MOUNTUP MU0031 is a versatile TV stand designed to provide a secure and adjustable mounting solution for flat-screen TVs ranging from 32 to 65 inches and weighing up to 88 lbs. It features a sturdy metal construction with a black finish, offering a sleek and contemporary look to complement your home décor.
MOUNTUP MU0031 is a versatile TV stand designed to provide a secure and adjustable mounting solution for flat-screen TVs ranging from 32 to 65 inches and weighing up to 88 lbs. It features a sturdy metal construction with a black finish, offering a sleek and contemporary look to complement your home décor.
STEP 1: Attach the Brackets to TV STEP 1: (Continued)
1-3 Attach the TV Brackets
1-2 Select TV Screw Length
CorrectCorrectToo Short Too Long
When attaching plate to the flat screen, be careful not to over tighten
screws and be sure that screws do not bottom out in the mounting holes.
Product Dimensions
Safety Caution
Installation Tools (Not Included)
Supplied Parts and Hardware
1 2
3
4
INSTALLATION INSTRUCTION
NOTE: Not all hardware included will be used.
5
If you have any questions, please feel free to contact us via Amazon.
(YZ2210-US1) Band Tape
2m Screwdriver
2M
Bubble Level
1-1 Select TV Screw Length
Thread screws by hand into the threaded holes on the back of your TV after selecting
which screw diameter fits your TV.
M8
M6
No!
CAUTION AND MAINTENANCE
• Never allow children to climb, stand, hang, or play on any part of TV or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to product
failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
WARNING
• This product contains small items that could be a choking hazard if swallowed.
• KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
• Improper installation, such as using the product for monitors over its load capacity or for any
purpose not explicitly specified, may cause damage or serious injury. We would not be liable for
any damage or injury caused by improper mounting or inappropriate use.
BEFORE ASSEMBLY
• Layout all components and hardware. Check all parts are included and undamaged.
• Should anybody intends to install or use this TV stand, please read and understand this
manual carefully.
• If you do not understand these instructions or have any doubt about the safety instructions,
assembly or use of this product, please contact our customer service.
Min: 150x100mm / 6x4"
Max: 600x400mm / 24x16"
88 lbs
40 kg
RATED
TOP OF TV
May be needed
M-F
M-G M-H
Keep the arrow up
M-A M-B M-E
M-D
M-C
4
4
x4
ME
Philips Screws
M6 x 15mm
Philips Screws
M6 x 30mm
Philips Screws
M8 x 15mm
MC x4
MB x4
Hardware (TV)
MF x8
Spacers
H10mm
MH x8
Philips Screws
M8 x 45mm
MD x4
MA x4
Washer
Φ5 / Φ8
Philips Screws
M8 x 65mm
Bolt
M5x12mm
Nut
M5
Bolt
M6x30mm Washer
x3
Ax1
B
Bolt
M6x10mm
x4
E
Plastic Cover
x1
Fx2
G
Safety Lock Wire Clip
x2
Hx4
I
Foot Pad
MG x8
Spacers
H5mm
1 (×1)
Base
11 (×1)
Support Pillar
21 (×1)
Support Pillar
31 (×2)
TV Bracket
41 (×2)
TV Plate
51 (×1)
Connecting Plate
61 (×1)
Angle Adjuster
7
x4
C1
Bolt
M6x16mm
Flange Nut
M6
x4
C2
Bolt
M6x50mm
Washer
Φ6
x4
D1 x4
D2
x8
J1
Washer
Φ5.5
x8
J2 x8
J3
4mm Allen Key
Wrench
x1
K1
x1
K2
Socket Wrench
x1
K3
±25°
Swivel
MAX: 600mm/24"
MIN: 150mm/6"
MAX:
400mm/16"
MIN:
100mm/4"
400mm/15.76"
100mm/3.94"
Φ
8.5mm/0.33"
280mm
/11.02"
81mm/3.19"
54mm/2.13"
145mm/5.71"
MAX:
751.5mm/29.59"
MIN:
541.5mm/21.32"
751.5mm
/29.59"
701.5mm
/27.62"
696.5mm
/27.42"
646.5mm
/25.45"
641.5mm
/25.26"
591.5mm
/23.29"
541.5mm
/21.32"
High
Pillar
Bracket
Middle
Low
High Middle Low
651.5mm
/25.65"
596.5mm
/23.48"
+8°~0°
Tilt
16mm
/0.63"
548mm
/21.57"
90mm/3.54"
50mm/1.97"
50mm/1.97"
55mm/2.17"
55mm/2.17"
55mm/2.17"
641mm/25.24"
STEP 4: TV Plate Installation
STEP 3: Apply Foot Pads to the Base
STEP 7: Adjustments (If necessary)
STEP 2: Support Pillar Installation STEP 4:
(Continued)
4-3: Choose the appropriate position (three options) for your TV Plate, then connect TV Plate
Component to Support Pillar by using Bolts (D1) and Washers (D2). Use the 4mm allen key
(K1) to tighten them.
STEP 5: Attach TV with Brackets to TV Plate
8
STEP 6: Cable Management
9 10 11
76
Tilt Adjustment
Connect two Support Pillars ( 2 & 3 ).
23
Put Base on the table;
put Washer (B) and Bolts
(A) on the base; keep clip
holes of Support Pillar
toward backside then put
Plastic Cover (F) and
Support Pillar under the
base. Then tighten the
bolts (A) with the 4mm
allen key (K1).
1
3
3
E
K1
Table
Then insert 4pcs Bolts (E) through the holes of
Support Pillars ( 2 & 3 ), and use the 4mm Allen
Key (K1) to tighten.
2 3
Table
I
1
Hold the Support Pillar with
one hand and tear off plastic film
of Foot Pads (I), then attach Foot
Pads (I) near four conors of the
Base bottom.
3
1
A
B
F
K1
1
3
Note: Support pillar
should be placed with clip
holes facing backwards. 7
C2
(x4)
TV Plate
Unit
C1
(x4)
56
J2
(x8)
J1
(x8)
J3
(x8)
(x2)
4-1: Connect TV Plate and Connecting
Plate by using and M5 Bolts (J1),
Washers (J2) and Nuts (J3). Use the
Socket Wrench (K3) to tighten the nuts.
5
6
4-2: Connect TV Plate Unit and Angle
Adjuster by using and M6 Bolts (C1)
and Nuts (C2). Use the Wrench (K2) to
tighten the nuts.
7
Put the Safty Lock (G) in
place and tighten the fixing
screw to the plate securely.
G
Swivel Adjustment
-25°+25°
1. Slightly loosen tilting nuts with the
Wrech (K2).
2. Hold the TV with both hands and
adjust TV to your desired tilt angle.
3. Retighten tilting nuts to secure the
TV in place.
D1
(x4)
TV Plate Component
D2
(x4)
2
NOTE: Three choices
for height adjustment.
WARNING: TV Plate should
be installed with the ARROW
mark pointing UPWARDS.
UP
Choose the appropriate
position (three options)
for your TV.
Hang TV with brackets
onto the TV plate.
H
Attach Wire Clips (H) into the holes of
Support Pillar . Manage cables
with the Wire Clips (H).
23
+8°
0°
Note: When tilted, if the TV sags or
does not stay, and if the above method
is useless, please feel free to contact
our customer service.
K2 Loosen
Tighten
K2
K3
K1
50mm
50mm
55mm
55mm
55mm
3
-
1
-
2
MOUNTUP MU0031 is a versatile TV stand designed to provide a secure and adjustable mounting solution for flat-screen TVs ranging from 32 to 65 inches and weighing up to 88 lbs. It features a sturdy metal construction with a black finish, offering a sleek and contemporary look to complement your home décor.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
MOUNT PRO Universal TV Stand, Swivel TV Stand Base Fits Most 37 to 70 Inch LCD LED Screens, 9 Levels Height Adjustable Table Top TV Stand User manual
-
Trixter X-Bike User manual
-
Diamondback SHEPPARD CYCLES Owner's manual
-
Kanto P301 User manual
-
Milazo BMX User manual
-
Stamina CoreTraining Inversion System Owner's manual
-
Grace Company The GMQ-Pro User manual
-
Craftsman CRT/D User manual
-
Tendercare Snappi Pushchair Workshop Manual
-
Hyundai Elantra Body Repair Manual
