H3C S12500-X User manual

Brand: H3C

Model: S12500-X

Type: User manual

This manual is also suitable for

LSU1FWCEA0

H3C S12500-X is a high-performance core/aggregation switch designed for large-scale data centers and enterprise networks. It provides high-density 10/25/40/100/400GbE ports, flexible stacking capabilities, and comprehensive Layer 2/3 features, making it ideal for building scalable and resilient network infrastructures. Its advanced features include:

High-density ports: Up to 128x 10/25/40/100GbE ports or 32x 400GbE ports in a compact 1U form factor, providing flexible connectivity options for various applications.
High-performance architecture: Based on advanced ASIC technology, the S12500-X delivers exceptional throughput, low latency, and non-blocking performance, ensuring smooth and reliable data transmission.

High-density ports: Up to 128x 10/25/40/100GbE ports or 32x 400GbE ports in a compact 1U form factor, providing flexible connectivity options for various applications.
High-performance architecture: Based on advanced ASIC technology, the S12500-X delivers exceptional throughput, low latency, and non-blocking performance, ensuring smooth and reliable data transmission.

Manual version: 6PW103-20141219 BOM: 3123A0MR

H3C LSU1FWCEA0 Card Manual

1 Card identifier

The card identifier LSU1FWCEA0 is at the upper right corner of the front panel.

2 Introduction

The LSU1FWCEA0 card provides one console port, one CF card interface, two USB interfaces, two

10/100/1000BASE-T Ethernet copper interfaces, and two Gigabit Combo interfaces.

You can use a combo interface to provide the following functions:

• In-band management.

• Outgoing interface for log messages.

• Failover interface for stateful failover.

3 Specifications

Figure 1 Front panel

(1) Console port (CONSOLE) (2) USB ports (hardware reserved, software not

support

currently)

(3) 10/100/1000BASE-T copper combo port (4) 10/100/1000BASE-T copper combo port LED

(LINK/ACT)

(5) 1000BASE-X fiber combo port (6) 1000BASE-X

fiber combo port LED (LINK/ACT)

(7) Alarm LED (ALM) (8) System LED (RUN)

(9) Ejector lever (10)

Captive screw

Table 1 Card specifications

Item S

ecification

Flash 4 MB

Memory

DDR3 SDRAM

2 memory slots

Standard: 4 GB (two 2-GB memory cards)

CF card

One built-in CF card slot

Default: 256 MB

Dimensions (H × W × D) 40.1 × 399.2 × 376.8 mm (1.58 × 15.72 × 14.83 in)

Power consumption

109 W to 157 W

Manual version: 6PW103-20141219 BOM: 3123A0MR

Item S

ecification

Weight 3.9 kg (8.60 lb)

Hot swapping Supported

Interfaces

• 1 console port

• 2 USB ports (hardware reserved, software not support)

• 2 combo interfaces, which can operate in 10/100/1000BASE-T copper port

mode or 1000BASE-X SFP fiber port mode at a time.

You can use the combo enable { copper | fiber } command to activate either

port. By default, the copper combo port is activated.

Ambient temperature

• Operating: 0°C to 45°C (32°F to 113°F)

• Not operating: –40°C to +70°C (–40°F to +158°F)

Ambient relative humidity

• Operating: 10% to 95%, noncondensing

• Non-operating: 5% to 95%, noncondensing

Compatible device models

and slots

• S10500 switches ( For the card to operate correctly, do not install the card in

slots 4 to 9 of the S10510 )

• S7600-X switches ( For the card to operate correctly, do not install the card in

slots 4 to 9 of the S7610-X )

• S7500E switches

• S7600 switches

• SR8800-X routers

System software version See the release notes that come with the card.

Table 2 Console port specifications

Item S

ecification

Connector RJ-45

Interface standard RS-232

Transmission baud rate 9600 bps (default) to 115200 bps

Transmission medium Asynchronous serial cable

Transmission distance ≤15 m (49.21 ft)

Services

• Provides connection to an ASCII terminal.

• Provides connection to the serial port of a local or remote (through a

pair of modems) PC running terminal emulation program.

• Supports command line interface (CLI)

Table 3 10/100/1000BASE-T copper port specifications

Item S

ecification

Connector RJ-45

Interface standard 802.3, 802.3u, and 802.3ab

Interface type MDI/MDIX autosensing

Supported cable Category-5 (or above) twisted pair cable

Transmission distance 100 m (328.08 ft)

Manual version: 6PW103-20141219 BOM: 3123A0MR

iii

Item S

ecification

Port transmission rate

• 10 Mbps, half/full duplex

• 100 Mbps, half/full duplex

• 1000 Mbps, full duplex

Table 4 1000BASE-X fiber port specifications

Item S

ecification

Transceiver module SFP

Connector type LC

Interface standard 802.3, 802.3u, and 802.3ab

Operating mode 1000 Mbps, full duplex

Table 5 1000BASE-X SFP port specifications

Gigabit SFP module

Central

wavelength

Connector

Cable specifications

Maximum

transmission

distance

SFP-GE-SX-MM850-A 850 nm LC

62.5/125μm

multi-mode optical fiber

0.55 km (0.34 miles)

SFP-GE-LX-SM1310-A 1310 nm LC

9/125 μm single-mode

optical fiber

10 km (6.21 miles)

SFP-GE-LH40-SM1310 1310 nm LC

9/125 μm single-mode

optical fiber

40 km (24.86 miles)

SFP-GE-LH40-SM1550 1550 nm LC

9/125 μm single-mode

optical fiber

40 km (24.86 miles)

SFP-GE-LH70-SM1550 1550 nm LC

9/125 μm single-mode

optical fiber

70 km (43.5 miles)

SFP-GE-LH100-SM1550 1550 nm LC

9/125 μm single-mode

optical fiber

100 km (62.14 miles)

4 LEDs

The card provides LEDs to show the operating status of the card and interfaces.

Table 6 LED description

LED Status Descri

tion

Alarm LED (ALM)

Off The system is operating correctly.

Steady red

The system is in an alarm condition, and immediate

action is required.

To identify the problem, use the system log.

Manual version: 6PW103-20141219 BOM: 3123A0MR

LED Status Descri

tion

System LED (RUN)

Off No power is input, or the card is faulty.

Steady green The system is not operating correctly.

Flashing green (1 Hz) The system has started up and is operating correctly.

Flashing green (8 Hz) The system is loading the software or is not ready.

Combo interface LED

(LINK/ACT)

Off No link is present on the port.

Steady green A link is present on the port.

Flashing green The port is sending or receiving data.

5 Installing and removing the card

CAUTION:

• Wear a well-grounded ESD wrist strap or ESD gloves before you install or remove the card.

• Do not touch the components on the PCB.

5.1

Installing the card

1. Remove the filler panel from the slot for the card at the front of the switch.

This example uses slot 7.

2. Place the card vertically with the surface-mounted components facing left. Pull the ejector levers

outward, and then gently push the card in along the slot guide rails until the card is in close contact

with the backplane.

3. Push the ejector levers inward.

4. Tighten the captive screws with a Phillips screwdriver to secure the card in the slot.

Manual version: 6PW103-20141219 BOM: 3123A0MR

Figure 2 Installing the card

5.2

Removing the card

1. Use a Phillips screwdriver to loosen the captive screws at both sides of the card.

2. Pull the ejector levers at both sides of the card outward to separate it from the backplane, and then

pull the card along the guide rails to remove it from the chassis.

3. Place the card on an anti-static workbench with the surface-mounted components up. You can also

put it in an anti-static bag.

4. If you are not going to install a new card, install a filler panel to prevent dust and ensure good

ventilation in the switch.

6 Logging in to the card

The card uses an independent operating system. Before you can configure the card, you must log in to

the card by using one of the following methods:

• Log in from the switch's CLI through the oap connect command.

• Log in through the card's Web interface, console port, Telnet , or SSH.

H3C recommends that you log in to the card from the switch's CLI the first time you access the card. This

section includes a procedure for logging in from the switch's CLI. For more information about other login

methods, see H3C SecPath Series Firewalls and UTM Devices Configuration Guides.

Manual version: 6PW103-20141219 BOM: 3123A0MR

To log in to the card from the switch's CLI, perform the following task in user view:

Task Command

Remarks

• In standalone mode:

oap connect slot slot-number

• In IRF mode:

oap connect chassis

chassis-number slot slot-number

To return to the CLI interface of the

switch, press Ctrl+K.

7 Software upgrade

The card uses independent BootWare and system software images. You must upgrade the card software

separately from the switch software. To ensure a successful card upgrade, H3C recommends that you

upgrade the card through the card's console port or management Ethernet port. For more information

about software upgrade of the card, see the release notes that come with the card.

8 Obtaining documentation

To access the most up-to-date H3C product documentation on the World Wide Web

at http://www.h3c.com

1. Go to http://www.h3c.com/Technical_Documents, or click Technical Support & Documents >

Technical Documents on the top navigation bar at http://www.h3c.com

2. Click Security Products > H3C SecBlade Module to choose the desired product category and

model.

The information in this document is subject to change without notice.

H3C S12500-X User manual

Brand: H3C

Model: S12500-X

Type: User manual

This manual is also suitable for

LSU1FWCEA0

High-density ports: Up to 128x 10/25/40/100GbE ports or 32x 400GbE ports in a compact 1U form factor, providing flexible connectivity options for various applications.
High-performance architecture: Based on advanced ASIC technology, the S12500-X delivers exceptional throughput, low latency, and non-blocking performance, ensuring smooth and reliable data transmission.

Download PDF

report

H3C S12500-X User manual

This manual is also suitable for

H3C S12500-X User manual

Related papers

Other documents