H3C LSVM152SCFAN &
LSVM252SCFAN
Fan Modules User Manual
New H3C Technologies Co., Ltd.
http://www.h3c.com.hk
Document version: 6PW102-20170515
Copyright © 2010-2017, New H3C Technologies Co., Ltd. and
its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or
by any means without prior written consent of New H3C Technologies
Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care,
, IRF, NetPilot, Netflow, SecEngine, SecPath, SecCenter,
SecBlade, Comware, ITCMM and HUASAN are trademarks of New
H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any
kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental
protection requirements. The storage, use, and disposal of this product
must meet the applicable national laws and regulations.
Obtaining documentation
To access the most up-to-date H3C product documentation, go to the
H3C website at http://www.h3c.com.hk
.
To obtain information about installation, configuration, and maintenance,
click http://www.h3c.com.hk/Technical_Documents
To obtain software version information such as release notes,
click http://www.h3c.com.hk/Software_Download
Technical support
service@h3c.com
http://www.h3c.com.hk
Documentation feedback
You can email your comments about product documentation to
We appreciate your comments.
i
Contents
Fan tray overview ···················································································· 1
LSVM152SCFAN ··············································································· 1
Introduction to LSVM152SCFAN ················································ 1
LSVM152SCFAN specifications ·················································· 3
LSVM252SCFAN ··············································································· 3
Introduction to LSVM252SCFAN ················································ 3
LSVM252SCFAN specifications ·················································· 5
Installing and replacing a fan tray ························································· 6
Installing a fan tray ············································································ 6
Replacing a fan tray ·········································································· 8
1
Fan tray overview
LSVM152SCFAN
Introduction to LSVM152SCFAN
The LSVM152SCFAN is a fan tray with blowing fans that blow air to the
inside of the device. It comprises four separate fans. The LSVM152SCFAN
features small size, fast heat dissipation, and hot swapping, and can
automatically adjust the fan speed based on the device temperature.
Figure 1 shows the structure and air flow of the fan tray.
T
he fan tray provides a status LED to indicate the operating status of the
module. When the switch is running, the LED can have the following
statuses:
• The LED displays green—The fan tray is operating properly.
• The LED displays red—The fan tray is faulty.
• The LED is off—The fan tray is not correctly installed or is faulty.
2
Figure 1 LSVM152SCFAN structure
1: Captive screw 2: Status LED
3: Handle 4: Air flow sign
5: Air flow
3
LSVM152SCFAN specifications
Table 1 LSVM152SCFAN specifications
Model Item Specification
LSVM
152S
CFAN
Number of fans
40 × 40 × 28 mm (1.57 × 1.57 ×
1.10 in), four fans
Air flow direction
Front-to-back (blows air to the
inside of the device)
Max rotation speed
9500 rpm (revolutions per minute)
Max air volume 40 CFM (cubic foot per minute)
Max power
consumption
8.42 W
Min power
consumption
0.87 W
LSVM252SCFAN
Introduction to LSVM252SCFAN
The LSVM252SCFAN is a fan tray with drawing fans that draw air from
the inside of the device. It comprises four separate fans. The
LSVM252SCFAN features small size, fast heat dissipation, and hot
swapping, and can automatically adjust the fan speed based on the
device temperature. Figure 2 s
hows the structure and air flow of the fan
tray.
4
The fan tray provides a status LED to indicate the operating status of the
module. When the switch is running, the LED can have the following
statuses:
• The LED displays green—The fan tray is operating properly.
• The LED displays red—The fan tray is faulty.
• The LED is off—The fan tray is not correctly installed or is faulty.
Figure 2 LSVM252SCFAN structure
1
2
3
4
5
1: Captive screw 2: Status LED
3: Handle 4: Air flow sign
5: Air flow
5
LSVM252SCFAN specifications
Table 2 LSVM152SCFAN specifications
Model Item Specification
LSVM25
2SCFAN
Number of fans
40 × 40 × 28 mm (1.57 ×
1.57 × 1.10 in), four fans
Air flow direction
Back-to-front (draws air from
the inside of the device)
Max rotation speed 9500 rpm
Max air volume 40 CFM
Max power
consumption
8.42 W
Min power
consumption
0.87 W
6
Installing and replacing a fan tray
You can install and replace the LSVM152SCFAN and LSVM252SCFAN
in the same way. For more information, see “Installing a fan tray“ and
“Replacing a fan tray.”
Installing a fan tray
IMPORTANT:
Before you install a fan tray, make sure that the air flow direction of
the module meets the ventilation requirement at the installation site.
To install a fan tray:
1. Wear an ESD-preventive wrist strap, and make sure that it makes
good skin contact and is properly grounded.
2. Use a screwdriver to loosen the captive screws on the blank filler
panel of the fan tray slot, and then remove the blank filler panel.
See callout 1 in Figure 3.
3. Unpack the
fan tray.
4. Holding the fan tray with both hands with the upside (marked with
an air flow sign) on top, gently push the fan tray into the slot along
the guide rails until the fan tray completely seats into the slot. See
callout 2 in Figure 3.
5. Use a Phillips
screwdriver to fix the captive screws on the fan tray
to secure it into the switch chassis.
6. When the switch is running, check the status LED of the fan tray. If
the LED displays green, the installation is correct.
7
Figure 3 Install a fan tray
1: Remove the blank filler panel
2: Install a fan tray
8
NOTE:
• If you insert the fan tray with the upside facing downward, you
cannot completely insert the module into the slot. If this happens,
pull the fan tray out and then insert it again with the upside on
top.
• If you cannot fix the captive screws, check whether the fan tray is
correctly installed.
Replacing a fan tray
CAUTION:
• When you replace a fan tray from a running switch, be cautious
of electricity hazards, and do not touch the rotating fan to avoid
bodily injury.
• After you unplug a fan tray from a running switch, install a new
fan tray within eight minutes to ensure proper ventilation and heat
dissipation of the switch.
When the fan tray is faulty, you must replace it.
To replace a fan tray:
1. Prepare an antistatic bag for the removed fan tray.
2. Wear an ESD-preventive wrist strap, and make sure that it makes
good skin contact and is properly grounded.
3. Use a screwdriver to loosen the captive screws of the fan tray. See
callout 1 in Figure 4.
4. Holding th
e handle of the fan tray, pull the module out of the
chassis. See callout 2 in Figure 4.
9
5. Put the removed fan tray into the antistatic bag.
6. Install a new fan tray. For more information, see “Installing a fan
tray.”
Figure 4 Remove a
fan tray
1: Loosen the captive screws of
the fan tray
2: Pull the fan tray out of the
chassis
NOTE:
If you replace a fan tray from a running switch, and the airflow
direction of the new fan tray is different from the former one, the
alarm message System fan airflow direction is not preferred on
slot X, please check it. appears. To eliminate the alarm, replace
another fan tray with the same airflow direction, or use the fan
prefer-direction slot
slot-number
{ power-to-port | port-to-power }
command in system view to change the preferred airflow direction
of the switch.
/