Whirlpool AKR 948 IX Program Chart

Brand: Whirlpool

Model: AKR 948 IX

Category: Cooker hoods

Type: Program Chart

Whirlpool AKR 948 IX is a versatile kitchen appliance that combines powerful extraction with stylish design. With three-speed settings, it effectively removes steam, fumes, and odors, ensuring a fresh and clean kitchen environment. The halogen bulbs provide bright illumination for your cooking surface, while the carbon filter efficiently absorbs odors, creating a pleasant cooking experience. Cleaning and maintenance are a breeze, thanks to the dishwasher-safe grease filter and washable carbon filter.



5019 318 33080

AKR 948

INSTALLATIONSBLAD

Minsta tillåtna avstånd från olika typer av spisar: 50 cm (elektrisk spis), 75 cm

(gasspis, gasolspis och koleldad spis). Följ numreringen nedan för monteringen:

.....). Slå inte på strömmen till fläktkåpan förrän installationen är

helt avslutad. Observera! Rökröret och rörklämmorna (15) som krävs för

installationen levereras inte tillsammans med fläktkåpan, utan måste köpas

separat.

INSTALLASJONSVEILEDNING

Minimumsavstand til komfyrtopp: 50 cm (elektriske kokeplater), 75 cm (gass-,

parafin- eller kullkomfyr). Følg nummereringen ved montering (1

.....).

Apparatet må ikke tilkobles strømnettet før installasjonen er helt avsluttet.

Merk! Avtrekksrøret og festebåndene (15) følger ikke med og må anskaffes

separat.

INSTALLATIONSVEJLEDNING

Minimumafstand fra kogezoner: 50 cm (elkogezoner), 75 cm (gas-, olie- eller

kulfyrede kogezoner). Ved montering skal man følge vejledningens

nummerrækkefølge (1

.....). Apparatet må ikke tilsluttes elforsyningen,

før installationen er fuldført. Advarsel! Aftræksrøret og spændebåndene (15)

leveres ikke med emhætten og skal købes separat.

ASENNUSOHJEET

Vähimmäisetäisyys liedestä: 50 cm (sähkölevyt), 75 cm (kaasu-, öljy- tai

hiililiedet). Suorita kokoonpano numerojärjestyksessä (1

.....). Älä

kytke liesituuletinta sähköverkkoon ennen kuin kaikki asennusvaiheet on

suoritettu. Huomaa! Poistoputkea ja kiinnittimiä (15) ei toimiteta laitteen

mukana, ne on hankittava erikseen.

INSTALLATION SHEET

Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or

coal cookers). To install, follow points (1

.....). Do not connect the

appliance to the electrical power supply until installation is completed.

Warning! The exhaust pipe and clamps (15) are not supplied and must be bought

separately.

FIN

31833080.fm Page 1 Friday, June 6, 2003 3:45 PM



5019 318 33080

AKR 948

31833080.fm Page 2 Friday, June 6, 2003 3:45 PM



5019 318 33080

AKR 948

Preliminary information for installing the hood:

Disconnect the power supply at the domestic main switch before carrying out electrical connections.

1. Place the extraction unit on a flat surface and fit the bottom part of the hood on it

(remove the grease filter/s).

2. Carry out the electrical connections between the two parts.

3. Fix the hood to the extraction unit with 10 screws.

4. Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.

5. Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the

centre line drawn on the wall, and the lower edge of the hole diagram must match the lower edge of the

hood: remember that with installation completed the bottom of the hood must be at least 50 cm above

the cooktop in case of electric cookers and 75 cm in case of gas or mixed cookers.

6. Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two

external holes and drill, remove the hole diagram, insert 2 wall plugs and fix the hood support bracket

with two 5x45 mm screws.

7. Hook the hood to the bracket.

8. Adjust the distance between the hood and the wall.

9. Adjust the hood horizontally.

10. From inside the hood, mark the holes for fixing the hood permanently.

11. Remove the hood from the bracket.

12. Drill on the marks (Ø 8 mm - see step 10).

13. Insert 2 wall plugs.

14. Fit the flue support bracket G to the wall and against the ceiling, use the support bracket as hole diagram

(the small slot on the support must match the line drawn on the wall - step 4) and mark 2 holes with the

pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs.

15. Fix the flue support bracket to the wall with two 5x45 mm screws.

16. Hook the hood to the bottom bracket.

17. Fix the hood to the wall with two 5x45 mm screws (ABSOLUTELY NECESSARY).

18. Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar

B located above the extraction motor unit.

For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter

operation, fix the deflector F to the flue support bracket G with 2 screws and connect the other end of

the exhaust pipe to the deflector collar F (if the collar is not already fitted it should be inserted on the

deflector and secured with 1 screw). Once the steam and fumes have been filtered by the carbon filter

(not provided, to be ordered separately) they are conveyed back to the kitchen through grid H.

19. Carry out the electrical connection.

20. Apply the flues and fix them with 2 screws (20a) to the flue support G (20b).

21. Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction

unit.

Refit the grease filter/s and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

S DK FIN GB

31833080.fm Page 11 Friday, June 6, 2003 3:45 PM



5019 318 33080

AKR 948

1. Control panel.

2. Grease filter.

3. Halogen bulbs.

4. Steam deflector.

5. Telescopic flue.

To clean the grease filter

Wash the grease filter at least once a month.

1. Disconnect the electrical power supply.

2. Remove the grease filters - Fig. 1: pull the spring

release handle (f) downwards, then remove the

filter.

3. After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface

is covered.

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

1. Disconnect the electrical power supply.

2. Remove the grease filter (f - Fig. 1).

3. Turn the side knobs 90° and then remove the

filter holder (g - Fig. 2).

4. Fit the carbon filter (h - Fig. 2) in the filter

holder (i - Fig. 2).

5. Refit the filter holder and secure it to the hood

with the screw (g - Fig. 2).

6. Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible,

using a normal dishwasher detergent. To avoid

particles of food or dirt settling on the filter during

washing and giving rise to unpleasant smells, it is

advisable to wash the filter on its own. After

washing, dry the filter in the oven at 100° C for 10

minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

Replacing bulbs

1. Disconnect the electrical power supply.

2. Use a small screwdriver or any other suitable tool

to prise off (m-Fig. 3) the lamp cover (p-Fig. 3).

3. Remove the burnt-out bulb.

Replace using 20 W max halogen bulbs only,

making sure not to touch them with your hands.

4. Close the lighting unit (snap-close).

CONTROL PANEL

A. Light ON/OFF switch.

B. ON/OFF and speed 1 selector switch

(small amount of steam and fumes).

B+C. Speed 2 selector switch

(medium amount of steam and fumes).

B+D. Speed 3 selector switch

(large amount of steam and fumes).

Fig. 1

Fig. 4

Fig. 2

Fig. 3

PRODUCT SHEET

S DK FIN GB

31833080.fm Page 12 Friday, June 6, 2003 3:45 PM

Whirlpool AKR 948 IX Program Chart

Brand: Whirlpool

Model: AKR 948 IX

Category: Cooker hoods

Type: Program Chart

Download PDF

report

in other languages

dansk: Whirlpool AKR 948 IX

Whirlpool AKR 948 IX Program Chart

Whirlpool AKR 948 IX Program Chart

in other languages

Related papers

Other documents