.3u, and 802.3ab
Transmission rate and working
mode
1000 Mbps, full duplex
Table 5 SFP modules available for the 1000BASE-X SFP fiber ports
Module
Central
wavelength
Connector
type
Cable
specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-A 850 nm LC
50/125 µm
multi-mode optical
fiber (MMF)
550 m (0.34 miles)
62.5/125 µm MMF 275 m (0.17 miles)
SFP-GE-SX-MM850-D 850 nm LC
50/125 µm MMF 550 m (0.34 miles)
62.5/125 µm MMF 275 m (0.17 miles)
SFP-GE-LX-SM1310-A 1310 nm LC
9/125 µm
single-mode
optical fiber (SMF)
10 km (6.21 miles)
50/125 µm MMF 550 m (1804.46 ft)
62.5/125 µm MMF 550 m (1804.46 ft)
SFP-GE-LX-SM1310-D 1310 nm LC
9/125 µm SMF 10 km (6.21 miles)
50/125 µm MMF 550 m (1804.46 ft)
62.5/125 µm MMF 550 m (1804.46 ft)
SFP-GE-LH40-SM1310 1310 nm LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH40-SM1310-D 1310 nm LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH40-SM1550 1550 nm LC 9/125 µm SMF
40 km (24.86 miles)
SFP-GE-LH80-SM1550 1550 nm LC 9/125 µm SMF 80 km (49.71 miles)
SFP-GE-LH80-SM1550-D 1550 nm LC 9/125 µm SMF 80 km (49.71 miles)
SFP-GE-LH100-SM1550 1550 nm LC 9/125 µm SMF
100 km (62.14 miles)
SFP-GE-LX-SM1310-BIDI
RX: 1490 nm
TX: 1310 nm
LC 9/125 µm SMF
10 km (6.21 miles)
SFP-GE-LX-SM1490-BIDI
RX: 1310 nm
TX: 1490 nm
LC 9/125 µm SMF
10 km (6.21 miles)
NOTE:
• BIDI modules use different central wavelengths in transmit and receive directions to implement
bidirectional transmission of optical signals over the same fiber.
• BIDI modules must be used in pairs. For example, if an SFP-GE-LX-SM1310-BIDI is used at one
end, you must use an SFP-GE-LX-SM1490-BIDI at the other end.
Manual version: APW100-20171225 BOM: 3123A1Q1
iv
3 LEDs
Table 6 LED description
LED Status Description
10/100/1000Base-T
/SFP port LED
(LINK and ACT)
• LINK LED: On
• ACT LED: Flashing
A link is present on the port and the port is sending or
receiving data.
• LINK LED: On
• ACT LED: Off
A link is present on the port.
• LINK LED: Off
• ACT LED: Off
No link is present on the port.
Power module
status LED (PWR)
Green All the power modules in position are operating correctly.
Red
A power module is not outputting power. The reason
might be power module failure, power switch turned off,
power cord connection fault, or mains power failure.
Off
• No power modules are installed in the chassis.
• No power modules in position are outputting power.
The reason might be power modules failure, power
switches turned off, power cords connection fault,
or mains power failure.
Fan tray status LED
(FAN)
Green
• The fan tray is operating correctly.
Red
• The fan tray is faulty or is not in position.
Off
• The device is not powered up.
Module status LED
Flashing green
• The module is operating correctly.
Fast flashing green (4 Hz)
• The module is uploading software. If the LED
remains in this state, the module software does not
match the device software.
Steady red
• The module is starting up or is faulty.
Flashing red
• The module temperature is higher than the upper
warning threshold or lower than the lower warning
threshold.
Off
• The module is not in position.
Active/standby
state LED
(ACTIVE)
On
• The MPU is operating in active state.
Off
• The MPU is operating in standby state.
• The MPU is faulty. To determine whether the MPU
is faulty, observe also the module status LEDs.
4 Installing and removing the MPU
CAUTION:
• Wear a reliably-grounded ESD wrist strap or ESD gloves when you install or remove the MPU.
• Do not touch the components on the PCB.
Manual version: APW100-20171225 BOM: 3123A1Q1
v
4.1
Installing the MPU
1. Face the front panel of the device. Remove the filler panel from the target slot.
This example uses slot 0 on the device.
2. Place the MPU horizontally on a workbench with the PCB facing up. Pull outward the ejector
levers on the MPU.
3. Gently push the MPU into the slot along the guide rails.
4. Push the ejector levers inward until the MPU is in close contact with the backplane.
5. Use a Phillips screwdriver to tighten the captive screws on the MPU.
Figure 2 Installing the MPU
4.2
Removing the MPU
1. Use a Phillips screwdriver to loosen the captive screws on the MPU until all pressure is
released.
2. Simultaneously pull the ejector levers at both sides of the MPU outward to separate the MPU
from the backplane, and pull the MPU slowly out of the chassis along the guide rails.
3. Place the MPU on an anti-static workbench with the PCB facing up, or put it in an anti-static
bag.
4. If you are not to install a new MPU, install a filler panel in the slot to prevent dust and ensure
good ventilation in the device.
5 Software upgrade
For information about upgrading the MPU, see the release notes.
6 Obtaining documentation
To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:
1. Go to http://www.h3c.com.hk/Technical_Documents
.
2. Choose the desired product category and model.
Copyright © 2017 New H3C Technologies Co., Ltd.
-
1
-
2
-
3
-
4
-
5
H3C SecPath M9000-S NSQM2MPUD0 User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
H3C LSQM1EPSB0 User manual
-
-
H3C SecPath F5030-D Installation guide
-
-
-
-
-
-
-
