MOUNTUP MU1005 User manual

Brand: MOUNTUP

Model: MU1005

Category: Flat panel desk mounts

Type: User manual

Product Dimensions

Safety Caution

Installation Tools (Not Included)

Supplied Parts and Hardware

1 2

INSTALLATION INSTRUCTION

NOTE: Not all hardware included will be used.

If you have any questions, please feel free to contact Customer Service

via Amazon before returning.

(ZDT10-C02-M_US2)

Band Tape

2m Screwdriver

Bubble Level

Plastic CoverBolt

M6 x 30mm

Hardware (Product)

Washer Wire Clip

A B x1

Cx3

Ex4

Fx1

Foot Pad

Bolt

M6 x 10mm

Handle Bolt Allen Key

4mm / 5mm

CAUTION AND MAINTENANCE

• Never allow children to climb, stand, hang, or play on any part of monitor or stand.

• This product is intended for indoor use only. Using this product outdoors could lead to product

failure and personal injury.

• Check that the bracket is secure and safe to use at regular intervals (at least every three months).

WARNING

• This product contains small items that could be a choking hazard if swallowed.

• KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

• Improper installation, such as using the product for monitors over its load capacity or for any

purpose not explicitly specified, may cause damage or serious injury. We would not be liable for

any damage or injury caused by improper mounting or inappropriate use.

BEFORE ASSEMBLY

• Layout all components and hardware. Check all parts are included and undamaged.

• Should anybody intends to install or use this monitor stand, please read and understand this

manual carefully.

• If you do not understand these instructions or have any doubt about the safety instructions,

assembly or use of this product, please contact our customer service.

75x75mm

100x100mm

33 lbs

15 kg x1 x1

1 (×1)

Base

14 (×1)

Plate Component

2 (×1)

Support Pillar (Upper)

3 (×1)

Support Pillar (Lower)

3 (×1)

Connecting Plate

Hardware (Monitor)

Spacers

H13mm

MG x4

Philips Screws

M4 x 30mm

MB x4

Philips Screws

M5 x 16mm

MC x4

Philips Screws

M5 x 25mm

MD x4

Philips Screws

M4 x 12mm

MA x4 MF x4

Philips Screws

M6 x 25mm

Philips Screws

M6 x 16mm

Spacers

H5mm

MH x4

±45°

Swivel

360mm/14.17"

240mm

/9.45"

360°

Rotation

115mm

/4.53"

100mm

/4"

75mm

/3"

6.5mm/0.26"

MAX:

641mm/25.24"

MIN:

361mm/14.21"

720mm

/28.35"

±30°

Tilt

35mm/1.38"

280mm

/11"

35mm/1.38"

Table

STEP 2: Apply Foot Pads to the BaseSTEP 1: Support Pillar Installation

Hold the Support Pillar with one hand and tear off plastic film of Foot Pads (F), then

attach Foot Pads (F) near four conors of the Base bottom.

Put Base on the table; put Washers (B) and Bolts (A) on the base; keep clip holes of

Support Pillar toward backside then put Plastic Cover (D) and Support Pillar under

the base. Then tighten the bolts (A) with the 4mm allen key (G).

Note: Support pillar should

be placed with clip holes

facing backwards.

Table

Connect two Support Pillars ( 2 & 3 ) by using Connecting Plate and Bolts (H).

Use the 4mm allen key (H) to tighten the bolts.

3 4 5

Metal Washer

EVA Washer

STEP 6: Adjustments (If necessary)

STEP 4: Attach Monitor with Plate Component to Pillar

STEP 5: Cable Management

STEP 6: Adjustments (If necessary)

9 10 11

Attach Wire Clips (E) into the holes of Support Pillar. Manage cables with the Wire

Clips (E).

Support Pillar

+30°

-30°

Tilt Adjustment

1. Slightly loosen tilting bolt with the Allen Key(G).

2. Hold the monitor with both hands and adjust monitor to your desired tilt angle.

3. Retighten tilting bolt to secure the monitor in place.

Leveling Adjustment

Note:

When tilted, if the monitor sags or does not stay,

and if the above method is useless, please feel

free to contact our customer service.

Swivel Adjustment

STEP 3: Attach the Plate Component to Monitor

CorrectCorrectToo Short Too Long

When attaching plate to the flat screen, be careful not to over tighten

screws and be sure that screws do not bottom out in the mounting holes.

3-1 Select Monitor Screw Length

Thread screws by hand into the threaded holes on the back of your monitor and then

select which screw diameter fits your monitor.

STEP 3: (Continued)

Note: Keep the ARROW mark

pointing UPWARDS when

installing the plate component.

1.Choose the appropriate position for

your monitors, hang the monitors onto

the Support Pillar.

2.Rotate the monitor

facing toward the front.

3.Tighten them with

Handle Bolt (C).

Tighten

3-2 Attach the Plate Component

(a) For Flat Back Monitor

(b) For Recessed / Curved Back Monitor

Use the shorter screws

Use the long screws

MC MD

TOP OF MONITOR

NOTE: If the MA screw is a little long,

please use a H5mm spacer(M-H) to fix it.

MOUNTUP MU1005 User manual

Brand: MOUNTUP

Model: MU1005

Category: Flat panel desk mounts

Type: User manual

Download PDF

report

MOUNTUP MU1005 User manual

MOUNTUP MU1005 User manual

Related papers

Other documents