Philex SLx 28050R User manual

Type
User manual
ma x 8 0 0 mm
ma x 8 0 0 mm
28050R
Flat TV Screen Wall Mount 17 - 70” - Flat to Wall
Main Features
USER GUIDE
•TVSizeRange:17-70”
•MaximumWeightCapacity:40kg
•MountFunction:FlattoWall-UltraThin
•WalltoTVDistance:14.5mm
•
CompatiblewithVESASizes:100x100/100x200/200x200
300x200/300x300/400x300/400x400/600x600/
800x800
•
UniversalMountingSize:800x800mmMax.HolePattern
•
We have not supplied wall xings with this product. All walls dier in strength
and thickness. Consult a qualied installer or seek advice from your local
DIY/hardware store on purchasing suitable wall xings to safely mount the
bracket on the type of wall being used.
•
Check the contents list and images below to check there are no missing or
defective parts.
•
Never exceed the Maximum Weight Capacity shown above.
•
Read these instructions carefully before installation. If in any doubt about
safely installing this product, contact a professional installer for assistance.
•
This product was designed to be installed on wooden stud walls or solid
concrete/brick walls. When xing to walls screws/bolts should be xed into
bricks/stone not into mortar courses.
•
Make sure the wall will support the combined load of the
equipment and hardware.
Also check for hidden wiring or plumbing.
•
Make sure that the heads of the screws/bolts you buy as wall fastenings are
the correct size to hold the bracket securely in position.
For larger/heavier TVs we recommend that you ask someone to assist you
with lifting and positioning your TV.
•
This product is suitable for indoor use only.
•
Improper installation or use of this product can result in product failure,
damage or personal injury.
•
This product contains small items that could cause choking if swallowed, so
keep these items away from children and pets.
•
Appropriate safety equipment and proper tools must be used for installation.
Always check manufacturer’s operating and safety instructions before using
tools and other equipment
WARNING
Components
Wall Mount & VESA Compatibility
• VESAisthestandardadoptedbymostTVmanufacturersforwall
bracket mounting.
• Thereare4holesonthebackofeveryatscreenTVandthe
spacebetweentheholesisgovernedbytheVESAstandard.
• VESAcomesinarangeofsizesdependingontheweightandsize
oftheatscreenTV;sizes100x100mm,100x200mmandsoon...are
standard.NotallatscreenTVsarecompliant,contacttheTV
manufacturer for assistance if your TV does not appear to comply with
VESA.
• TocheckifyourTVormonitoriscompliant,lookattherearof
thedisplaythereshouldbe4screw-holesinasquarepatternor
inlargerdisplaysarectangularshape.SeeFig.2opposite,with
VESAmountingpointsshowninwhitecircles.
• Measurethedistancesmarked(2)(horizontal)x(1)(vertical)in
mmtondyourVESAformat.
Fig. 2
Fig. 1
D4 4.5x 10
washer 4pcs
Supporting Spacer 1pc
Before installation check that you have all the components shown here and that
none of them are damaged.
Please Note wall xings are not supplied with this product.
Wall Plate 2pcs
Supporting Spacer 1pc
M5 x 12mm 4pcs
M-A
M4 x 12mm 4pcs M4 x 22mm 4pcs
M-B M-C
M-D
M-E
M-F
M5 x 22mm 4pcs
D8 8.3x 16
washer 4pcs
D5 5.5 x 12
washer 4pcs
D6 6.3 x 16
washer 4pcs
14 x 6 x 10mm
spacer 4pcs
Wire Clamp x 2pc
Cable Tie 1pc
M-M M-N
M-O
M-G M-H M-K M-LM-I M-J
A
B
C D
Spanner 1pc
M6 x 12mm 4pcs M6 x 22mm 4pcs
M8 x 15mm 4pcs M8 x 30mm 4pcs
M-P M-Q
15 x 8 x 15mm
spacer 4pcs
TV Wire Mount 1pc
X
Before attaching the Wire Mount
B
to the TV you must rst use the Wire
Clamp
M-O
toadjustthewirelengthLtooptimumasindicatedinTable1
or2asappropriate(seebelow).UsetheSpanner
M-Q
supplied to tighten
the clamp as shown in Fig. 7 and use the Cable Tie
M-P
to secure any
excess wire. The TV Wire Mount
B
isthenattachedtothetoptwoVESA
mounting
holes and the lower
SupportingSpacers
C
&
D
to the two
lower
VESAmounting
holes as shown in
Fig.7andFig.8a-c
.
Two lengths
of each size mounting bolts are provided for attaching the TV Mounts
totheVESAmounting
holes on
yourTV.Usethelongerlengthandthe
PlasticSpacers
M-M
or
M-N
for TVs with curved or recessed back panels
asshowninFig.8band8c.Ifyouaremountingtoatelevisionwithaat
back you can use a shorter bolt and will not need a plastic spacer, see
Fig. 8a. You should also use the appropriate size washers as shown in
Fig.8a-c.Makesureallfourboltsareproperlytightenedandheldinplace
byatleastthreefullturns.
With the help of another person, hook the the TV Wire Mount
B
with the
TV attached over the top of t
he
DiskWallPlates
A
and make sure the TV is
level.PulldowngentlyontheTVsothatthewireisrmlylodgedovert
he
disk wall plates
A
seeFig.9.UsetheclipononeoftheSupportingSpacers
D
to hold the TV away from the wall while you make your connections,
seeFig.10.Whenyouhavenishedmakingyourconnectionspulltheclip
attothebackoftheTVandlowertheTVgentlybackagainstthewall
seeFig.11.
PLEASE NOTE: For larger/heavier TVs we recommend that you ask
someone to assist you with lifting and positioning your TV.
©PhilexElectronicLtd.2012.V3
STEP 3 - Hanging and securing the TV
Mounting your TV - Overview
OnceyouhavedecidedwheretolocateyourTVandwherethebracket
needstobepositioned,mountingrequiresthe3stepsdescribedbelow.
Step 1: mark and drill xing holes in the wall and attach the Disk Wall
Plates
A
to the wall using suitable screws/bolts. Step 2 attach the TV Wire
Mount
B
andSupportingSpacers
C
&
D
to the back of the TV using the
PlasticSpacers
M-M
or
M-N
if required. Step 3 hang the TV Wire Mount
B
andTVovertheDiskWallPlates
A
, make your connections then tilt the
TVattothewall.
STEP 2 - Attaching the TV Mounts to the TV
STEP 1 - Fixing the Wall Plates to the Wall
Fig. 3
Fig. 4
Fig. 9
FixingtoStudWalls
The disk wall plates
A
are attached to the wall using two
screws/bolts and
washerssuitableforattachingtowood(ifindoubtaskforadviceatyourlocal
DIY/hardware store and remember to make sure that the heads of the screws/
bolts are the correct size to hold the
DiskWallPlates
A
securelyinposition),
seeFig.4.Useastuddetectortomarkthecentrepointsofthetwostudsyou
wishtomountto(thesewillbeapprox.406,450or600mmapart).Tomark
the exact position of the
holes, hold the
disk wall plates
A
to the wall with
the centres aligned over the stud centres, use a spirit level to make sure
the plates are level, and mark the centre of each hole. Drill your rst hole
as marked and x one of the
DiskWallPlates
A
tothewall.Usingaspirit
level and a ruler check that the position you marked for the second hole
isstillcorrect(re-markifnecessary).Drillthesecondholeandattachthe
second
DiskWallPlate
A
to the wall.
FixingtoConcrete/BrickWalls
ThisprocessisthesameasforattachingtowoodseeFig.5&6.Youwill
however need to use suitable screws/bolts/wall plugs for the type of wall
youaremountingonto(ifindoubtaskforadviceatyourlocalDIY/hard-
ware store and remember to make sure that the heads of the screws/bolts
arethecorrectsizetoholdthebracketsecurelyinposition).UseTable2
below to determine the distance X between the centres of the two Wall
Plates
A
theoptimumvalueswilldependontheVESAsize.Whenxing
to walls screws/bolts should be xed into bricks/stone not into mortar
courses and make sure both screws/bolts are properly tightened.
Fig. 6
Fig. 5
VESA(mm) 200x200orless 400x400 600x600 800x800
X(mm) 80-100 180-220 380-420 580-620
L(mm) 400 500 750 900
VESA(mm) 200x200orless 400x400 600x600 800x800
X=406mm N/A L=700mm L=750mm L=880mm
X=450mm N/A L=710mm L=750mm L=880mm
X=600mm N/A N/A L=880mm L=900mm
X
Table 1 - Stud Wall Fixing
Table 2 - Brick Wall Fixing
X:Spacebetweenstudcentres/wallplatesL:Optimumwirelength
X:SpacebetweenwallplatecentresL:Optimumwirelength
For further information or any queries please contact our
Customer Careline: 08457 573 479 (Localrate–UKonly)
Technical Support: www.philex.com/support
Fig. 7
M-Q
M-O
M-A
M-IM-J
M-K M-L
M-AM-A
M-CM-EM-G
M-A
M-IM-J
M-K M-L
M-CM-EM-G
M-IM-J
M-K
M-DM-B
M-F
M-IM-J
M-K
M-DM-B
M-F
M-M
M-M
M-N
M-N
M-H
M-H
M-L
M-L
Fig. 8a
Fig. 8b
Fig. 8c
Fig. 10
Fig. 11
L
For value of L see
Table1andTable2
  • Page 1 1
  • Page 2 2

Philex SLx 28050R User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI