Page is loading ...
Manual version: 6PW103-20190315 BOM: 3123A1LV
i
H3C SecPath M9000 NSQM1ADEDFGA0 application
delivery engine module
1 Identifier
The module identifier NSQM1ADEDFGA0 is at the upper right corner of the front panel.
2 About the module
The NSQM1ADEDFGA0 application delivery engine module is developed for H3C SecPath M9000
security gateways. It provides powerful traffic balancing and optimization capacity. You can install it
on an M9000 gateway at the aggregation or core layer of a data center to accelerate the response
time and enhance service continuity of the data center.
3 Specifications
The module has a console port, a USB port, a GE copper port, and a hard disk slot.
Figure 1 Front panel
(1) Captive screw (2) Ejector lever
(3) Hard disk slot (reserved) (4) Console port (CONSOLE)
(5) GE copper port (10/100/1000BASE-T) (6) USB port (reserved)
(7) Hard disk LED (HD) (8) System status LED (SYS)
Table 1 Module specifications
Item Specification
Flash 8MB Nor Flash
Memory
Eight memory slots
Standard configuration: 64 GB (Eight 8GB VLP RDIMMs)
You must install the VLP RDIMMs in pairs and each pair must have the same
specifications.
Micro SD card
One built-in Micro SD card slot
Standard configuration: 8 GB
Dimensions (H × W × D) 40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight 4.8 kg (10.58 lb)
Power consumption 180 W to 260 W
Hot swapping Supported
Manual version: 6PW103-20190315 BOM: 3123A1LV
ii
Item Specification
Interfaces
• 1 × console port
• 1 × USB port (reserved)
• 1 × GE copper port
• 1 × hard disk slot (reserved)
Ambient temperature
• Operating: 5°C to 40°C (41°F to 104°F)
• Storage: –40°C to +70°C (–40°F to +158°F)
Rate of temperature
change
• Operating: < 20°C (68°F)/h
• Storage: < 30°C (86°F)/h
Ambient relative humidity
• Operating: 10% RH to 80% RH, noncondensing
• Storage: 5% RH to 90% RH, noncondensing
Compatible gateway
models and slots
• M9006 gateway (slot 2 to slot 5)
• M9010 gateway (slot 0 to slot 3 and slot 6 to slot 9)
• M9014 gateway (slot 4 and slot 5 and slot 8 to slot 12)
NOTE:
To verify compatibility of the module with the software release you are using, see the release notes.
Table 2 Console port specifications
Item Specification
Connector RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
Services
• Provides connection to an ASCII terminal.
• Provides connection to the serial port of a local or remote (through a
pair of modems) PC running terminal emulation program.
• Supports command line interface (CLI)
Table 3 10/100/1000BASE-T copper Ethernet port specifications
Item Specification
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Supported cable Category-5 (or above) twisted pair cable
Transmission distance 100 m (328.08 ft)
Port transmission rate
• 10 Mbps, half/full duplex
• 100 Mbps, half/full duplex
• 1000 Mbps, full duplex
Manual version: 6PW103-20190315 BOM: 3123A1LV
iii
4 LEDs
The module provides LEDs to show the operating status of the module and the hard disk.
Table 4 LED description
LED Status Description
Hard disk (HD)
Flashing green The hard disk is reading and writing data.
Steady green The hard disk is operating correctly.
Off No hard disk is in position.
System status LED (SYS)
Off No power input or the module is faulty.
Slowly flashing green The system has started up and is operating correctly.
Fast flashing green The system is loading the software.
5 Installing and removing module
CAUTION:
• Wear a reliably-grounded ESD wrist strap or ESD gloves when you install or remove the module.
• Do not touch the components on the module.
The service module slots might be vertical or horizontal, depending on the gateway model. When
installing the module in a horizontal slot, make sure its component side faces up. When installing the
module in a vertical slot, make sure its component side faces left.
The module installation and removable procedures are the same for horizontal or vertical slots. The
following procedures install and remove the module in a horizontal slot.
5.1
Installing the module
1. Face the front panel of the gateway. Remove the filler panel from the target slot.
This example uses slot 3 on the M9006 gateway.
2. Place the module horizontally on a workbench with the PCB facing up. Open the ejector levers
on the module.
3. Gently push the module into the slot along the guide rails.
4. Close the ejector levers and make sure the module is in close contact with the backplane.
5. Use a Phillips screwdriver to fasten the captive screws on the module.
Manual version: 6PW103-20190315 BOM: 3123A1LV
iv
Figure 2 Installing the module
5.2
Removing the module
1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is
released.
2. Simultaneously open the ejector levers on the module to separate the module from the
backplane, and pull the module slowly out of the chassis along the guide rails.
3. Place the module on an anti-static workbench with the component side facing up, or put it in an
anti-static bag.
4. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure
good ventilation in the gateway.
6 Software upgrade
For information about upgrading the module, see the release notes.
Copyright © 2019 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
/