Dynajet Power Commander III Installation guide

Brand
Dynajet
Model
Power Commander III
Category
Motorcycle Accessories
Type
Installation guide
i520-411 www.powercommander.com 2008 Triumph Speedmaster - PCIII USB - 1
2008 Triumph Speedmaster
Installation Instructions
Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
Parts List
1 Power Commander
1 USB Cable
1 CD-ROM
1 Installation Guide
1 Power Adapter
2 Power Commander Decals
2 Dynojet Decals
2 Velcro
®
Strip
2 O2 eliminators
1 Alcohol Swab
You can also download the Power
Commander software and latest maps
from our web site at:
www.powercommander.com
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Button Adjustment Display
Faceplate Buttons
Expansion Port
USB Port
3 Remove the left side cover (Fig. B).
4 Lay the PCIII under the seat area and
route the harness out the left side of
the bike. Go under the frame follow-
ing the stock wiring harness (Fig. C)
Fig. AFig. BFig. C
i520-411 www.powercommander.com 2008 Triumph Speedmaster - PCIII USB - 2
1 Remove the seat.
2 Remove the cover to the left side of
the airbox intake (Fig. A)
Remove cover
Remove cover
PCIII harness
6 Route the PCIII harness over to the
right side of the bike. Run the har-
ness to the rear of the throttle bodies
(Fig. E)
Fig. D
5 Attach the ground wire of the PCIII
harness to the negative side of the
battery (Fig. D)
i520-411 www.powercommander.com 2008 Triumph Speedmaster - PCIII USB - 3
7 Unplug the 3 pin BLACK connector
on the right side of the frame(Fig. F)
This connector goes to the throttle
bodies.
Fig. E
Fig. F
PCIII ground wire
PCIII harness
PCIII harness
8 Plug the PCIII harness in-line of the
stock wiring harness (Fig. G).
i520-411 www.powercommander.com 2008 Triumph Speedmaster - PCIII USB - 4
Fig. G
Fig. HFig. J
PCIII connectors
Stock connectors
9 Locate the Throttle Position Sensor on
the left side of the throttle bodies.
10 Using the supplied wire tap crimp
onto the GREEN wire with the
YELLOW stripe.
11 Attach the GREY wire from the PCIII
to wire tap (Fig. H).
To hide this connection you can make
a cut in the stock sheathing further up
the harness and then tap onto the wire
Plug the TPS harness back onto the
throttle bodies if it was unplugged.
12 Attach the PCIII to the rear fender
just rear of the frame crossover. Use
the supplied velcro to secure the unit.
Use the supplied alcohol swab to
clean both surfaces before attaching.
13 Reinstall covers and seat.
TPS
Grey wire from PCIII
Wire tap
14 Locate the O2 sensors connections
which are above the oil cooler.
These are BLACK 4 pin connectors.
You can follow the wires from the O2
sensors up to this location.
15 Unplug each of the O2 sensor connec-
tions.
16 Plug the Dynojet O2 eliminators into
the wiring harness.
The O2 sensors will not be connected
to anything at this time. They can be
removed from the exhaust if desired.
Fig. K
i520-411 www.powercommander.com 2008 Triumph Speedmaster - PCIII USB - 5
Unplug
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Dynajet Power Commander III Installation guide

Brand
Dynajet
Model
Power Commander III
Category
Motorcycle Accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents