Midmark Elevance® Standard Delivery System Installation guide

1

TP201 Rev. A

LR mounted units

Step 2: Remove seat upholstery and seat frame.

A) Rotate lock knob and lift seat upholstery up to remove.

B) Remove screws/washers and seat shrouds on both sides.

C) Remove two shoulder bolts/washers and lift off seat frame.

Elevance Delivery Retrot Kit

[002-1678-00 for 115 VAC] [002-1678-01 for 230 VAC]

003-2626-00 Rev. A (3/13)

Kit Contents:

USB Power Cable........... 1

USB Ext. Cable (A/B) ..... 1

Elevance Chair PCB Kit.. 1

Language of origin: English

Attention

This kit is designed for replacing a Procenter Delivery Unit (LR or Console mounted) on an

Elevance Chair with an Elevance Delivery Unit.

Covers

Seat Upholstery

Lock Knob

Seat Shroud

Seat Frame

Shoulder

Bolt

Caution - Equipment Alert

Always disconnect chair from the power source before removing

any covers. Failure to do so may result in personal injury.

Step 1: Position chair and disconnect power.

A) Tap a chair cover three times to raise the chair. (Chair beeps until it

reaches the set position).

B) Disconnect the power supply (in J-box).

Console mounted units - go to page 3.

midmark.com

Style G

2

TP201 Rev. A

LR mounted units

Step 3: Disconnect Procenter LR Mounted tubing and wiring.

A) Remove the PC Board cover.

B) Disconnect everything from the interface PC Board and remove*.

C) Disconnect all tubing.

D) Push delivery umbilical and tubing bundle thru hole in chair frame as you

pull them thru and free from the mounting arm.

E) Remove bolt, cap, bearings and entire Procenter delivery from the chair

LR mounting arm.

F) Install Elevance delivery unit - go to page 4.

* Note: Leave jumper attached to Interface PC Board. It is not required for Elevance Unit.

PC Board

Cover

Procenter

Umbilical

Interface

PC Board

with Jumper

Bolt

Cap

Bearings

Mounting

Arm

Remove Procenter LR Mounted Unit

midmark.com

Style G

3

TP201 Rev. A

Remove Procenter Console Mounted Unit

Console mounted units

Step 2: Remove Procenter Console and Delivery Unit.

A) Remove covers from console (both sides).

B) Loosen set screws with Allen wrench (both sides) holding flex arm in console.

C) Lift Procenter Unit and flex arm assembly out of the console.

D) Disconnect all tubing and wiring connections inside of the console*.

E) Loosen leveling bolts and lift console off the mounting arm, freeing the wiring

and tubing harnesses from the console.

F) Install Elevance delivery unit - go to page 4.

* Note: Leave Interface PC Board and jumper in the console. It is not required for Elevance Unit.

Procenter

Delivery Unit

Flex Arm

Loosen set

screws (2)

Outside

Cover

Inside

Cover

Leveling

Bolts (8)

Procenter

Console

midmark.com

Style G

4

TP201 Rev. A

DA3894i

Install the Elevance delivery unit.

A) Reference the LR or Console Elevance installation guide packaged

with the delivery unit.

B) Also, route the USB extension cable and USB power cable from

this kit thru the chair and into the J-Box*.

*Note: Route the USB extension cable with the Type B connector in the chair frame

(or console) and the Type A connector in the J-box.

USB

(Type B)

USB

Power

USB

(Type A)

USB

Power

Chair Umbilical

LR Mounted Units

Console Mounted

Units

To complete installation...

A) Reference Elevance Chair PCB Kit and follow instructions to

replace the chair PCB Board.

B) Install all covers that were removed.

C) Connect chair to power supply.

Elevance

Console

midmark.com

Style G

Midmark Elevance® Standard Delivery System Installation guide

Midmark Elevance® Standard Delivery System Installation guide

Related papers

Other documents