MOUNTUP MU4003 User manual

Brand
MOUNTUP
Model
MU4003
Category
Flat panel desk mounts
Type
User manual

MOUNTUP MU4003 is a versatile monitor mount compatible with most 32-inch monitors weighing up to 17.6 lbs (8 kg). It offers a wide range of motion, including 360-degree swivel, +45°/-45° tilt, and height adjustment along the 15.8-inch (403 mm) pole. This flexibility allows you to find the perfect viewing angle for your monitor, reducing neck and eye strain. The mount also features a cable management system to keep your workspace organized and a tool storage solution for the included Allen keys.

MOUNTUP MU4003 is a versatile monitor mount compatible with most 32-inch monitors weighing up to 17.6 lbs (8 kg). It offers a wide range of motion, including 360-degree swivel, +45°/-45° tilt, and height adjustment along the 15.8-inch (403 mm) pole. This flexibility allows you to find the perfect viewing angle for your monitor, reducing neck and eye strain. The mount also features a cable management system to keep your workspace organized and a tool storage solution for the included Allen keys.

Single Monitor Mount
Instruction Manual
MA08-10P-US1.0
75x75
100x100
8kg/17.6lbs
32"
If you have any questions, please feel free to contact us via Amazon.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
17.6 lbs
(8 kg)
B (x1)
Swivel Arm
C (x1)
Clamp
H(x1)
5mm Allen Key
I(x1)
6mm Allen Key
G(x1)
Bolt
A (x1)
VESA Plate
01
M-E(x4)
Washer D6mm
M-F (x4)
Spacer H5mm
M-C (x4)
M6 x 12mm
M-D (x4)
M6 x 16mm
M-B (x4)
M4 x 16mm
M-A (x4)
M4 x 12mm
If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper
installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specied,
may cause damage or serious injury. We would not be liable for any damage or injury caused by improper
mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF
CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
D (x1)
Pole
F (x2)
Bolt
E(x1)
Wire Clip
C1
Bracket
C2
Bolt Y
C3
Bolt
C4
Washer
C5
Clip Plate
All are included in C
ASSEMBLY STEPS
02
OPTION A: Clamp Installation
Mount Clamp (C) to the bottom of Pole (D) by tightening bolts (F) with 5mm Allen Key (H).
Adjust the Clamp width to t your desk. Secure stand to the desktop by tightening Clamp (C).
STEP 1: Clamp Installation OR Grommet Base Installation
D
C
F
H
10-50mm
0-1.97"
Warm Tips You could also refer to the Video Guide about installation on our product page.
STEP 1: (Continued)
03
OPTION B: Grommet Base Installation
If existing grommet hole comes with a plastic protector, remove it to ensure a at surface before installing
the desk mount.
Detach Bracket (C1) and Bolt Y (C2) from Clamp (C).
Position pole (D) on the mounting surface and then secure it by tightening the plastic knob after making
Bolt Y (C2) through the Bracket (C1), desk hole, and the bottom of Pole (D) sequentially.
DESK
DESK
ø 10~60mm
ø 0.39~2.36"
0-1.97"
C
C1 C2
10-50mm
C1 C2
D
STEP 2 : Arm Installation
04
Install wire clip (E) and swivel arm (B) to the pole (D). Fasten the bolt with supplied 6mm Allen key (I).
B
D
E
I
05
STEP 3: Attach Monitor
OPTION A: Flat Back Monitor
OPTION B: Curved Back Monitor
M-B
M-D
M-E
M-F
I
A
Attach the VESA plate (A) to back of monitor and
secure with screws(M-A)or(M-C) with washers(M-E)
using 6 mm Allen Key (I). Do not tighten the screws
excessively or your monitor might be damaged.
Monitor Monitor Monitor
Monitor Monitor Monitor
Attach the VESA plate (A) to back of monitor and secure
it with screws (M-B) or (M-D) and washers (M-E) and
spacers (M-F) using 6 mm Allen Key (I). Do not tighten
the screws excessively or it might damage your monitor.
M-A
M-C
M-E
I
A
No!
No!
STEP 4 : Hang Monitor
06
Slide monitor with VESA plate onto mounting bracket.
Secure with security bolt (G).
G
07
STEP 5: Tilt Adjustment
Tighten or loosen tilt joint using 6mm Allen Key (I).
STEP 6: Cable Management
Manage cables with installed Wire Clip (E).
I
E
+
-
Solution:
1. Loosen the tilting bolt.
2. Hold the bottom of monitor with
one hand and adjust to determine
your desired tilt angle.
3. Retighten the tilting bolt to x
the intended angle.
Problem:
If monitor face down.
Rotation
08
STEP 7: Tool Management
STEP 8: Adjust as Desired
Store 5mm Allen Key (H) and 6mm Allen Key (I) in Wire Clip (E).
Adjust monitor position and rotation.
+45°
-45°
±45°
360°
Tilt
Swivel
Rotation
Swivel
Tilt
H
E
I
09
Product Dimensions
114mm/4.48"
100mm/3.9"
75mm/2.9"
38mm
1.5"
50mm
1.96"
114mm
100mm
75mm
403mm / 15.8"
0mm - 50mm
0-1.97"
70mm,/4.13"
360°
-45°
+45°
±45°
CAUTION AND MAINTENANCE:
• Don't allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors may lead to
product damage or personal injury.
• Check if that the bracket is secure and safe to use at regular intervals
(at least every three months).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

MOUNTUP MU4003 User manual

Brand
MOUNTUP
Model
MU4003
Category
Flat panel desk mounts
Type
User manual

MOUNTUP MU4003 is a versatile monitor mount compatible with most 32-inch monitors weighing up to 17.6 lbs (8 kg). It offers a wide range of motion, including 360-degree swivel, +45°/-45° tilt, and height adjustment along the 15.8-inch (403 mm) pole. This flexibility allows you to find the perfect viewing angle for your monitor, reducing neck and eye strain. The mount also features a cable management system to keep your workspace organized and a tool storage solution for the included Allen keys.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents