English-1

© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |

TP200 Rev. A

004-1080-00 Rev. A (9/13)

Pre-installation Guide for VetPro

®

5000 Dental System

Note

Please allow time for basic equipment training after the installation (approx 10 minuntes) The complete training is available

in-service. To schedule an in-service please contact Vet Customer Service at Midmark, 1-800-Midmark (1-800-643-6275).

3. Is power available? ______________________

Note: Review power requirements within this pre-install guide.

4. If “NO” to Q.3 what date will the power be available? ______________

5. Will this be a dedicated line?____________Midmark strongly recommends a dedicated line.

Note: Electrician will need a template to determine exact location for the electrical wiring to be installed when using a junction

box.

6. Is there anything that might interfere with the dental system in its home position? _________________________________

Refer to minimum space requirements in this guide.

7. Is the stud material wood or metal? ________________

Note: Site must have two studs available to complete the install for wall mounted units.

English-2

© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |

Mounting Structure Note: The mounting structure must be capable of supporting the

weight and torque listed below without deection.

Cabinet or Wall

Note

WHIP head folded against wall measures 30.6” from center of main axis to outermost point.

Water Module

Reservoir One - 1 Liter

Circuit Breaker Protection 15 amps

Frequency 60 Hz

English-3

© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |

English-4

© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |

Equipment Alert

When installing 115 VAC receptacle in the junction box,

the ground must be positioned as shown on diagram/template

(in this manual) to accommodate power cord.

Electrical Requirements

• Manual shut off valve ( supplied by Midmark) to be installed by contractor.

• Water pressure must be 30-50 (max.) PSI at the shut-off valve. Flush water plumbing clean before

making final connections to dental equipment.

Air Supply Requirements

• 1/2” (13 mm) pipe (supplied by contractor) protruding 2” (51 mm) from

finished surface of floor.

• Manual shut off valve ( supplied by Midmark) to be installed by contractor.

• Air pressure must be 80 - 100 (max.) PSI at the shut-off valve.

• Flush air plumbing clean before making final connections to dental equipment.

English-5

© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |

Note: Full Size Templates is included with Junction Box

English-6

© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |

Fan

Electrical

Voltage 115 VAC

Frequency 60 Hz

Circuit Breaker Protection 15 amps

Hospital Grade Wiring NEMA type: 14 and 18 AWG

Receptacles (Internal) NEMA Outlet, Snap AC Connector,

Air Tank 1 gal 3.79 Liter

Water Connection

Water Inlet Length 10 ft. (3 m)

Water Inlet Thread Size 3/8” FNPT

Saddle Valve Adapter Length 2 ft. (.61 m)

Saddle Clamp Range

3/8” - 1