H3C LSQM1WCMX40 User manual
- Category
- Access control readers
- Type
- User manual
Manual version: 6PW102-20170531 BOM: 3123A1E1
i
H3C LSQM1WCMX40 access controller module
1 Card identifier
The card identifier LSQM1WCMX40 is at the upper right corner of the front panel.
2 Introduction
The LSQM1WCMX40 high performance access controller module is developed for H3C
S7500E/S7600 switches. The card provides functions including access control, wireless security,
wireless user authentication, RF analysis, content filtering, and NAT. Equipped with this card, the switch
can provide wired and wireless services without network topology changes.
3 Specifications
The card has one console port and one 100/1000Base-T out-band management Ethernet port.
Figure 1 Front panel
(1) Captive screw
(2) Ejector lever
(3) 100/1000Base-T out-band mana
g
ement Ethernet port
(4) 100/1000Base-T out-band management Ethernet port LED (LINK/ACT)
(5) Console port (CONSOLE)
Table 1 Card specifications
Item S
p
ecification
CF card 4 GB
SDRAM 32 GB
Dimensions (H × W × D) 40.1 × 399.2 × 354.5 mm (1.58 × 15.72 × 13.96 in)
Power consumption 125 W to 180 W
Weight 4 kg (8.82 lb)
Hot swapping Supported
Ports
• One console port
• One 100/1000BASE-T out-band management Ethernet port.
Ambient temperature
• Operating: 0°C to 45°C (32°F to 113°F)
• Not operating: –40°C to +70°C (–40°F to +158°F)
Manual version: 6PW102-20170531 BOM: 3123A1E1
ii
Item S
p
ecification
Ambient relative humidity
• Operating: 10% to 95%, noncondensing
• Non-operating: 5% to 95%, noncondensing
Compatible device models
• H3C S7503E/S7506E-V/S7506E/S7510E/S7506E-NP
• H3C S7603/S7606/S7606 -NP/S7606-V/S7610
System software version See the release notes that come with the card.
Table 2 Console port specifications
Item S
p
ecification
Connector RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤ 15 m (49.21 ft)
Services
• Provides connection to an ASCII terminal.
• Provides connection to the serial port of a local PC running terminal
emulation program.
• Supports command line interface (CLI)
Table 3 100/1000BASE-T out-band management Ethernet port specifications
Item S
p
ecification
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Supported cable Category-5 (or above) twisted pair cable
Transmission distance ≤ 100 m (328.08 ft)
Operating mode
• 100 Mbps, half/full duplex
• 1000 Mbps, full duplex
4 LEDs
Table 4 LED description
LED Status
Descri
p
tion
100/1000BASE-T out-band
management Ethernet port LED
(LINK/ACT)
Off No link is present on the port.
Steady green A link is present on the port.
Flashing green The port is sending or receiving data.
Manual version: 6PW102-20170531 BOM: 3123A1E1
iii
5 Installing and removing the card
CAUTION:
• Wear a reliably-grounded ESD wrist strap or ESD gloves before you install or remove the card.
• Do not touch the components on the PCB.
The slots on the H3C S7500E/S7600 switches are either horizontally oriented or vertically oriented.
When installing the card in a horizontal slot, make sure its PCB faces up. When installing the card in a
vertical slot, make sure its PCB faces left.
This section uses a horizontally-oriented card to describe the installation and removal procedures.
5.1
Installing the card
1. Face the front panel of the switch. Remove the filler panel from the target slot.
2. Place the card horizontally with the PCB facing up. Pull outward the ejector levers on the card and
gently push the card into the slot along the guide rails.
3. Push the ejector levers inward so that the card is in close contact with the backplane.
4. Use a Phillips screwdriver to tighten the captive screws on the card.
Figure 2 Installing the card
Manual version: 6PW102-20170531 BOM: 3123A1E1
iv
5.2
Removing the card
1. Use a Phillips screwdriver to loosen the captive screws on the card until all pressure is released.
2. Pull the ejector levers at both sides of the card outward to separate the card from the backplane,
and pull the card slowly out of the chassis along the guide rails.
3. Place the card on an anti-static workbench with the PCB facing up, or put it in an anti-static bag.
4. If you are not to install a new card, install a filler panel in the slot to prevent dust and ensure good
ventilation in the switch.
6 Logging in to the card
The card uses an independent operating system. Before you can configure the card, you must log in to
the card by using one of the following methods:
• Log in from the switch's CLI through the oap connect command.
• Log in through the card's Web interface, console port, Telnet, SSH, or SNMP.
As a best practice, log in to the card from the switch's CLI the first time you access the card. For more
information about other login methods, see the configuration guides that come with the card.
To log in to the card from the switch's CLI, perform the following task in user view:
Task Command Remarks
Log in to the card
through OAP.
• In standalone mode:
oap connect slot slot-number
• In IRF mode:
oap connect chassis chassis-number slot slot-number
To return to the CLI interface
of the switch, press Ctrl+K.
7 Software upgrade
The card uses independent BootWare and system software images. You must upgrade the card software
separately from the switch software. To ensure a successful card upgrade, upgrade the card through the
card's console port or management Ethernet port as a best practice. For more information about
software upgrade of the card, see the release notes that come with the card.
8 Obtaining documentation
To access the most up-to-date H3C product documentation, go to
http://www.h3c.com.hk/Technical_Documents
For software upgrade, see the release notes for the device.
To access the release notes, go to
http://www.h3c.com.hk/Software_Download
Copyright © 2017 New H3C Technologies Co., Ltd.
-
1
-
2
-
3
-
4
H3C LSQM1WCMX40 User manual
- Category
- Access control readers
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
H3C LSQM1EPSB0 User manual
-
-
H3C H3C S7500E-X Command Reference Manual
-
H3C S12500-X User manual
-
H3C SecPath AC2500 User manual
-
-
-
-
-