Rockwell Automation CENTERLINE 2100 LVMCC Product Notice

Brand
Rockwell Automation
Model
CENTERLINE 2100 LVMCC
Type
Product Notice
Product Safety Group
1201 South Second Street
Milwaukee, WI USA 53204
[email protected]
PRODUCT NOTICE
Notice of Potential Product Concern
Rockwell Automation issues a Product Notice when it identifies a product(s) anomaly that may cause commercial or customer
satisfaction concerns.
CENTERLINE 2100 LVMCC Fuse Clip Screws Under Torqued
Reference: 2015-05-001
Date: May 2015
This Product Notice informs you of a potential anomaly that exists with the CENTERLINE 2100 LVMCC using a
Bulletin 1494 disconnect switch or a 140M circuit breaker with fuses. Screws used to secure 30A through 400A fuse
clips to the disconnect switch may not have been tightened to the correct torque. Under torqued connections may
result in overheating at the connection.
PRODUCT NOTICE
Page 2 of 8
– Product Identification –
The affected products are CENTERLINE 2100 LVMCC systems using a Bulletin 1494 disconnect switch with 30A
through 400A fuse clips or 140M Circuit Breakers with 30A through 400A fuse clips. Affected systems were shipped
between January 1, 2011 and April 1, 2015.
CENTERLINE 2100 systems using a Bulletin 1494
disconnect switch with 30A or 60A cartridge fuse clips
and shipped between January 1, 2011 and April 1,
2015, are potentially affected.
CENTERLINE 2100 systems using a Bulletin 1494
disconnect switch with 100A through 400A cartridge
fuse clips and shipped between January 1, 2011 and
April 1, 2015, are potentially affected.
PRODUCT NOTICE
Page 3 of 8
CENTERLINE 2100 systems using a Bulletin 140M
circuit breaker with 30A through 400A cartridge fuse
clips and shipped between January 1, 2011 and April 1,
2015, are potentially affected.
Important – Systems using a Bulletin 194R disconnect switch are not affected by this anomaly.
CENTERLINE 2100 systems using a Bulletin 194R
disconnect switch are not affected by this anomaly.
The example image to the left shows a recent Bulletin
194R style disconnect switch. This image is an
example and may not be identical to that used in your
system. Older systems may use a previous style of
Bulletin 194R disconnect switch.
– Description –
This Product Notice informs you of a potential anomaly that exists with the CENTERLINE 2100 LVMCC. Screws
used to secure 30A through 400A fuse clips to both the 1494 disconnect and the corresponding trailer fuse block or
30A through 400A fuse clips used with a 140M circuit breaker may not have been tightened to the correct torque.
Under torqued connections may result in overheating at the connection. Continued overheating may result
discoloration of or damage to the fuse clip.
PRODUCT NOTICE
Page 4 of 8
On 100A through 400A fuse clip assemblies, the screws
are found under the locking clips on the fuse clip
assembly where the assembly is attached to the
disconnect switch and on the trailer fuse block. Note
there are two screws under each of the clips. The
screws may be marked with red ink.
The example images to the left show the two screws on
the disconnect side of the fuse assembly and the trailer
block side with the locking clip removed from one of the
fuse clips. There are twelve (12) total screws, six (6) on
the disconnect side and six (6) on the trailer block side.
On 30A through 60A fuse clip assemblies, the screws
are found under the fuse where the fuse clip attaches to
the disconnect switch or header fuse block and the
trailer fuse block. Note there is one screw for each of
the clips.
The example image to the left shows the screw with the
fuse removed. There are six (6) total screws, three (3)
on the disconnect or header block side and three (3) on
the trailer block side.
– Temporary Workarounds –
No workaround has been identified.
PRODUCT NOTICE
Page 5 of 8
– Correction –
ATTENTION: Only skilled personnel should oversee the maintenance and servicing of motor
control centers. If power sources are connected to the motor control center, use extreme caution
when inserting or removing units. All buses and the line sides of the units are energized and
contact with these parts can cause injury or death.
Follow NFPA 70E safety guidelines when working on energized equipment.
Correction requires re-torqueing the fuse clip screws to the correct torque level. Each fuse clip assembly has a
unique torque requirement. Refer to the following table for the correct torque.
Fuse Clip Rating
Target Torque (in-lbs)
Torque Range (in-lbs)
30A
30
27 to 33
60A
30
27 to 33
100A
20
18 to 22
200A
20
18 to 22
400A
30
27 to 33
Re-torqueing requires removal of the fuses from the fuse clip assembly.
1. Shutdown and lock-out tag-out (LOTO) the LVMCC system.
2. Open the system structure containing the disconnect switch and fuse clip assemblies.
3. Remove the fuses from the fuse clip assembly.
4. Depending on the type of fuse clip assembly –
For 30A and 60A assemblies, tighten the one
screw on each fuse clip on both the
disconnect side and the trailer block side of
the fuse assembly to the proper torque as
shown in the table above. There will be three
(3) total screws on the disconnect side and
three (3) total screws on the trailer block side.
PRODUCT NOTICE
Page 6 of 8
For 100A, 200A and 400A assemblies, tighten
the two screws under each fuse retaining clip
on both the disconnect side and the trailer
block side of the fuse assembly to the proper
torque as shown in the table above. There
will be a total of six (6) screws on the
disconnect side and six (6) screws on the
trailer block side.
Note – In the images to the left, only one fuse
clip assembly on the disconnect side and one
on the trailer block side have the retaining
clips removed for clarity. The screws are
located under the retaining clips. All retaining
clips must be removed to access the screws.
5. Re-install the fuses in the fuse clip assemblies.
6. Following proper electrical procedures, including LVMCC installation and start-up instructions, return power
to the LVMCC system.
During implementation of corrective action, if you observe evidence of overheating or damage to the fuse block
components or surrounding components, contact Rockwell Automation Technical Support. Be prepared to provide
your system MCC serial number and images of product overheating or damage. Reference this Product Notice PN
2015-05-001 when contacting Technical Support.
– Requested Customer Action –
Rockwell Automation requests you take the following actions:
Check if you have a product affected by this Product Notice. Refer to the Product Identification and
Description sections of this document for product identification assistance.
Follow the instructions in the Correction section of this document for your specific product type.
If you need additional assistance, please contact Rockwell Automation Technical Support. See Appendix A
for local telephone numbers. Customers without TechConnect contracts should reference this Product Notice
when calling.
Customers with TechConnect contracts may be able to chat online with support representatives. Reference
this Product Notice when connected to a support engineer.
The most current version of this Product Notice is posted on the Rockwell Automation Support Center,
http://www.rockwellautomation.com/knowledgebase, as ID number 703379. Additional languages may also
be available at the end of this article attached as downloadable PDF documents.
Customers using the Rockwell Automation Support Center in a non-English language should search for the
document by the article ID number listed above. The resulting article ID for non-English postings may be different
than the listed article ID number.
PRODUCT NOTICE
Page 7 of 8
If this Product Notice does not affect you because you do not have the products any longer, or if you are a Distributor,
Rockwell Automation asks that you forward a copy of this notice, with any identifying documentation, immediately to
the person or company that now has the product. We also ask that you contact Rockwell Automation Technical
Support and provide the location of the affected units.
We appreciate your immediate cooperation. If you have any questions, please contact us.
Sincerely,
ROCKWELL AUTOMATION
You can register for Automatic Product Safety Advisories and Product Notices from Rockwell Automation by email.
Go to the Support web page at http://www.rockwellautomation.com/support and click the Visit the Technical Support
Center link. Sign in with your Tech Connect Account or free Rockwell Automation Member Account and you can
subscribe to important product updates, including Product Safety Advisories and Product Notices.
PRODUCT NOTICE
Page 8 of 8
Appendix A
Regional Technical Support Information
The following list can help you to contact the correct technical support center for your location. If your country is not listed, you
can find a customer support number for your location on http://www.rockwellautomation.com/support/ by clicking Get Support
Now, selecting your country, and clicking the Phone/OnSite Support tab.
Region / Country
Phone Number
( ) International Code
Region / Country
Phone Number
( ) International Code
Asia/Pacific
Europe
Australia
1 800 762 593
Austria
(49) 211 41553 664
China
400 620 6620
Belgium
(32) 2 716 8411
Hong Kong
+852 2887 4666
Czech Republic
(420) 28401 5911
India
1 800 2000 121
Denmark
(45) 43 466 006
Japan
03 3206 2785
Finland
(358) 958 447 419
Korea
(82) 2 2188 4400
France
(33) 825303132
Malaysia
1 800 80 4851
Germany
(49) 211 41553 664
New Zealand
0800 27 27 25
Hungary
(420) 28401 5911
Taiwan
080 902 0908
Ireland
(44) 01908 635245
Thailand
(66) 2936 1500
Italy (Brescia, Milano e Padova)
(39) 199 11 99 00
Caribbean
Italy (Bologna,Firenze,Napoli,
Roma e Torino)
(39) 199 11 99 22
All Countries
(1) 440 646 3650
Morocco
(33) 825303132
Central America
Netherlands
(31) 10 266 55 80
Argentina
800.666.0320
Poland
(48) 22 32 60 707
Belize
(1) 440 646 3650
Portugal
(1) 440 646 3223
Bolivia
(54) 800 10 0632
Slovakia
(420) 284015911
Brazil
(55) 11 5189 9500
Spain
(34) 902 30 93 30
Chile
800.53.0012
Sweden
(46) 46 19 93 91
Colombia
01.800.700.2107
Switzerland (German)
(41) 0844 84 84 11
Costa Rica
0800.013.1215
Switzerland (French)
(41) 0844 84 84 12
Ecuador
58.212.949.0611
Switzerland (Italian)
(41) 0844 84 84 13
El Salvador
(52) 55 5246 2010
United Kingdom
(44) 01908 635245
Guatemala
(52) 55 5246 2010
North America
Honduras
(52) 55 5246 2010
Canada
(1) 440-646-3223
Mexico
001.888.365.8677
United States
(1) 440-646-3223
Nicaragua
(52) 55 5246 2010
Panama
001.800.203.3475
Paraguay
(54) 11 5554 4000
Peru
0800.535.36
Suriname
(1) 440 646 3650
Uruguay
(54) 11 5554 4000
Venezuela
800.1.00.3062
If you have a TechConnect Contract, please use the telephone number supplied to you with the contract.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Rockwell Automation CENTERLINE 2100 LVMCC Product Notice

Brand
Rockwell Automation
Model
CENTERLINE 2100 LVMCC
Type
Product Notice
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents