H3C SecPath M9000-S NSQM2FWDFG0 User manual

Brand: H3C

Model: SecPath M9000-S NSQM2FWDFG0

Type: User manual

Manual version: 6PW103-20190904 BOM: 3123A1N4

H3C SecPath M9000-S NSQM2FWDFG0 firewall

module

1 Identifier

The module identifier NSQM2FWDFG0 is in the right side of the front panel.

2 About the module

The H3C fourth-generation high performance firewall module NSQM2FWDFG0 is developed for the

H3C M9000-S multiservice security gateway series. The module provides features including firewall,

VPN, content filtering, content identification, URL filtering, and NAT and can greatly enhance security

capabilities of the gateway.

3 Specifications

The module has a console port, a USB port, a GE copper port, and a hard disk slot.

Figure 1 Front panel

(1) Hard disk slot (reserved) (2) Console port (CONSOLE)

(3) Hard disk LED (HD) (reserved) (4) System status LED (SYS)

(5) USB port (reserved) (6) GE copper port (10/100/1000BASE-T)

(7) Ejector lever (8) Captive screw

Table 1 Module specifications

Item Specification

Flash 8 MB Nor Flash

Memory 64 GB DDR3 VLP RDIMM

Micro SD card

One built-in Micro SD card slot

Standard configuration: 8 GB

Dimensions (H × W × D) 40.1 × 399.2 × 354.8 mm (1.58 × 15.71 × 13.97 in)

Power consumption 185 W to 204 W

Weight 4.7 kg (10.36 lb)

Hot swapping Supported

1 2 3

4568 7

Manual version: 6PW103-20190904 BOM: 3123A1N4

Item Specification

Ports

• 1 × console port

• 1 × USB port (reserved)

• 1 × GE copper port

• 1 × hard disk slot (reserved)

Ambient temperature

• Operating:

{ Without hard disk: 0°C to 40°C (32°F to 104°F)

{ With hard disk: 5°C to 40°C (41°F to 104°F)

• Storage: –40°C to +70°C (–40°F to +158°F)

Rate of temperature change

• Operating with hard disk: < 20°C (68°F)/h

• Storage with hard disk: < 30°C (86°F)/h

Ambient humidity

• Operating:

{ Without hard disk: 5% RH to 95% RH, noncondensing

{ With hard disk: 10% RH to 80% RH, noncondensing

• Storage:

{ Without hard disk: 5% RH to 95% RH, noncondensing

{ With hard disk: 5% RH to 90% RH, noncondensing

Compatible device models and

slots

• M9008-S gateway with NSQM2MPUD0 MPUs installed (slots 2 to 5)

• M9012-S gateway (slots 0 to 4 and slots 7 to 10)

Table 2 Console port specifications

Item Specification

Connector RJ-45

Interface standard RS-232

Transmission baud rate 9600 bps (default) to 115200 bps

Transmission medium Asynchronous serial cable

Transmission distance ≤15 m (49.21 ft)

Services

• Provides connection to an ASCII terminal.

• Provides connection to the serial port of a local or remote (through a

pair of modems) PC running terminal emulation program.

• Supports command line interface (CLI)

Table 3 10/100/1000BASE-T Ethernet copper port specifications

Item Specification

Connector RJ-45

Interface standard 802.3, 802.3u, and 802.3ab

Interface type MDI/MDIX autosensing

Transmission medium Category-5 (or above) twisted pair cable

Transmission distance 100 m (328.08 ft)

Transmission rate and working

mode

• 10 Mbps, half/full duplex

• 100 Mbps, half/full duplex

• 1000 Mbps, full duplex

Manual version: 6PW103-20190904 BOM: 3123A1N4

iii

4 LEDs

The module provides LEDs to show the operating status of the module and the hard disk.

Table 4 LED description

LED Status Description

Hard disk (HD) (reserved)

Off The hard disk is not present or is faulty.

Fast flashing green The hard disk is reading and writing data.

Steady green The hard disk is operating correctly.

System status LED (SYS)

Off No power is being input or the module is faulty.

Slowly flashing green The system has started up and is operating correctly.

Fast flashing green The system is loading software.

5 Installing and removing the module

CAUTION:

• Wear a reliably-grounded ESD wrist strap or ESD gloves when you install or remove the module.

• Do not touch the components on the module.

5.1

Installing the module

1. Face the front panel of the device. Remove the filler panel from the target slot.

This example uses slot 2 on the device.

2. Place the module horizontally on a workbench with the PCB facing up. Open the ejector levers

on the module.

3. Gently push the module into the slot along the guide rails.

4. Close the ejector levers and make sure the module is in close contact with the backplane.

5. Use a Phillips screwdriver to fasten the captive screws on the module.

Manual version: 6PW103-20190904 BOM: 3123A1N4

Figure 2 Installing the module

5.2

Removing the module

1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is

released.

2. Simultaneously pull the ejector levers at both sides of the module outward to separate the

module from the backplane, and pull the module slowly out of the chassis along the guide rails.

3. Place the module on an anti-static workbench with the PCB facing up, or put it in an anti-static

bag.

4. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure

good ventilation in the device.

6 Software upgrade

For information about upgrading the module, see the release notes.

The information in this document is subject to change without notice.

H3C SecPath M9000-S NSQM2FWDFG0 User manual

H3C SecPath M9000-S NSQM2FWDFG0 User manual

H3C SecPath M9000-S NSQM2FWDFG0 User manual

Related papers

Other documents