Danfoss SpeedUp Eco Wall Heating - Wet plaster User guide

Danfoss
Brand
Danfoss
Model
SpeedUp Eco Wall Heating - Wet plaster
Type
User guide

Danfoss SpeedUp Eco Wall Heating - Wet plaster

The Danfoss SpeedUp Eco Wall Heating - Wet plaster is a system for heating your home using hot water pipes embedded in the walls. It is a cost-effective and energy-efficient way to heat your home, and it can be used in both new and existing buildings. The system consists of a series of panels that are attached to the walls. The panels are made of a lightweight, durable material that is resistant to heat and moisture. The pipes are then embedded in the panels, and a layer of plaster is applied over the pipes. The SpeedUp Eco Wall Heating system can be used with any type of flooring, and it can be installed under carpets, tiles, or hardwood floors. It is also compatible with most types of wall coverings, including paint, wallpaper, and fabric.

Danfoss SpeedUp Eco Wall Heating - Wet plaster

The Danfoss SpeedUp Eco Wall Heating - Wet plaster is a system for heating your home using hot water pipes embedded in the walls. It is a cost-effective and energy-efficient way to heat your home, and it can be used in both new and existing buildings. The system consists of a series of panels that are attached to the walls. The panels are made of a lightweight, durable material that is resistant to heat and moisture. The pipes are then embedded in the panels, and a layer of plaster is applied over the pipes. The SpeedUp Eco Wall Heating system can be used with any type of flooring, and it can be installed under carpets, tiles, or hardwood floors. It is also compatible with most types of wall coverings, including paint, wallpaper, and fabric.

Wet Plaster
1 Wall heating dowel, 3-part, 70 mm
2 Danfoss wall heating metalgrid
3 SpeedUp Eco panel, 30 mm
4 Danfoss composite pipe 16 x 2 mm
5 Heating plaster over SpeedUp Eco, 15 mm
Technical Data
Wall heating with wet plastering
Wall covering 15 mm Heating plasters over SpeedUp Eco; single layer
plastering, edge insulation strips required
Construction thickness 45 mm Dimensions without unfinished wall, without tiles
Thermal resistance (R) 0.75 m²K/W Thermal resistance value for SpeedUp Eco panel
Pipe spacing 125-250 mm EZ = 125; CZ = 250;
Requirements
and specialities
Heating plasters must show a good thermal conductivity. Light plasters and heat
insulation plasters are not suitable. Surface smoothness +/- 3 mm per 1m.
Observe building regulation requirements concerning thermal insulation.
Moisture condensation can occur and should be taken into consideration when
planning wall heating on outer walls and walls between heated and unheated
rooms.
Wall coverings Heating plasters:
Cement-lime plaster e.g. Stud: MP75 G/F, MP75 G: Thermal conductivity: 0.58 W/
mk; single layer processing; max. VL temperature: 50°C; heating according to
report possible after 3rd day.
Loam rendering e.g. Claytec: Final coat (05.010 / 05.012 / 10.012); Thermal
conductivity: 0.65 W/mK; single layer processing; max. VL temperature: 50°C;
heating possible immediately.
Chalk-cement plaster e.g. MARMORIT ROTKALK; biorit 110: Thermal conductivity:
0.87 W/mK; two-layer processing; max. VL temperature: 65 - 70°C; heating
according to report possible after 8 days.
Construction Referring to EN 1264.
Construction number 613
Application Sheet
SpeedUp Eco Wall Heating - Wet Plaster
Danfoss Heating Solutions VAEUL202 © Danfoss 03/2011 1
Application Sheet SpeedUp Eco Wall Heating - Wet Plaster
Danfoss A/S
Heating Solutions
Haarupvaenget 11
8600 Silkeborg
Denmark
Phone:+45 7488 8000
Fax: +45 7488 8100
Email: [email protected]
www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
2 VAEUL202 © Danfoss 03/2011 Danfoss Heating Solutions
  • Page 1 1
  • Page 2 2

Danfoss SpeedUp Eco Wall Heating - Wet plaster User guide

Danfoss
Brand
Danfoss
Model
SpeedUp Eco Wall Heating - Wet plaster
Type
User guide

Danfoss SpeedUp Eco Wall Heating - Wet plaster

The Danfoss SpeedUp Eco Wall Heating - Wet plaster is a system for heating your home using hot water pipes embedded in the walls. It is a cost-effective and energy-efficient way to heat your home, and it can be used in both new and existing buildings. The system consists of a series of panels that are attached to the walls. The panels are made of a lightweight, durable material that is resistant to heat and moisture. The pipes are then embedded in the panels, and a layer of plaster is applied over the pipes. The SpeedUp Eco Wall Heating system can be used with any type of flooring, and it can be installed under carpets, tiles, or hardwood floors. It is also compatible with most types of wall coverings, including paint, wallpaper, and fabric.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents