Whirlpool AKR 951 IX WP Program Chart

Brand: Whirlpool

Model: AKR 951 IX WP

Category: Cooker hoods

Type: Program Chart

Whirlpool AKR 951 IX WP is a versatile kitchen appliance that combines effective extraction with the convenience of a built-in lighting system. Equipped with three speeds, it efficiently eliminates cooking odors and fumes, letting you maintain a fresh and clean cooking environment. The halogen bulbs provide bright illumination, ensuring clear visibility while you cook. Additionally, the grease filter is removable and dishwasher safe, making maintenance a breeze.

✂

5019 318

33095

AKR 951 - AKR 960

INSTALLATIONSBLAD

Minsta tillåtna avstånd från olika typer av spisar: 50 cm (elektrisk spis), 75 cm

(gasspis, gasolspis och koleldad spis). Följ givna anvisningar och

nummerordningen (1

.....) när fläktkåpan skall monteras. Slå inte på

strömmen till fläktkåpan förrän installationen är helt avslutad.

Rökröret och rörklämmorna som krävs för installationen levereras inte

tillsammans med fläktkåpan, utan måste köpas separat.

INSTALLASJONSVEILEDNING

Minimumsavstand til komfyrtopp: 50 cm (elektriske kokeplater), 75 cm (gass-,

parafin- eller kullkomfyr). Følg nummereringen ved montering (1

.....),

samt monteringsanvisningene. Apparatet må ikke tilkobles strømnettet før

installasjonen er helt avsluttet.

Merk! Avtrekksrøret og klemmene følger ikke med og må bestilles separat.

INSTALLATIONSVEJLEDNING

Minimumafstand fra kogezoner: 50 cm (elkogezoner), 75 cm (gas-, olie- eller

kulfyrede kogezoner). Ved montering skal man følge vejledningens

nummerrækkefølge (1

.....) og de tilhørende instruktioner. Apparatet må

ikke tilsluttes elforsyningen, før installationen er fuldført.

Advarsel! Aftræksrøret og spændebåndene leveres ikke med emhætten og skal

købes separat.

ASENNUSOHJEET

Vähimmäisetäisyys liedestä: 50 cm (sähkölevyt), 75 cm (kaasu-, öljy- tai

hiililiedet). Suorita asennus numerojärjestyksessä (1

.....) ohjeiden

mukaisesti. Älä kytke laitetta sähköverkkoon ennen kuin kokoonpano on

kokonaan suoritettu.

Huomaa! Poistoputkea ja kiinnittimiä ei toimiteta laitteen mukana, vaan ne on

hankittava erikseen.

INSTALLATION SHEET

Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or

coal cookers). To assemble follow the numbers (1

.....) and relative

instructions. Do not connect the appliance to the electrical power supply until

installation is completed.

Warning! The exhaust pipe and clamps are not supplied and must be bought

separately.

FIN

31833095.fm Page 1 Thursday, November 20, 2003 5:35 PM

✂

AKR 951 - AKR 960

5019 318

33095

14,5

273

244

214

190

31833095.fm Page 2 Thursday, November 20, 2003 5:35 PM

✂

5019 318

33095

AKR 951 - AKR 960

13A

13F

31833095.fm Page 3 Thursday, November 20, 2003 5:35 PM

✂

AKR 951 - AKR 960

5019 318

33095

31833095.fm Page 4 Thursday, November 20, 2003 5:35 PM

✂

5019 318

33095

AKR 951 - AKR 960

Preliminary information for installing the hood:

Expansion plugs are provided to secure the hood to most types of ceilings. A qualified technician is needed,

however, to make sure that the plugs are suitable for your ceiling. The ceiling must be strong enough to take

the weight of the hood.

Disconnect the power supply at the home main switch during electrical connections.

Adjust extension of the hood support structure, as the final height of the hood depends on this, and

remember that with installation completed the hood must be at least 50 cm above the cooktop in case of

electric cookers and 75 cm in case of gas or mixed cookers.

Fix the two sections of the structure using 8 screws.

Place the ceiling hole diagram directly above the cooktop (the centre of the diagram must match the

centre of the cooktop and the edges must be parallel to the sides of the cooktop - the side of the diagram

with the wording FRONT corresponds to the control panel side). Prepare the electrical connection.

Drill as shown (6 holes for 6 wall plugs - 4 plugs for hooking), screw the 4 outer screws leaving a space

of about 1 cm between the screw head and the ceiling.

Fit an exhaust pipe inside the truss and connect it to the collar of the motor compartment (exhaust pipe

and clamps are not provided).

Hook the truss to the 4 screws (see step 4).

CAUTION! The side of the truss with connection box corresponds to the side of the control panel with

hood assembled.

Tighten the 4 screws.

Insert and tighten another 2 screws in the remaining free holes for secure fixing.

Carry out the electrical connection to the mains power supply, only turn on the power supply with

assembly completed.

10.

Hook the hood to the truss, check for perfect hooking - to hook the hood to the truss partially screw 4

screws (also see step 12).

11.

Fixing the hood to the truss with two screws, will also facilitate centering the two parts.

12.

Tighten the 4 screws fixing the truss to the hood.

13.

For extractor operation (

13A

), connect the other end of the exhaust pipe to the home drain device.

For filter operation (

13F

), fit deflector

on the truss and fix it with 4 screws to the special bracket.

Finally, connect the exhaust pipe to the collar located on the deflector.

14.

Fit the nuts with fixing hooks supplied inside the top and bottom sections of the flues at the rectangular

slots. A total of 10 nuts must be fitted.

15.

Join the two top sections of the flue to cover the truss so that one of the slots on the sections is situated

on the same side of the control panel and the other on the opposite side.

Screw the two sections with 4 screws (2 each side - see the plan diagram for joining the two sections).

16.

Fix the top flue assembly to the truss, near the ceiling, with two screws (one each side).

17.

Carry out electrical connection of control panel and bulbs.

18.

Join the two bottom sections of the flue covering the truss using 6 screws (3 each side - also see the plan

diagram for joining the two sections).

19.

Insert the bottom section of the flue in the special seat to completely cover the motor compartment and

electrical connection box, and fix the hood with two screws from the inside.

20.

Apply the 2 tabs (supplied) to cover the fixing points of the bottom flue (CAUTION! THE BOTTOM FLUE

TABS ARE THE NARROWER AND SHALLOWER ONES).

The wider and deeper tabs are those used for the top flue, and must be cut to size.

21.

Turn the mains power on again at the central electrical panel and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

S N DK

FIN GB

31833095.fm Page 13 Thursday, November 20, 2003 5:35 PM

✂

AKR 951 - AKR 960

5019 318

33095

Control panel.

Grease filter.

Halogen bulbs.

Steam deflector.

Telescopic flue.

To clean the grease filter

Wash the grease filter at least once a month.

Disconnect the electrical power supply.

Remove the grease filters -

Fig. 1

: pull the spring

release handle

(f)

downwards, then remove the

filter.

After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface

is covered.

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

Disconnect the electrical power supply.

Remove the grease filter

(f - Fig. 1)

Turn the side knobs 90° and then remove the

filter holder

(g - Fig. 2)

Fit the carbon filter

(h - Fig. 2)

in the filter

holder

(i - Fig. 2)

Refit the filter holder and secure it to the hood

with the screw

(g - Fig. 2)

Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible,

using a normal dishwasher detergent. To avoid

particles of food or dirt settling on the filter during

washing and giving rise to unpleasant smells, it is

advisable to wash the filter on its own. After

washing, dry the filter in the oven at 100° C for 10

minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

Replacing bulbs

Disconnect the electrical power supply.

Use a small screwdriver or any other suitable tool

to prise off

(m-Fig. 3)

the lamp cover

(p-Fig. 3)

Remove the burnt-out bulb.

Replace using 20 W max halogen bulbs only,

making sure not to touch them with your hands.

Close the lighting unit (snap-close).

CONTROL PANEL

Light ON/OFF switch.

ON/OFF and speed 1 selector switch

(small amount of steam and fumes).

B+C.

Speed 2 selector switch

(medium amount of steam and fumes).

B+D.

Speed 3 selector switch

(large amount of steam and fumes).

ABCD

Fig. 1

Fig. 4

Fig. 2

Fig. 3

PRODUCT SHEET

S N DK

FIN GB

31833095.fm Page 14 Thursday, November 20, 2003 5:35 PM

Whirlpool AKR 951 IX WP Program Chart

Brand: Whirlpool

Model: AKR 951 IX WP

Category: Cooker hoods

Type: Program Chart

Download PDF

report

in other languages

dansk: Whirlpool AKR 951 IX WP

Whirlpool AKR 951 IX WP Program Chart

Whirlpool AKR 951 IX WP Program Chart

in other languages

Related papers

Other documents