H3C LSVM1S9810FAN &
LSVM2S9810FAN
Fan Modules User Manual
New H3C Technologies Co., Ltd.
http://www.h3c.com.hk
Document version: 6PW102-20170515
Copyright © 2014-2017, New H3C Technologies Co., Ltd. and
its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or
by any means without prior written consent of New H3C Technologies
Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, ,
H3Care, , IRF, NetPilot, Netflow, SecEngine, SecPath,
SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks
of New H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any
kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental
protection requirements. The storage, use, and disposal of this product
must meet the applicable national laws and regulations.
Obtaining documentation
To access the most up-to-date H3C product documentation, go to the
H3C website at http://www.h3c.com.hk
.
To obtain information about installation, configuration, and maintenance,
click http://www.h3c.com.hk/Technical_Documents
To obtain software version information such as release notes,
click http://www.h3c.com.hk/Software_Download
Technical support
service@h3c.com
http://www.h3c.com.hk
Documentation feedback
You can email your comments about product documentation to
We appreciate your comments.
i
Contents
Fan tray overview ···················································································· 1
LSVM1S9810FAN ············································································· 1
Introduction ···················································································· 1
LED ································································································· 2
Specifications ················································································ 2
LSVM2S9810FAN ············································································· 3
Introduction ···················································································· 3
LED ································································································· 4
Specifications ················································································ 4
Installing and replacing a fan tray ························································· 5
Installing a fan tray ············································································ 5
Replacing a fan tray ·········································································· 9
1
Fan tray overview
LSVM1S9810FAN
Introduction
The LSVM1S9810FAN fan tray contains six fans. It draws cooling air
into the device and provides airflow from the power module side to the
port side. It is hot swappable and energy efficient. It can automatically
adjust the fan speed based on the device temperature.
Figure 1 LSVM1S9810FAN
(1) Captive screw
(2) Handle (The handle is in blue, indicating that the fan tray draws
cooling air into the device.)
2
(3) Airflow sign (4) This side up sign
LED
The LED that shows the fan tray operating status is located on the panel
of the switching fabric module. When the device is running, the LED can
have the following states:
• Green—The fan tray is operating correctly.
• Red—No fan tray is installed or the fan tray is faulty.
Specifications
Table 1 LSVM1S9810FAN specifications
Item Specification
Number of fans
Six 60 × 60 × 38 mm (2.36 × 2.36 × 1.50
in) fans
Airflow direction
From the device power module side to the
port side
Max fan speed 16500 revolutions per minute (R.P.M.)
Max air volume 252 cubic foot per minute (CFM)
Max power
consumption
180 W
Min power
consumption
21 W
Voltage –48 V to –60 V
3
LSVM2S9810FAN
Introduction
The LSVM2S9810FAN fan tray contains six fans. It exhausts warm air
out of the device and provides airflow from the port side to the power
module side. It is hot swappable and energy efficient. It can
automatically adjust the fan speed based on the device temperature.
Figure 2 LSVM2S9810FAN
(1) Captive screw
(2) Handle (The handle is in red, indicating that the fan tray
exhausts warm air out of the device.)
(3) This side up sign (4) Airflow sign
4
LED
The LED that shows the fan tray operating status is located on the panel
of the switching fabric module. When the device is running, the LED can
have the following states:
• Green—The fan tray is operating correctly.
• Red—No fan tray is installed or the fan tray is faulty.
Specifications
Table 2 LSVM2S9810FAN specifications
Item Specification
Number of fans
Six 60 × 60 × 38 mm (2.36 × 2.36 × 1.50
in) fans
Air flow direction
From the device port side to the power
module side
Max fan speed 16500 revolutions per minute (R.P.M.)
Max air volume 252 cubic foot per minute (CFM)
Max power
consumption
180 W
Min power
consumption
21 W
Voltage –48 V to –60 V
5
Installing and replacing a fan tray
The installation and removal procedures are the same for the
LSVM1S9810FAN and LSVM2S9810FAN fan trays.
Installing a fan tray
IMPORTANT:
Before you install a fan tray,
• Determine the required number of fan trays based on the
number of installed switching fabric modules. If one switching
fabric module is installed, one fan tray is required. If two
switching fabric modules are installed, two fan trays are
required.
• Make sure the airflow direction of the fan tray meets the
ventilation requirement at the installation site.
• Make sure a switching fabric module has been installed in the
slot below the target fan tray slot.
• To install two fan trays, make sure the models of the two fan
trays are the same.
To install a fan tray:
1. Wear an ESD wrist strap, and make sure it makes good skin
contact and is reliably grounded.
2. Use both hands to hold the fan tray with the "TOP" sign on the top
surface. Gently push the fan tray into the slot along the guide rails
until the fan tray is completely seated in the slot. See callout 1
in Figure 3 and Figure 4.
6
The fan tray slot is foolproof. If you insert the fan tray with the
upside down, you cannot completely insert it into the slot. If this
happens, pull the fan tray out and then insert it again with the
upside up.
3. Use a Phillips screwdriver to fasten the captive screws on the fan
tray to secure the fan tray in the slot. See callout 2 in Figure 3
and Figure 4.
If the
captive screws cannot be tightened, identify whether the fan
tray is installed correctly.
Figure 3 Installing one fan tray
IMPORTANT:
W
hen one fan tray is required, install it in the lower fan tray slot. To
maintain good ventilation, the upper fan tray slot must have a filler
panel installed.
1
2
7
Figure 4 Installing two fan trays
8
If the target slot has a filler panel installed, remove the filler panel as
follows:
1. Use a Phillips screwdriver to loosen the screws on the filler panel.
2. Insert a flat-blade screwdriver obliquely in the groove on the filler
panel. Then pull the filler panel slowly out along the guide rails.
Figure 5 Removing a filler panel
9
Replacing a fan tray
CAUTION:
• When you replace a fan tray from a running device, be cautious
of electricity hazards, and do not touch the rotating fans to avoid
bodily injury.
• When two fan trays are installed, follow these guidelines to
replace the fan trays:
{ If one fan tray fails, the switch can operate correctly if you
keep the failed fan tray in position, and immediate
replacement is not required. If you want to replace the
failed fan tray, finish the replacement within 3 minutes.
{ If both fan trays fail, replace the fan trays one after
another. Make sure the device does not operate for more
than 2 minutes when no fan trays are installed.
• Make sure the new fan tray is the same model as the replaced
one.
To replace a fan tray:
1. Prepare an antistatic bag for the removed fan tray.
2. Wear an ESD wrist strap, and make sure it makes good skin
contact and is correctly grounded.
3. Use a screwdriver to loosen the captive screws on the fan tray. See
callout 1 in Figure 6.
4. Holding th
e handle of the fan tray, pull the fan tray out of the
chassis. See callout 2 in Figure 6.
5. Put the removed
fan tray into the antistatic bag.
/