2. KLUS
  3. FI-8-PRET-ZMZ
FI-8-PRET-ZMZ

KLUS FI-8-PRET-ZMZ User manual

  • Hello! I've reviewed the mounting instructions for the FI-8-PRET-ZMZ series fastener, specifically the silver model. This document details the step-by-step process for assembling and mounting the lighting fixture, including wiring, LED strip placement, and fastener usage. I'm ready to answer your questions about its features and installation.
  • What voltage power supply should be used with the LED tapes?
    What should I avoid doing after tightening the pressure screw?
    When should I not tighten the pressure screw?
*The full range of accessories and electronics is available at www.KlusDesign.eu
www.KlusDesign.eu
NOTE! All LED tapes must be connected to a 12 V or 24 V power supply.
IMPORTANT: Not all possible mounting procedures are presented here.
More mounting procedures and related accessories can be found at www.KlusDesign.eu.
Drawings of extrusions and accessories in these instructions are simplied and only
approximate the actual shapes.
1
FI-8-PRET-ZMZ Fastener – mounting instructions
1.1 Prole
1.2 End cap
1.3 LED strip
1.4 Cover
2.1 Threaded mount lock
2.2 O-ring
2.3 Connector wire
2.4 Fastener body
2.5 Pressure screw
2.6 Spare connector wire
3. Rod*
4. Ceiling fastener*
5. Power supply (12 V / 24 V)*
Lighting xture
FI-8-PRET-ZMZ silver (ref. 42348)rass (ref. 42286CU)
1.1
1.2
1.3
2.3
2.4
2.5
2.1
2.2
3.
4.
5.
FI-8-PRET-ZMZ
1.2
1.4
2.6
www.KlusDesign.eu 2
FI-8-PRET-ZMZ Fastener – mounting instructions
Drill wire holes (2.1) in the prole (1.1).
Drill the holes right next to the
prole wall so as not to damage the
upper edges of the channel on the
prole’s back (gures a, b).
Adhere the LED tape (1.3) in the prole
so as not to cover the holes (gures c, d).
Run the connector wires through the
holes and slide the fasteners into the
channel on the back of the prole. Move
them as close as possible to the holes
and lock them by tightening the heads
(2.4, gures e, f).
c. Bottom view d. Bottom view
e. Top view f. Top view
I
II
III
1.3
1.1
2.1
ø 2,5 mm / 0.1’’
ø 2,5 mm / 0.1’’
2.4
a. b.
_
+
www.KlusDesign.eu 3
FI-8-PRET-ZMZ Fastener – mounting instructions
g. Bottom view h. Bottom view
Cut the wires to a length that
is convenient for you and solder
to the LED tapes (gures g, h).
Mount the end caps (1.2) and the cover
(1.4).
Insert the rods (3) into the holes in the
heads of the fasteners. Lock them by
tightening the pressure screws (2.5) with
an Allen key.
NOTE! After tightening the pressure
screw (2.5), do not turn the head!
This will damage the conductor (2.3).
If the conductor is damaged, go to the
REPLACEMENT OF A DAMAGED
CONNECTOR WIRE below.
IV
V
VI
1.4
1.2
1.2
2.5
2.5
2.3
3.
3.
2.5
+
_
www.KlusDesign.eu 4
FI-8-PRET-ZMZ Fastener – mounting instructions
REPLACEMENT OF A DAMAGED CONNECTOR WIRE
Suspend the lighting xture from the
ceiling fasteners (4), connected to the
power supply (12 V / 24 V) (5).
Unscrew the pressure screw (2.5) and
the threaded mount lock (2.1), remove
the o-ring (2.2) and the damaged
connector wire (2.3) from the head (2.4).
Place a spare conductor (2.6) in the head
and reassemble the fastener.
NOTE! Do not tighten the pressure
screw (2.5) before re-locking the fastener
with the cable in the prole.
Otherwise you will damage the spare
conductor.
VII
4.
4.
5.
2.1
2.2
2.3
2.4
2.5
2.6
2.5
/