Midmark European Assistant's Unit Installation guide

English - 1

midmark.com

003-2310-99 Rev. D (5/3/13)

European Assistant’s Unit: Elevance™ / Procenter

Console Mounted Installation

Language of origin: English

Console

Cover

LH

Mount

Stop

Pin*

Bottom

Screw

Magnet

Leveling

Set

Screw

Mounting

Screw

RH

Mount

*Note:

The stop pin is factory set for a LEFT side mounted console

(patient’s left). Only move the stop pin if you are installing a

RIGHT side mounted console.

Console

Faceplate

Fit lip under

console frame

and secure with

screw on bottom.

Fit lip under console

top, then push ball

studs into ttings in

frame.

Elevance Console

Procenter Console

Console

Cover

Console Side

Cover

Console

Side

Cover

Ball

Stud

Step 1: Install assistant’s unit on console.

A) Raise chair to a comfortable working height.

B) Disconnect power from chair.

C) Remove console side cover (magnetic on Elevance).

D) Loosen bottom screw and remove inside console cover.

Procenter console only: loosen two screws and slide off faceplate.

E) Install three leveling set screws.

F) Install three mounting screws.

G) Position mounting arm straight out from console.

H) Rotate ADAPTER clockwise before loosely installing mounting screws.

Do Not Tighten mounting screws.

WARNING

Always disconnect power before removing covers. Failure to do so may result in personal injury.

Style G

English - 2

midmark.com

Assistant’s

Umbilical

Step 2: Route the assistant’s umbilical into the console.

Note: Take care not to kink the umbilical.

Vacuum

Line

Leveling

Screw

Mounting

Screw

Elevance ConsoleProcenter Console

Step 3: Level the console mount arm.

A) Adjust the three leveling screws until arm is level.

B) Tighten the mounting screws.

Style G

English - 3

midmark.com

Tubing connections

Water (blue)

Yellow (air)

Curing Light (red

and black wires)

Optional

Vacuum

Power

Console

Cover

Vacuum

Tubing

LIN Line

LIN Coupler

Console

Cover

Caution

Connect gound wire to ensure system ground continuity

Failure to do so may result in electric shock.

Step 4: Make electrical connections inside console.

A) Position electrical connections where the console cover can be installed

over them and screw ground wire to console frame.

B) Adhere LIN coupler inside console with velcro strips. Connect LIN lines

from chair and assistant’s unit.

C) Connect vacuum power to relay harness in the chair umbilical.

Elevance Console

Procenter Console

Ground Wire

Style G

Color Page

English - 4

midmark.com

Note

Tubing and connectors are provided for connecting a

delivery unit and an assistant’s unit. Leave connectors

capped if you are not installing these components.

An additional 1/8" piece of blue tubing is provided that can

be used to connect to a city water supply.

Step 5: Connect like colored tubing for all installed components.

Standard Water Bottle System

OPTIONAL Water Selector Switch System

DA138100i

Elevance Console

Procenter Console

For Procenter Only

Step 5a: Cut 1/8” yellow tubing. Insert T-Fitting. Connect to

1/8” yellow tubing from European Assistant’s Unit.

For Procenter Only

Step 5b: Connect European Assistant’s Unit vacuum

tubing to 3/4” ribbed gray vacuum line from

umbilical.

In J-Box (not shown): Connect 3/4” ribbed

gray vacuum line from umbilical to facility’s

central vacuum line.

For Procenter Only

Step 5c: Remove plugged section of blue tubing.

Connect to 1/8” blue tubing from

European Assistant’s Unit

Style G

Color Page

English - 5

midmark.com

4

0

60

8

0

1

0

20

0

1

2

3

5

6

7

4

0

Step 6: Make connections in J-Box.

A) Remove J-box lid. Connect relay harness to the vacuum power relay box (located in the

installation hardware kit).

B) Have an electrician connect facility power to the vacuum relay box and place relay box inside

the J-box.

C) Connect tubing to facility air and water supplies as shown.

Relay Box

Equipment Alert

Reference product specifications in

the European Assistant’s Unit User

Guide for electrical requirements for

the vacuum.

Facility Power

for Vacuum

Step 7: If no other components are to be installed, finish installation by installing covers.

A) Install J-box lid to cover all tubing and wiring connections.

B) Install console side covers. (Refer to Step 1.)

Note: Be careful not to pinch or kink tubing or wires when installing covers.

Relay Harness

Style G

Color Page

English - 6

midmark.com

Installation Checklist

Test Verify the following:



1

Mounting arm and assistant’s unit are level, rotate

and move easily.

2

Air and water work at syringe. Flow control knobs

adjust flow as expected.

3

Vacuum instruments work as expected.

Solids collector basket is in place.

4

Wipe console and assistant’s unit with a soft dry

cloth to remove dirt or smudges.

5 Curing light (optional) works.

Step 8: Connect chair to power supply.

A) Connect power supply to facility power.

B) Verify operation of the European assistant’s unit.

Air Water

Flow Control

Knobs

Solids Collector

HVE

Saliva

Ejector

Vacuum

Optional Curing

Light

Syringe

HVE

Style G

Page is loading ...

Midmark European Assistant's Unit Installation guide

Midmark European Assistant's Unit Installation guide

in other languages

Related papers

Other documents