Philex 28074R Installation guide

Brand: Philex

Model: 28074R

Type: Installation guide

75MM

75MM 75MM

100MM

100MM 100MM

COMPATIBILITY CHECKER

VESA 50

Fittings

VESA 75

Fittings

VESA 100

Fittings

VESA 200 x 100 Fittings

This TV bracket is designed to t LCD TV’s and computer monitors with VESA 50, VESA 75, VESA

100, VESA 200x100 and VESA 200 bracket ttings. These standard ttings are found on almost all

systems typically up to 32” diagonal screen size although some may vary - in which case you may

need to contact the TV manufacturer for assistance.

The weight capacity of this bracket is 20kg in order for the tilting mechanism to maintain secure.

To check if your TV or monitor is compliant, look at the back of your system and check it has four

equally spaced mounting holes spaced in any of the combinations shown.

TILT & SWIVEL ARM LCD TV MOUNT

Part No. 28074R

Installation Instructions

WARNING!!!!

Correct assembly is essential

This mount should be tted to a solid wood, brick or concrete wall

Note: We have not supplied wall xings with this product. All walls differ in strength and

thickness. We advise that you consult professional personell for guidance for purchasing

screws designed specically for your type of wall.

turn over for installation instructions...

VESA 200

Fittings

Customer Careline: 0901 293 0038

Calls are charged at £1 per minute from a BT landline. Call charges from other networks may vary

Support: http://technical.philex.com

STEP ONE

WALL FITTING FOR WOOD STRUCTURE (eg STUD WALLING)

Due to the width of wooden beams within dividing walls, there is a limitation for the distance between wall mounting

screws. This LCD wall mount has central wall mounting holes for this purpose. Fit three suitable wall screws to your wall

(please seek professional advise before obtaining and tting wall screws - all walls differ!), Fit the screws in the mounting

holes as shown below (along the middle of the bracket).

STEP TWO - ASSEMBLING THE TV MOUNTING SECTION

Fit the TV mounting plate to the tillting clamp as shown below. The knob should not be fully tightened until the installation

has been completed and the tilting angle of the television has been nalised.

WALL FITTING FOR CONCRETE/BRICK WALLS

Fit three suitable wall screws to your wall (please seek professional advise before obtaining and tting wall screws - all

walls differ!), Fit the screws in the mounting holes shown below

BRICK/CONCRETE WALLING

STUD WALLING

Note: wall xings not supplied

Customer Careline: 0901 293 0038

Calls are charged at £1 per minute from a BT landline. Call charges from other networks may vary

Support: http://technical.philex.com

STEP FOUR

- FITTING THE TV MOUNTING PLATE

TO THE BRACKET ARM

Fit the TV mounting plate to the bracket arm as shown

below. Tighten the nut to secure the position. Finally t

the dome caps to the screw head and nut to nish the

installation. Position the TV in the tilting angle required

and tighten the nut holding the TV mounting plate the tilt-

ing clamp.

STEP THREE- FITTING THE TV MOUNTING PLATE

Once you have checked the compatibility of your

television, locate the tting holes on the mounting plate

that match your televisions mounting holes.

Check which type of the supplied tting screws t your

television (M4 or M5 - supplied) and attach the plate

rmly to the back of your television.

STEP FIVE - CABLE MANAGEMENT

This LCD wall mount is supplied with a plastic outer casing. This outer casing allows you to route and hide your power

and other cables along the arm of the mount. Before you t the outer casing, run your cables along the arm and secure

to the arm using tape. Use a knife or scizzors or cut out routing holes in the plastic to allow the cables to pass through.

There are sections of plastic which have been made thinner to allow for easy cutting

Note: TV not shown on mount for illustration purposes

Philex 28074R Installation guide

Philex 28074R Installation guide

Philex 28074R Installation guide

Related papers

Other documents