Philex 28071R Installation guide

Philex
Brand
Philex
Model
28071R
Type
Installation guide

Philex 28071R is a flat-to-wall LCD TV mount compatible with LCD TVs and computer monitors with VESA 50, VESA 75, VESA 100, VESA 200x100, and VESA 200 bracket fittings. It is designed to be mounted on solid wood, brick, or concrete walls.

The mount has two close wall mounting holes for use with wood structures, such as stud walls. It also allows for three suitable wall screws to be fitted to the wall, leaving a 2-3mm gap between the screw head and the wall surface. This allows the plate to slide onto the screws and be tightened for a secure fit.

Philex 28071R is a flat-to-wall LCD TV mount compatible with LCD TVs and computer monitors with VESA 50, VESA 75, VESA 100, VESA 200x100, and VESA 200 bracket fittings. It is designed to be mounted on solid wood, brick, or concrete walls.

The mount has two close wall mounting holes for use with wood structures, such as stud walls. It also allows for three suitable wall screws to be fitted to the wall, leaving a 2-3mm gap between the screw head and the wall surface. This allows the plate to slide onto the screws and be tightened for a secure fit.

75MM
75MM
75MM 75MM
100MM
100MM
100MM 100MM
COMPATIBILITY CHECKER
VESA 50
Fittings
VESA 75
Fittings
VESA 100
Fittings
VESA 200 x 100 Fittings
This TV bracket is designed to t LCD TV’s and computer monitors with VESA 50, VESA 75, VESA
100, VESA 200x100 and VESA 200 bracket ttings. These standard ttings are found on almost all
systems although some may vary - in which case you may need to contact the TV manufacturer
for assistance.
To check if your TV or monitor is compliant, look at the back of your system and check it has four
equally spaced mounting holes spaced in any of the combinations shown.
FLAT-TO-WALL LCD TV MOUNT
Part No. 28071R
Installation Instructions
WARNING!!!!
Correct assembly is essential
This mount should betted to a solid wood, briick or concrete wall
Note: We have not supplied wall xings with this product. All walls differ in strength and
thickness. We advise that you consult professional personell for guidance for purchasing
screws designed specically for your type of wall.
turn over for installation instructions...
VESA 200
Fittings
Customer Careline: 0901 293 0038
Calls are charged at £1 per minute from a BT landline. Call charges from other networks may vary
Support: http://technical.philex.com
STEP ONE
WALL FITTING FOR WOOD STRUCTURE (eg STUD WALLING)
Due to the width of wooden beams within dividing walls, there is a limitation for the distance between wall mounting
screws. This LCD wall mount has two close wall mounting holes for this purpose. Fit three suitable wall screws to your
wall (please seek professional advise before obtaining and tting wall screws - all walls differ!), leaving 2-3mm gap be-
tween the screw head and the wall surface. This allows the plate to slide onto the screws as shown below.
Once the bracket has been tted you can tighten the wall screws to provide a secure t.
WALL FITTING FOR CONCRETE/BRICK WALLS
Fit three suitable wall screws to your wall (please seek professional advise before obtaining and tting wall screws - all
walls differ!), leaving 2-3mm gap between the screw head and the wall surface. This allows the plate to slide onto the
screws as shown below.
Once the bracket has been tted you can tighten the wall screws to provide a secure t.
Customer Careline: 0901 293 0038
Calls are charged at £1 per minute from a BT landline. Call charges from other networks may vary
Support: http://technical.philex.com
STEP TWO
- ASSEMBLING THE MOUNT HEAD
Fit the
v2
  • Page 1 1
  • Page 2 2
  • Page 3 3

Philex 28071R Installation guide

Philex
Brand
Philex
Model
28071R
Type
Installation guide

Philex 28071R is a flat-to-wall LCD TV mount compatible with LCD TVs and computer monitors with VESA 50, VESA 75, VESA 100, VESA 200x100, and VESA 200 bracket fittings. It is designed to be mounted on solid wood, brick, or concrete walls.

The mount has two close wall mounting holes for use with wood structures, such as stud walls. It also allows for three suitable wall screws to be fitted to the wall, leaving a 2-3mm gap between the screw head and the wall surface. This allows the plate to slide onto the screws and be tightened for a secure fit.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents