American Dynamics 1676B Installation Instructions Manual

Brand: American Dynamics

Model: 1676B

Category: Motor vehicle electronics

Type: Installation Instructions Manual

This manual is also suitable for

This manual describes the installation and operating procedures for the American Dynamics 1676B Series Operator Keyboards.

The 1676B Series keyboards are used with the following matrix switching systems: the 1650B MicroPower, the 2050

MegaPower II, the 2150 System V, and the 2350 systems. Two 1676B operator keyboards are available for full function control:

the 1676B for system monitors 1 - 64, and the 1676B2 for system monitors 65 - 128. Executive desktop keyboard versions of

both are available which will only access matrix switching functions.

Installation Instructions

Models 1676B and 1676B2

Operator Keyboard

This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to

be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the

purchaser under a license for use on a single system.

NOTE: Information furnished by SENSORMATIC is believed to be accurate and reliable. However, no responsibility is

assumed by SENSORMATIC for its use; nor for any infringements of other rights of third parties which may result from its use.

No license is granted by implications or otherwise under any patent or patent rights of SENSORMATIC.

The installation of this product should be made by qualified

service personnel and should conform to all local codes.

QA301C

Warning: This product generates, uses, and can

radiate radio frequency energy and if not

installed and used in accordance with the

instructions manual, may cause interference to

radio communications. It has been tested and

found to comply with the limits for a Class A

computing device pursuant to Part 15 of FCC

Rules, which are designed to provide reasonable

protection against such interference when

operated in a commercial environment.

Operation of this product in a residential area is

likely to cause interference in which case the

user at his own expense will be required to take

whatever measures may be required to correct

the interference.

To reduce the risk of fire or shock hazard, do

not expose this product to rain or moisture.

AMERICAN

DYNAMICS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVERS (OR BACK) .

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

RISK OF ELECTRIC SHOCK

DO NOT OPEN

 CAUTION

The lightning flash with arrowhead

symbol, within an equilateral

triangle, is intended to alert the

user to the presence of uninsulated

"dangerous voltage" within the

product's enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and maintenance

(servicing) instructions in the

literature accompanying the product.

Unpack carefully. This is an electronic product and should

be handled as such. Compare the items received with the

packing list with your order.

Be sure to save:

1. The shipping cartons and insert pieces. They are the )

safest material in which to make future shipments of

the product.

2. The IMPORTANT SAFEGUARDS sheet.

3. These Installation and Operating Instructions.

User maintenance of this unit is limited to external cleaning

and inspection. For specific recommendations refer to the

IMPORTANT SAFEGUARDS sheet packaged with this product.

If you require information during installation of this

product or if service seems necessary, contact the

American Dynamics Repair and Service Department at

(800) 442-2225. You must obtain a Return Authorization

Number and shipping instructions before returning any

product for service.

Do not attempt to service this product yourself. Opening or

removing covers may expose you to dangerous voltages or

other hazards. Refer all servicing to qualified personnel.

Table of Contents

General Description.............................................................. 1

Keyboard Connections ......................................................... 2

Junction Box Mounting................................................... 2

Junction Box Connections............................................... 2

Keyboard Setup .................................................................... 4

Quantity of Monitors....................................................... 4

Base Monitor Number..................................................... 5

Keyboard Operation ............................................................. 6

RUN Mode ...................................................................... 6

HOLD Mode.................................................................... 6

CALL............................................................................... 6

Pan/Tilt, Lens, and Auxiliary .......................................... 7

Appendix - Typical System Connections

1676 to 1650................................................................... A

1676 to 1996 ................................................................... B

1676 to 2150/2350.......................................................... C

1676 to 1981 Port Expander........................................... D

GENERAL DESCRIPTION

The 1676 Series keyboards are used for full function control

with the following matrix switching systems: the 1650B

MicroPower, the 2050 MegaPower II, the 2150 System V, and

the 2350 System. Two 1676 operator keyboard models are

available: the 1676B for controlling system monitors 1 - 64,

and the 1676B2 for controlling system monitors 65 - 128.

1676 Series keyboards, when used with suitable accessory

equipment, allows camera call up, sequence programming, and

remote camera control. As a security feature, the 1676 cannot

access and change the system parameters of date/time, camera

titles, or preset scenes.

The 1676 keyboard controls 1, 2, 3, or 5 monitors of a pre-

selected group, allowing local partitioning of the system

monitors. Monitor access is accomplished by pressing the

MON button. This will advance the keyboard access to the

next monitor in the group. (See Keyboard Operation, page 6.)

The 1676 Operator keyboard uses reverse notation for the

entry of numeric camera number commands. The numbers

entered into the keyboard are not displayed. Cameras are

called to a monitor by selecting a camera number on the entry

pad then pressing the CAM button.

DESCRIPTION

Figure 1 - 1676 Keyboard Control Panel

MON - Depending on the internal

setup, selects 1,2, 3 or 5 monitors

Joystick - Controls up, down,

left, right Camera Pan/Tilt

PROG - Used to enter a

"scratch pad" sequence/tour

Used for Tour Programming:

NEXT - Next camera in sequence

RUN - Runs sequence

HOLD - Stops sequence

SHOT - Used to call a

pre-programmed (Preset) Shot

Controls LENS functions

for cameras

Numeric Entry Keys

ALARM Programming:

ON - Activates CAM for alarm contact

OFF - Turns off for alarm contact

ACK - Acknowledges an alarmed CAM

CAM - Used to

select a camera

AUX ON/OFF - Used to turn

ON/OFF Auxiliaries

LED

display

- ENTER -

PROG

- SWITCHER -

- ALARM -

- MONITOR -

- LENS -

ZOOM

FOCUS

IRIS

AUX

OFF

ACK

OFF

OPEN

NEAR

FAR

WIDE

TELE

MON

SHOT

CAM

HOLD

RUN

KEYBOARD CONNECTIONS

The 1676 keyboard is supplied with a wall-mount transformer

(7.5 VAC), part number TP8059, a seven-foot 8-pin modular

cable, part number JJ0007, and an 8-pin modular junction box,

part number HP0047. The 8-pin modular format is commonly

referred to as a RJ-45.

Junction Box Mounting

The HP0047 Junction Box (Figure 2) interfaces with three

separate components: the 1676 keyboard, the wall-mount

transformer, and a Matrix Switching System (i.e., 1650B, 1996

CPU, 2150, 2350).

The junction box is connected to the 1676 keyboard with the

supplied modular cable. The wall-mount transformer is

connected to the junction box with a 2-wire cable. The

junction box must be located within reach of both the modular

cable and the cable from the wall-mount transformer. The

junction box is connected to a Matrix Switching System with

either another junction box (supplied with that switching

system) or via a 1981 Port Expander, using 9-pin connectors.

DO NOT INSERT THE WALL TRANSFORMER INTO

THE POWER SOURCE UNTIL ALL CONNECTIONS

HAVE BEEN VERIFIED.

Junction Box Connections

To connect the junction box to the keyboard, plug the modular

cable into the 8-pin modular jack both in the junction box and

on the bottom of the keyboard (Figure 3, page 3).

To connect the junction box to the wall transformer, refer to

illustrations in the Appendix and to Table 1 below.

Definition Designation Pin Color

Transformer In AC 1 Blue

Ground GND 2 Orange

No Connection NC 3 Black

Receive Data RCD 4 Red

Transmit Data XMIT 5 Green

No Connection NC 6 Yellow

Ground GND 7 Brown

Transformer In AC 8 Gray

Table 1 - Junction Box Terminal Definition

KEYBOARD CONNECTIONS

Pin 1

Pin 2

Pin 3

Pin 7

Pin 8

Pin 6

Figure 2 - Junction Box

To connect the 1676 keyboard to a particular switching system,

refer to the following steps and the illustrations contained in

the Appendices.

a) For 1650B Systems see Appendix A.

b) For 1996 CPU (2050 Systems) see Appendix B.

c) For 2150/2350 Systems see Appendix C.

d) For multiple keyboards using the 1981 Port Expander see

Appendix D.

1. Wire the pendant cable from the wall plug transformer to

the AC input connectors 1 and 8 on the Junction Box .

2. Plug the transformer into the power source, 120 VAC

standard or 230 VAC for X models.

3. Verify 7.5 VAC between terminals 1 and 8.

4. After verification, remove the transformer and continue the

connections.

5. Connect a 3-wire RS-232 type cable to pins 4 (RCD), 5

(XMIT), and 7 (GND) on the junction box.

For RS-232 connections, connect the Transmit (XMIT) of

the keyboard junction box to the Receive (RCD) of the unit

and the Receive (RCD) of the keyboard junction box to the

Transmit (XMIT) of the Video Switching System.

DO NOT CONNECT THE CABLE SHIELD AT THE

JUNCTION BOX.

Note: Modem "control" lines, CTS and DTR, are not used.

Some Modems require that these lines be tied together.

6. Plug the transformer into the power source. Press the MON

button several times until the monitor number appears on

the LED display. This operation initializes the keyboard.

KEYBOARD CONNECTIONS

KEYBOARD SETUP

The 1676 keyboard is designed to control a maximum of five

contiguous monitors. The number of monitors controlled by

the keyboard is set using a DIP switch located on the under

side of the unit (see Figure 3, below). By selecting the

appropriate combination (shown in Table 4), the keyboard can

control either 1, 2, 3, or 5 monitors.

This DIP switch also determines the starting number (base

number) for the specified group of monitors. Table 5 on page

5 lists the DIP switch settings for the desired base number.

The keyboard LED shows the relative monitor number within

the group which is currently defined for the keyboard. The

number will appear as a 1, 2, 3, 4, or 5, depending on which

monitor is selected.

For Example: An operator wants to manage five monitors,

starting with monitor number 27.

The DIP switch is set to the group code for five monitors,

and to the base monitor number 27.

The operator now can access monitors 27, 28, 29, 30, and

31. If monitor number 31 is selected, then the number 5

will be displayed in the keyboard LED.

To set up a keyboard for monitor control, turn the keyboard

over and remove the plastic plug. This provides access to the

programming DIP switch (see Figure 3, below).

As delivered, the 1676B model is set to control one monitor in

the first group of monitors (1 through 5) which is monitor

number 1. The 1676B2 model is set to control one monitor in

the first group of monitors (65 through 69) which is monitor

number 65.

Quantity of Monitors Selection

To select the quantity of monitors to be controlled by the

keyboard use Table 4, below. This set up uses S7 and S8 of

the DIP switch. The location of S7 and S8 are shown in Figure

3, below.

Quantity S7 S8

100

210

301

511

0 = off; 1 = on

Table 4 - S7 and S8 Configuration Select

KEYBOARD SETUP

8-position DIP Switch

8-pin Modular Plug

Figure 3 - DIP Switch Location

Base Monitor Number Selection

The selection of the starting monitor for the group uses S1, S2, S3, S4, S5, and S6 of the DIP switch. The monitor number is

selected on the DIP switches by calculating the monitor number in binary, minus 1. This allows the keyboard to be programmed

for access to different groups of monitors. As delivered, all the switches are in the down, or off, position, corresponding to

monitor 1. The monitor numbers are listed for each of the two keyboard models, 1676B and 1676B2.

1676B 1676B2 DIP SWITCH 1676B 1676B2 DIP SWITCH

MONITOR NUMBER 6 5 4 3 2 1 MONITOR NUMBER 6 5 4 3 2 1

01 65 0 0 0 0 0 0 33 97 1 0 0 0 0 0

02 66 0 0 0 0 0 1 34 98 1 0 0 0 0 1

03 67 0 0 0 0 1 0 35 99 1 0 0 0 1 0

04 68 0 0 0 0 1 1 36 100 1 0 0 0 1 1

05 69 0 0 0 1 0 0 37 101 1 0 0 1 0 0

06 70 0 0 0 1 0 1 38 102 1 0 0 1 0 1

07 71 0 0 0 1 1 0 39 103 1 0 0 1 1 0

08 72 0 0 0 1 1 1 40 104 1 0 0 1 1 1

09 73 0 0 1 0 0 0 41 105 1 0 1 0 0 0

10 74 0 0 1 0 0 1 42 106 1 0 1 0 0 1

11 75 0 0 1 0 1 0 43 107 1 0 1 0 1 0

12 76 0 0 1 0 1 1 44 108 1 0 1 0 1 1

13 77 0 0 1 1 0 0 45 109 1 0 1 1 0 0

14 78 0 0 1 1 0 1 46 110 1 0 1 1 0 1

15 79 0 0 1 1 1 0 47 111 1 0 1 1 1 0

16 80 0 0 1 1 1 1 48 112 1 0 1 1 1 1

17 81 0 1 0 0 0 0 49 113 1 1 0 0 0 0

18 82 0 1 0 0 0 1 50 114 1 1 0 0 0 1

19 83 0 1 0 0 1 0 51 115 1 1 0 0 1 0

20 84 0 1 0 0 1 1 52 116 1 1 0 0 1 1

21 85 0 1 0 1 0 0 53 117 1 1 0 1 0 0

22 86 0 1 0 1 0 1 54 118 1 1 0 1 0 1

23 87 0 1 0 1 1 0 55 119 1 1 0 1 1 0

24 88 0 1 0 1 1 1 56 120 1 1 0 1 1 1

25 89 0 1 1 0 0 0 57 121 1 1 1 0 0 0

26 90 0 1 1 0 0 1 58 122 1 1 1 0 0 1

27 91 0 1 1 0 1 0 59 123 1 1 1 0 1 0

28 92 0 1 1 0 1 1 60 124 1 1 1 0 1 1

29 93 0 1 1 1 0 0 61 125 1 1 1 1 0 0

30 94 0 1 1 1 0 1 62 126 1 1 1 1 0 1

31 95 0 1 1 1 1 0 63 127 1 1 1 1 1 0

32 96 0 1 1 1 1 1 64 128 1 1 1 1 1 1

0 = off; 1 = on

Table 5 - S1-6 Monitor Number Selection Switch Settings

KEYBOARD SETUP

KEYBOARD OPERATION

Keyboard control of system functions is "monitor oriented" in

that a keyboard controls only those system functions associated

with the display on the monitor to which it is "connected".

System monitors not under keyboard control continue to

operate in whatever state they were left.

As a security feature, 1676 keyboards cannot alter the system

settings of date and time, camera title, and camera preset.

The number of the monitor within the specified group (1-5) to

which keyboard is currently connected is shown in the

keyboard LED display, MONITOR. See Figure 1 (pg. 1).

The programming functions of the 1676 keyboards are

restricted to those monitors under control of the 1676

keyboard. These programming features are:

● Arming cameras and monitors for alarm inputs.

● Disarming cameras/monitors for alarm inputs.

● Programming sequences for monitors. This is limited to

"Scratch Pad Tours".

On startup, the LED display will be blank.

1. Press the MON button to cause the display to turn on and

remain on after the keyboard is powered up.

System functions are accessed from a keyboard by first placing

one of the monitors of the system under the control of the

keyboard ("Calling" a monitor to a keyboard) and then

"Calling" cameras in the system to that monitor.

A monitor is "connected to" or placed under the control of the

1676 keyboard by "selecting" the monitor from the group of

monitors specified by the switch settings.

To "SELECT" a monitor:

1. Press the MON button. The keyboard will select the next

monitor in the group.

The NUMBER OF THE MONITOR (within the group)

NOW UNDER CONTROL will appear in the MON

display.

The monitor will be displaying either a sequence of

camera scenes (RUN mode) or a single camera scene

(HOLD or CALL mode).

The monitor screen will incorporate the system on-screen

display shown in Figure 4.

If the system includes an Alarm Interface, this interface will

override operator control of an armed monitor. The on-screen

display will indicate when such an override has occurred.

RUN Mode

The RUN mode is established, from the HOLD or CALL

mode, by depressing the RUN button. The monitor will then,

depending on the system setup, either continuously display a

sequence of camera scenes or display a sequence of camera

scenes and hold on a selected scene. For information on how

to program a Sequence/Tour, refer to the appropriate

Switching System Manual.

HOLD Mode

The HOLD mode is established, from the RUN mode or by

depressing the HOLD button when the monitor is displaying

the desired camera scene. The monitor continues to display

this camera scene until another instruction is received.

CALL

A specific camera may be called to the monitor from either the

RUN or the HOLD mode.

To "Call" a camera to the monitor under control:

1. Enter the number of the desired camera.

2. Press the CAM (Camera) button on the keyboard.

The monitor will continue to display this camera scene until

another instruction is received.

KEYBOARD OPERATION

8 Characters

per line

004 UPSTAIRS 07-18 - 87

02 ENTRANCE 15: 22: 06

Figure 4 - On-Screen Dwell Time Display

Pan/Tilt, Lens, and Auxiliary Control

When called on-screen, cameras at sites equipped with 1680

and/or 1640 Series Receivers are controlled as follows:

Pan and Tilt - Hold the joystick in the direction you wish to

move the camera. The camera will continue to move until the

joystick is centered.

Iris, Focus, and Zoom - Push and hold the function button

designating the desired action. The function will continue to

change as long as the button is depressed. Release the button

when the desired effect has been obtained.

Auxiliaries - Momentary or Latching action of auxiliaries

depends on the options installed on the 1680 Series Receiver at

the site being controlled.

1. Enter the auxiliary number

2. Press the AUX ON Button to activate the auxiliary.

3. Release the AUX ON button:

If auxiliary action stops the auxiliary is momentary.

If auxiliary action continues the auxiliary action is latching.

4. Press the AUX OFF button to deactivate a latching

auxiliary.

Note: The current state of latching functions such as locks or

gates is not indicated on the keyboard. If critical, operator

feedback should be provided via the monitor or some other

device.

KEYBOARD OPERATION

APPENDIX

TYPICAL SYSTEM CONNECTIONS

1676 TO 1650

NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD.

EACH RS232 PORT IS PROGRAMMABLE.

1650A/1650B

MONITOR

RS-232

OUT

RED

GREEN

BROWN

THREE CONDUCTOR SHIELDED

BELDEN 8770 OR EQUIVALENT

TP8059

7.5 VOLTS AC

1.5 AMP

HP0047

JJ0007

HP0047

1676

JJ0007

NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD.

EACH RS232 PORT IS PROGRAMMABLE.

1996

TYPICAL SYSTEM CONNECTIONS

1676 TO 1996

RED

GREEN

BROWN

THREE CONDUCTOR SHIELDED

BELDEN 8770 OR EQUIVALENT

TP8059

7.5 VOLTS AC

1.5 AMP

HP0047

JJ0007

HP0047

1676

JJ0007

12 3456789

PROG MONDATA LINE PORTS

120V

60HZ

NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD.

EACH RS232 PORT IS PROGRAMMABLE.

2150/2350

TYPICAL SYSTEM CONNECTIONS

1676 TO 2150/2350

RS232 PORTS

MONITORS

ALARMS

RELAY

KEYBOARDS

2468101214161820222426283032

135791113151719212325272931

CAMERAS

-CODE-

RED

GREEN

BROWN

THREE CONDUCTOR SHIELDED

BELDEN 8770 OR EQUIVALENT

TP8059

7.5 VOLTS AC

1.5 AMP

HP0047

JJ0007

HP0047

1676

JJ0007

TYPICAL SYSTEM CONNECTIONS

1676 TO 1981 Port Expander

1996

12 3456789

PROG MONDATA LINE PORTS

120V

60HZ

CPU

KBD

12 345

67 89

12345

67 89

12 345

67 89

1981

HP0047

JJ0007

3-wire, shielded Belden 8770,

or equivalent

1676

HP0047

An American Dynamics Product

Designed and built by

Sensormatic CCTV Systems Division

One Blue Hill Plaza

Pearl River, New York, 10965

(914) 624-7600

Technical Support Center 1-800-442-2225

FAX: 914-624-7685

8000-0884-01 OP1676BC

June 1996 Printed in USA

Specifications

SIZE: 3.0"H x 5.5"D x 10.8"W

WEIGHT: 1.7 Lbs. (0.8 kg)

VOLTAGE INPUT: 1676B/1676B2 - 7.5V A.C. Wall Transformer 120V/60Hz Nominal

1676BX/1676B2X - 7.5V A.C. Wall Transformer 230V/50Hz Nominal

POWER CONSUMPTION: 4.5W Nominal

American Dynamics 1676B Installation Instructions Manual

Brand: American Dynamics

Model: 1676B

Category: Motor vehicle electronics

Type: Installation Instructions Manual

This manual is also suitable for

Download PDF

report

American Dynamics 1676B Installation Instructions Manual

This manual is also suitable for

American Dynamics 1676B Installation Instructions Manual

Related papers

Other documents