2. Vehicles & accessories
  3. Motor vehicle accessories & components
  4. Motorcycle Accessories
  5. DIODE LED
  6. SABER™ LED Under Cabinet Light

DIODE LED SABER™ LED Under Cabinet Light, SABER™ LED Under Cabinet Light Accessories Installation guide

  • Hello! I've reviewed the SABER Under Cabinet Light installation guide and am ready to assist you. This document covers how to properly install and connect your new light, including important safety information and troubleshooting steps. It explains how to mount the fixture, connect it to either a plug-in or hardwired power source, and select your desired color temperature. How can I help you today?
  • What should I do if the lights are flickering?
    What should I do if the lights will not illuminate?
    Can I cut or shorten the fixture?
1 OF 4 IG041822-1.0
SABER™ Under Cabinet Light INSTALLATION GUIDE
®SABER™ Under Cabinet Light
INSTALLATION GUIDE
1. Do not puncture, cut, or shorten, xture. Doing so causes
risk of electric shock and will void the Safety Certication
and warranty.
2. Do not use if there is any damage to the xture or AC
cord insulation. Inspect periodically.
3. All plastics are aected by the elements and may shift
in color and other properties after product installation,
particularly with direct exposure to sun, chlorinated water,
and other chemicals.
4. Do not submerge xture in liquids or use the product in
the vicinity of standing water or other liquids.
5. Secure xture using only hangers or mounting clips
provided. Do not secure with staples, nails, its input
wire, or like means that may damage the insulation or
permanently attach the xture to a building structure.
6. Do not subject xture to continuous exing.
7. Do not install near water.
8. Do not install in direct sunlight or damage to the LED
phosphor will occur.
9. Do not attempt to x this product in the eld.
WARNING!
THIS IS NOT A CUSTOMIZABLE FIXTURE.
DO NOT MODIFY.
DRY LOCATION
120V
AC
SAFETY & WARNINGS
Input
120VAC, 60Hz
Power
See Specication Sheet
Max Run 300W
Environment Indoor / Dry Location
QUICK SPECS / MODELS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CCT SELECT
2700K 3000K 3500K 4000K 5000K
2 OF 4 IG041822-1.0
SABER™ Under Cabinet Light
INSTALLATION GUIDE
SABER™ Under Cabinet Light INSTALLATION GUIDE
Align Fixture to surface and mount with captive
screws.
MOUNT FIXTURE
FASTEN FIXTURE TO SURFACE
2
Measure and mark surface, then remove captive
screw covers.
Replace captive screw cover.
2.2
TURN POWER OFF AT CIRCUIT
BREAKER
SHOCK HAZARD! May result in serious
injury or death.
Turn power OFF at circuit breaker prior to
installation.
1
3
CONNECT FIXTURES TOGETHER
LINKABLE END-TO-END CONNECTOR
INSTALLATION
2.1
2.3
3 OF 4 IG041822-1.0
SABER™ Under Cabinet Light
INSTALLATION GUIDE
SABER™ Under Cabinet Light INSTALLATION GUIDE
CONNECT TO POWER (DIRECT HARD WIRE)
a
INSTALLATION (CONT.)
4
4
4
Using Phillips head screwdriver, fasten top to
junction box.
Open xture cover by placing athead screwdriver under
lip then twisting.
Open cover to gain access to wiring.
120VAC, 60Hz
CONNECT TO POWER (PLUG-IN CONNECTOR)
Connect power cable with AC plug into 120VAC
receptacle.
b
CONNECT TO POWER (HARD WIRE
CONNECTOR)
Insert connection wires into junction box, then
using twist-on wire connection, connect wiring
within Junction Box.
c
®Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | info@DiodeLED.com
© 2022 Elemental LED, Inc. All rights reserved. Specicaons are subject to change without noce.
IG041822-1.0
4 OF 4
SABER™ Under Cabinet Light
INSTALLATION GUIDE
SABER™ Under Cabinet Light INSTALLATION GUIDE
Lights are
ickering
• Verify strip is connected to a 120VAC, 60Hz
circuit.
Lights will not
illuminate
• Ensure main power is turned On.
• Check wiring to ensure proper polarity.
TROUBLESHOOTING
5
TURN POWER ON AT CIRCUIT BREAKER
Remove knockout from back of xture using hammer and
athead screwdriver.
Connect wiring by inserting corresponding wires into
terminal blocks
Fasten Strain Relief to back of xture.
INSTALLATION (CONT.)
GROUND (GREEN)
HOT (BLACK)
NEUTRAL (WHITE)
GROUND (YELLOW)
HOT (BLACK)
NEUTRAL (WHITE)
Close cover.
/