Updating WinPEP From CD:
With Torque Module
P/N 98295107
©1999-2001 Dynojet Research, Inc. All Rights Reserved. 010517SD
R E S E A R C H
Dynojet Research
200 Arden Drive
Belgrade, MT 59714
© 2001 Dynojet Research, Inc.
Copyright
This manual is copyrighted by Dynojet Research, Inc., hereafter referred to as
Dynojet, and all rights are reserved. This manual is furnished under license and
may only be used or copied in accordance with the terms of such license. This
manual is furnished for informational use only, is subject to change without
notice, and should not be construed as a commitment by Dynojet. Dynojet
assumes no responsibility or liability for any error or inaccuracies that may appear
in this manual.
Trademarks
The Dynojet logo is a trademark of Dynojet Research, Inc.
Any trademarks, trade names, service marks, or service names owned or
registered by any other company and used in this guide are the property of their
respective companies.
Updating WinPEP From CD: With Torque Module i
T
ABLE
OF
C
ONTENTS
List of Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Chapter 1 Updating WinPEP From CD: With Torque Module
Updating WinPEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Updating WinPEP From CD: With Torque Module
TABLE OF CONTENTS
ii
Updating WinPEP From CD: With Torque Module iii
L
IST
OF
F
IGURES
Figure 1-1: Interface Screen—Update WinPEP . . . . . . . . . . . . . . . . . . . . . . . .1-2
Figure 1-2: Welcome Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Figure 1-3: Software License Agreement. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Figure 1-4: Select Which Installation of WinPEP to Update . . . . . . . . . . . . . .1-4
Figure 1-5: Select the Type of Dynamometer. . . . . . . . . . . . . . . . . . . . . . . . .1-4
Figure 1-6: Hardware Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5
Figure 1-7: Select Dynamometer Hardware . . . . . . . . . . . . . . . . . . . . . . . . . .1-5
Figure 1-8: Additional Hardware Modules . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
Figure 1-9: Select Components—Copy Manuals . . . . . . . . . . . . . . . . . . . . . .1-7
Figure 1-10: Select Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8
Figure 1-11: Review Selected Components. . . . . . . . . . . . . . . . . . . . . . . . . . .1-8
Figure 1-12: Enter Torque Module Calibration Number . . . . . . . . . . . . . . . .1-9
Figure 1-13: Select Program Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10
Figure 1-14: Setup Complete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10
Updating WinPEP From CD: With Torque Module
LIST OF FIGURES
iv
Updating WinPEP From CD: With Torque Module 1-1
CHAPTER
1
U
PDATING
W
IN
PEP F
ROM
CD:
W
ITH
T
ORQUE
M
ODULE
This document provides instructions for updating WinPEP from CD and contains
torque module information. To ensure safety and accuracy in the procedures, perform
the procedures as they are described.
Document Part Number: 98295107
Last Updated: 05-17-01
TECHNICAL SUPPORT
For assistance, please contact Dynojet Technical Support at 1-800-992-4993, or write
to Dynojet at 2191 Mendenhall Drive, North Las Vegas, NV 89031.
Visit us on the World Wide Web at www.dynojet.com where Dynojet provides state of
the art technical support, on-line shopping, 3D visualizations, and press releases
about our latest product line.
As a Dyno owner or dealer, access jet kit fact sheets, newsletters, and dealer pricing in
@PREFFERED.Dynojet.com with a click of the mouse.
Updating WinPEP From CD: With Torque Module
CHAPTER 1
Updating WinPEP
1-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPDATING WINPEP
The WinPEP update CD contains everything you need to update the WinPEP
application including manuals, hardware, support programs, and WinPEP itself. This
CD also contains Adobe Acrobat Reader which allows you to view the manuals
included on the CD. Use the following instructions as a guide to update WinPEP for
Windows®95/98.
Note: It is strongly recommended that you exit all other Windows programs
before running this setup program.
1 Insert the Dynojet Update CD in your CD driver.
2Click Update WinPEP to begin.
Figure 1-1: Interface Screen—Update WinPEP
UPDATING WINPEP FROM CD: WITH TORQUE MODULE
Updating WinPEP
Updating WinPEP From CD: With Torque Module
1-3
3 Read the WinPEP Welcome screen and click Next to continue.
Figure 1-2: Welcome Screen
4 Carefully read the WinPEP license agreement and click Yes to continue.
To install WinPEP, you must accept this agreement. If you choose No, setup will
close.
Figure 1-3: Software License Agreement
Updating WinPEP From CD: With Torque Module
CHAPTER 1
Updating WinPEP
1-4
5 Select the installation of WinPEP to update and click Next.
Figure 1-4: Select Which Installation of WinPEP to Update
6 Select the type of dynamometer you are updating and click Next.
Figure 1-5: Select the Type of Dynamometer
UPDATING WINPEP FROM CD: WITH TORQUE MODULE
Updating WinPEP
Updating WinPEP From CD: With Torque Module
1-5
7 Select the dynamometer hardware.
• If you have a hardware stack, select Dynoware EX+.
Note: If you have Dynoware EX+, it will already be selected.
• If you do not have a hardware stack, select Internal PC Card.
Figure 1-6: Hardware Stack
7a Click Next to continue.
Note: If you do not have the Dynoware EX+ hardware, skip to step #9.
Figure 1-7: Select Dynamometer Hardware
Updating WinPEP From CD: With Torque Module
CHAPTER 1
Updating WinPEP
1-6
8 Select any additional modules that you purchased for your Dynoware EX+
hardware and click Next to continue.
Figure 1-8: Additional Hardware Modules
UPDATING WINPEP FROM CD: WITH TORQUE MODULE
Updating WinPEP
Updating WinPEP From CD: With Torque Module
1-7
9 Select the manuals to be installed.
Dynojet recommends that you leave the Copy Manuals box checked. This will
install the latest manuals to your hard drive.
The manuals are accessible from the CD at any time.
9a Select Copy Manuals to install the latest manuals.
OR
Click on the Copy Manuals text to choose which manuals you want to
install.
Note: If you are unable to view this manual on your computer screen, select the
Install Acrobat Reader box. Acrobat Reader will allow you to view the Dynojet
Installation and User manuals on your computer screen.
Figure 1-9: Select Components—Copy Manuals
Updating WinPEP From CD: With Torque Module
CHAPTER 1
Updating WinPEP
1-8
10 Select the language you prefer the units to be displayed in and click Next.
Figure 1-10: Select Language
11 Review the selected components and click Next to continue.
OR
Click Back to make additional changes.
Figure 1-11: Review Selected Components
UPDATING WINPEP FROM CD: WITH TORQUE MODULE
Updating WinPEP
Updating WinPEP From CD: With Torque Module
1-9
12 Enter the Torque Module information.
If you selected Torque Module in step #8, you will now be prompted for
additional information. If you did not select Torque Module, skip to step #13.
12a Enter the calibration number stamped on the Torque Module Calibration
Arm. Use the calibration arm with the extension unless you do not have
enough space in your dyno room.
If you will be using the calibration arm without the extension, use the
number stamped on the main bar in the Torque Module Package. If you will
be using the calibration arm with the extension, use the number stamped on
the extension.
Note: Follow the directions on the screen exactly. Failure to perform the
directions accurately will result in improper torque values.
Note: You must re-calibrate your torque module if you change the number listed
above.
12b Click Next to continue.
Figure 1-12: Enter Torque Module Calibration Number
Updating WinPEP From CD: With Torque Module
CHAPTER 1
Updating WinPEP
1-10
At this point, the selected manuals will be copied to the WinPEP directory and Acrobat
Reader, if selected, will automatically install itself.
Setup will automatically add program icons to the Program Folder. You may type a
new folder name or select one from the Existing Folders list.
13 Click Next to continue.
Figure 1-13: Select Program Folder
14 Click Yes if you would like a WinPEP icon placed on the start menu.
15 Click Finish to complete the setup
Figure 1-14: Setup Complete
The update is complete. You may now run the updated program by double-clicking
the program icon. Reading and understanding the Dynojet Installation and User
manuals will assist you in getting the most out of your investment.
/
