©1999-2002 Dynojet Research, Inc. All Rights Reserved. 020118SD
Monitor Arm
Installation Guide
P/N 98225100
Version 2
Dynojet Research, Inc.
2191 Mendenhall Drive
North Las Vegas, NV 89031
200 Arden Drive
Belgrade, MT 59714
999
© 2002 Dynojet Research, Inc.
Copyright
This manual is copyrighted by Dynojet Research, Inc., hereafter referred to as
Dynojet, and all rights are reserved. This manual is furnished under license and
may only be used or copied in accordance with the terms of such license. This
manual is furnished for informational use only, is subject to change without
notice, and should not be construed as a commitment by Dynojet. Dynojet
assumes no responsibility or liability for any error or inaccuracies that may appear
in this manual.
Trademarks
The Dynojet logo is a trademark of Dynojet Research, Inc.
Any trademarks, trade names, service marks, or service names owned or
registered by any other company and used in this guide are the property of their
respective companies.
Monitor Arm Installation Guide
i
T
ABLE
OF
C
ONTENTS
Monitor Arm Installation
Conventions Used In This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing the Monitor Arm Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing the Arms and Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Monitor Arm Installation Guide
TABLE OF CONTENTS
ii
Monitor Arm Installation Guide
1
M
ONITOR
A
RM
I
NSTALLATION
This document provides instructions for installing the monitor arm to the model 250
motorcycle dynamometer (dyno). To ensure safety and accuracy in the procedures,
perform the procedures as they are described.
Document Part Number: 98225100
Version 2
Last Updated: 01-18-02
Monitor Arm Installation Guide
MONITOR ARM
2
CONVENTIONS USED IN THIS MANUAL
The conventions used in this manual are designed to protect both the user and the
equipment.
TECHNICAL SUPPORT
For assistance, please contact Dynojet Technical Support at 1-800-992-4993, or write
to Dynojet at 2191 Mendenhall Drive, North Las Vegas, NV 89031.
Visit us on the World Wide Web at www.dynojet.com where Dynojet provides state of
the art technical support, on-line shopping, 3D visualizations, and press releases
about our latest product line.
PARTS LIST
The following table lists all of the parts included in the Monitor Arm Installation kit.
Check your kit against the parts listed to make sure you have received all of the parts.
If any part is missing, contact Dynojet Technical Support.
example of convention description
The Caution icon indicates a potential hazard to the
dynamometer equipment. Follow all procedures
exactly as they are described and use care when
performing all procedures.
Part Number Description Quantity
21229300 Monitor Arm Tray 1
32391064 Bushing, 1" x 2", 10 Gauge, Stl 3
35521420 Plastic Cap, 1-3/4" x 1/2", Black 4
36701100 Nut, 1/2"-13, Hex 2
36801253 Screw, 1/2"-13 x 1-1/2", Sh-Cap 2
36932100 Washer, 3/8", Splitlock, Stl 1
36942100 Washer, 1/2", Splitlock, Stl 2
36943100 Washer, 1/2", Flat, Stl 4
61329100 Monitor Arm 2
61329102 Monitor Arm Base 1
61329103 Monitor Arm Upright 1
DM150-011-002 Washer, 3/8" Flat 1
DM150-011-006 Bolt, 3/8"-16 x 1 1/4", Hex 1
INSTALLATION GUIDE
Installation
Version 2 Monitor Arm Installation Guide
3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION
This articulated arm and platform supports the monitor, keyboard, and mouse in a
convenient position for operation while seated on the motorcycle. The arm can be
mounted on either side of the dynamometer.
INSTALLING THE MONITOR ARM BRACKET
1 Drill a 1/2-inch hole through the aluminum deck plate as shown in Figure 1. Use
the existing hole under the deck plate as a guide.
2 Fasten the top of the monitor arm bracket to the dyno using a 3/8-inch bolt,
3/8-inch lock washer, and 3/8-inch flat washer.
Note: Do not tighten.
3 Secure the bottom of the bracket to the dyno using two 1/2-inch bolts,
four 1/2-inch washers, two 1/2-inch lock washers, and two 1/2-inch nuts.
4 Fully tighten all three bracket bolts.
Figure 1: Install the Monitor Arm Bracket
monitor arm bracket
drill hole
3/8-inch bolt
1/2-inch bolt
Monitor Arm Installation Guide
MONITOR ARM
Installation
4
INSTALLING THE ARMS AND TRAY
1 Place a bushing on the pin of the first arm and insert the arm into the upright.
Both arms are identical and interchangeable.
2 Place a bushing on the pin of the second arm and insert the arm into the first arm.
3 Place a bushing on the pin of the tray and insert the tray into the second arm.
4 Insert a plastic cap in both ends of each arm.
5 Check for clearance between the monitor arm and motorcycle, walls, ceiling, etc.
Note: Dynojet does not recommend placing the computer CPU on the
monitor/keyboard tray since vibration can cause damage to the computer.
Figure 2: Install the Arms and Tray
tray
second arm
bushing
first arm
bushing
bushing
upright
/
