2. none
  3. 181990

none 181990 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the none 181990 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
To complete your project, you will also need:
•Drilldriverwith1/4”and1/8”drillbits
•7/16”wrench
•Tapemeasure,pencil/markerandsafetyglasses
•treatedwoodpost
Planning
•Priortoconstruction,checkwithyourlocalregulatoryagency
forspecialcoderequirementsinyourarea.
•Contactyourutilitysuppliertolocateandmark
undergroundlines.
•Carefulplanningandmeasuringofyourfenceprojectis
essential,asmovingpostsaftertheconcretesetsis
extremelydifcult.
Digging Post Holes
•Digpostholeforthehingepost18”to24”indiameterand
36”to42”deep(dependingonlocalordinanceorexpected
frostdepthinwinter).Werecommendthatyouinsertapieceof4x4treatedlumbertosupportthegatehingepost.
SeeFig.1.
•Actualgatesizewillvary.Theinsidepost–to-postdimensionwillbethewidthofthegateplus1-1/4”.
Double-check all measurements!
Assembling and Installating the Gate
•Measuretobesureyoucaninstallthegatetothepostwithapproximatelya2”gapfromthegroundtothebottomof
thegate.Aligntherailsonthegatetotherailsonthefencepanels.
•Layallgatecomponentsoutonaat,cleansurface.
•Placegatejambsonbothsidesoftherailsandplacethehingesinthecenterofthefencerail.Usingthehingeasa
guide,drillthefour(4)necessary¼”holesforthehingebolts.Ensuretherailsarefullyinsertedinthejambbefore
drilling.Theboltsneedtogothroughthejambandrailtofunctionproperly.SeeFig.2.
•Slidethehingedbracketandbracketonthetopandbottomofthegatejambs.Attachhingestojambswiththe
suppliedthroughbolts.Connectboltswiththesuppliedcapnuts.Ensurethegateissquarebeforeallboltsaretight.
Whensquare,tightenallboltswith7/16”wrench.SeeFig.2.
•Hangthegatebetweentheposts.Usea5/8”spacerbetweenthegateandtheposts.SeeFig.3.Secureinplacewith
shimsunderthegateorclampthejambonthegatetothepost.Makesurethegateislevelandsquare.Attachhinge
bracketstothegatepostwiththeprovidedscrews.SeeFig.4.
•Removeanyclampsandshims.Attachlatchusingscrews
provided.SeeFig.5.
•InstallapostcaponeachpostusingPVCcementoran
exterioradhesive.
Pro Series Privacy Gate
Installation Tips
fig. 2
5/8
Fig.4 DoverGateSpacer.ai
fig. 3
Note:Thegatelatchisdesignedtobeusedontheleftorrighthandsideofthegate,dependingoncustomerpreference
ordesign.Thelatchisassembled,readytobeinstalledontherighthandsideofthegate.Ifyoudesiretoswitchthelatch
followthesesimplesteps:
•Removethe2shoulderboltsandspring.
•Changeorientationoftheclicker
•Re-attachspringandinsertshoulderbolts.
•Shoulderboltsmustbefullytightened.Threadlockingadhesiveisrecommended.
Latch
Striker
Fig.6 DoverLatch.ai
fig. 5
Customer Service
855-556-1852
www.ufpi.com
Thediagramsandinstructionsshownareforillustrationpurposesonlyandarenotmeanttoreplacealicensedprofessional.Anyconstructionoruseoftheproductmustbein
accordancewithalllocalzoningand/orbuildingcodes.Theconsumerassumesallrisksandliabilityassociatedwiththeconstructionoruseofthisproduct.Theconsumeror
contractorshouldtakeallnecessarystepstoensurethesafetyofeveryoneinvolvedintheproject,including,butnotlimitedto,wearingtheappropriatesafetyequipment.
EXCEPTASCONTAINEDINTHEWRITTENLIMITEDWARRANTY,THEWARRANTORDOESNOTPROVIDEANYOTHERWARRANTY,EITHEREXPRESSORIMPLIED,ANDSHALL
NOTBELIABLEFORANYDAMAGES,INCLUDINGCONSEQUENTIALDAMAGES.
©2012UniversalForestProducts,Inc.Allrightsreserved.6367PrivGate_4/13
fig. 4
Page is loading ...
Servicio al Cliente
855-556-1852
www.ufpi.com
Losdiagramasylasinstruccionesquesemuestransonsóloparanesilustrativosynosustituyenaunprofesionalconlicencia.Cualquierconstrucciónousodelproductodebe
estarenconformidadcontodosloscódigoslocalesdezonicacióny/odeconstrucción.Elconsumidorasumetodoslosriesgosyresponsabilidadesasociadosconlaconstruc-
ciónoelusodeesteproducto.Elconsumidorocontratistadebetomartodaslasmedidasnecesariasparagarantizarlaseguridaddetodoslosinvolucradosenelproyecto,
incluyendo,peronolimitadoal,usodelequipodeseguridadapropiado. EXCEPTOPORLOQUESEINDICAENLAGARANTÍALIMITADAPORESCRITO,ELGARANTENO
OFRECENINGUNAOTRAGARANTÍA,EXPRESAOIMPLÍCITA,YNOSERÁRESPONSABLEPORNINGÚNDAÑO,INCLUSODAÑOSCONSECUENTES.
©2012UniversalForestProducts,Inc.Todoslosderechosreservados.6367PrivGate_4/13
Pestillo
Fig.6 DoverLatch.ai
Plancha
de cerradura
fig. 5fig. 4
Nota:ElpestillodepuertaDoverestádiseñadoparaserutilizadoenelladoizquierdooderechodelapuerta,dependiendode
lapreferenciadelclienteodeldiseño.Elpestilloestámontado,listoparaserinstaladoenelladoderechodela
puerta.Sideseacambiarelpestillosigaestossencillospasos:
•Quitelos2pernosdeajusteyelresorte.
•Cambielaorientacióndelclicker.
•Vuelvaacolocarelresorteeinsertelospernosdeajuste.
•Lospernosdeajustedebenestarbienapretados.Serecomiendaelusodeunadhesivobloqueadorderoscas.
/