KALATEL DSR-1000eZ User manual

K

a

l

a

t

e

l

D

S

R

-

1

0

e

Z

Single Channel Color Digital Video Recorder

User Manual

Kalatel DSR-1000eZ ii 0150-0238B

WARNING!

To prevent fire and electric shock, do not expose this product to rain or moisture.

The lightning flash with the arrowhead symbol,

within an equilateral triangle, is intended to alert

the user to the presence of uninsulated

"dangerous voltage" within the products enclosure

that maybe of sufficient magnitude to constitute a

risk of electric shock to persons.

!

The exclamation point, within an equilateral

triangle, is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

CAUTION!

To prevent electric shock, do not remove cover.

No user serviceable components are inside.

Refer servicing to qualified service personnel.

!

CAUTION! Lithium Battery

Danger of explosion if battery is

incorrectly replaced. Replace only

with the same or equivalent type

recommended by the

manufacturer.

ATTENTION

This product contains a recyclable lithium battery.

It may be illegal to dispose of this battery

improperly under local, state, or federal laws.

Check with your local waste management officials

for disposal and recycling options.

CAUTION!

Electrostatic-Sensitive Device!

Use proper CMOS and MOSFET handing precautions, including approved

grounded wrists straps, etc., to avoid damage to this unit or its internal

components, from electric discharge.

WARNING!

This equipment generates, uses and can radiate radio frequency energy, and if not installed and used

in accordance with the instructions in this manual, may cause interference to radio communications. It

has been tested and found to comply with the limits for a Class A computing device pursuant to subpart

J of part 15 of FCC rules which are designed to provide reasonable protection against such

interference when operated in a commercial environment. This equipment has also been tested and

found to comply with the requirements for a CE Class A device and TUV safety standards.

Operation of this equipment in a residential area may cause interference, in which case the user is

required to take all measures that are necessary, at the user's expense, to correct the interference.

0150-0238B iii Kalatel DSR-1000eZ

IMPORTANT INFORMATION

Software and/or firmware is furnished to the purchaser under a license for use on a single system.

Software and/or firmware included with this equipment are the sole proprietary property of, confidential to,

and copyrighted by GE Interlogix, Corvallis, Oregon, USA. The software/firmware are not to be copied or

disclosed in any manner without the express written consent of GE Interlogix.

All information and specifications furnished by GE Interlogix are believed to be accurate and reliable. No

responsibility is assumed by GE Interlogix for neither its use nor any infringements of rights of third parties

that may result from its use. No license is granted by implication or otherwise under any patent or patent

rights of GE Interlogix.

The Kalatel™ brand name and product model numbers are the property of GE Interlogix.

COPYRIGHT, 2004: The contents of this manual may not be copied or reproduced in any manner or

form without the prior written consent of GE Interlogix.

Kalatel DSR-1000eZ iv 0150-0238B

0150-0238B v Kalatel DSR-1000eZ

CONTENTS

1 FEATURES, CONNECTIONS, AND SETUP ................................................... 1-1

1.1 Product Description.........................................................................................1-1

1.2 Features............................................................................................................1-1

1.3 Unpacking ........................................................................................................1-1

1.4 Installation Environment.................................................................................1-2

1.5 Passwords........................................................................................................1-2

1.6 Front Panel Controls .......................................................................................1-3

1.7 Back Panel Connections.................................................................................1-4

1.8 Accessories I/O Port........................................................................................1-6

1.9 Setting the Time and Date...............................................................................1-8

1.10 Setting the Alarms .........................................................................................1-10

2 USER OPERATIONS................................................................................. 2-1

2.1 Recording.........................................................................................................2-1

2.2 Playback...........................................................................................................2-2

2.3 The Search Interface........................................................................................2-4

2.4 Specifying Search Parameters .......................................................................2-4

3 THE MENU SYSTEM................................................................................. 3-1

4 OPERATOR PROGRAMMING...................................................................... 4-1

4.1 Main Menu → Time/Date..................................................................................4-1

4.2 Main Menu → Alarms.......................................................................................4-4

4.3 Main Menu → Timer Settings..........................................................................4-5

4.4 Main Menu → Record Settings .......................................................................4-6

4.5 Main Menu → Display Settings.......................................................................4-8

4.6 Main Menu → Archive Setup.........................................................................4-10

4.7 Main Menu → Advanced Menu .....................................................................4-15

5 INSTALLER PROGRAMMING...................................................................... 5-1

5.1 Advanced Menu → Disk Overwrite Mode ......................................................5-1

5.2 Advanced Menu → Disk Maintenance............................................................5-2

5.3 Advanced Menu →Audio Record Setting ......................................................5-3

5.4 Advanced Menu → Auto Delete Mode............................................................5-4

5.5 Advanced Menu → Communications.............................................................5-4

5.6 Advanced Menu → Multiplexer Format..........................................................5-7

5.7 Advanced Menu → Adjust Picture..................................................................5-7

5.8 Advanced Menu → Front Panel Lock.............................................................5-8

5.9 Advanced Menu → Factory Settings..............................................................5-8

5.10 Advanced Menu → Change Password...........................................................5-9

Kalatel DSR-1000eZ vi 0150-0238B

5.11 Advanced Menu → Languages.......................................................................5-9

5.12 Advanced Menu → Firmware Upgrade ..........................................................5-9

6 WAVEBROWSER..................................................................................... 6-1

6.1 WaveBrowser Overview and Controls...........................................................6-2

6.2 DSR WaveLink .................................................................................................6-4

6.2.1 Functionality......................................................................................................................6-4

6.3 Upgrading the DSR with WaveBrowser.........................................................6-5

7 RS-232 REMOTE PROTOCOL.................................................................. 7-1

8 FACTORY DEFAULTS............................................................................... 8-1

9 TECHNICAL SPECIFICATIONS ................................................................... 9-1

10 WARRANTY AND SERVICE ..................................................................... 10-1

10.1 Factory Service..............................................................................................10-1

10.2 Warranty and Return Information.................................................................10-2

0150-0238B 1-1 Kalatel DSR-1000eZ

1 FEATURES, CONNECTIONS, AND SETUP

1.1 Product Description

The DSR-1000eZ is a Digital Video Recorder designed to be a direct replacement for a Time Lapse

VCR. Digital Video Recording allows the user to have continuous recording on a hard disk, without

the need for replacing or rewinding of videotapes. The DSR-1000eZ provides menu based search

capabilities for recorded events, as well as access to live or recorded data via the Ethernet (optional).

1.2 Features

• Single channel Composite Video Input / Output connection.

• Accepts Single Camera input or a Multiplexed input from most popular multiplexers.

• Compatible with Color or Monochrome cameras.

• Records up to 60 pictures per second (NTSC) or 50 pictures per second (PAL).

• Continuous Recording in Disk Overwrite mode.

• Video Archiving via the unit's SCSI port.

• Access to Live or Recorded video via the Ethernet (Ethernet option only).

• Continues Recording while Archiving, or transmitting data via the Ethernet (Ethernet option

only).

• A simple on-screen menu system.

• Includes WaveReader software for viewing Live or Recorded images on a PC (Ethernet option

only).

• Timed recording.

• Audio Recording (Audio option only).

• Programmable Auto Delete Mode.

• Auto-Daylight savings time change function.

• Clock synchronization with Network Server.

• Integrated WaveBrowser Software.

• Dynamic IP addressing (DHCP).

1.3 Unpacking

Check the package and contents for visible damage. If any components are missing or damaged,

contact the supplier immediately. Do not attempt to use the unit. If, for any reason they must be

returned, the contents must be shipped in the original packaging.

Package Contents

• The DSR-1000eZ unit.

• Accessories PCB.

• The DSR-1000eZ user manual.

Kalatel DSR-1000eZ 1-2 0150-0238B

• WaveReader software with User Manual (Ethernet option only).

• Archiving Addendum.

1.4 Installation Environment

Power: Ensure that the site's AC power is stable and within the rated voltage of the external power

supply. If the site's AC power is likely to have spikes or power dips, use power line conditioning or an

Uninterruptable Power Supply (UPS).

Ventilation: Install the unit in a well-ventilated area. Take note of the locations of the cooling vents in

the unit's enclosure, and ensure that they are not obstructed.

Temperature: Observe the unit's ambient temperature specifications when choosing a location

space. Extremes of heat or cold beyond the specified operating temperature limits may cause the unit

to fail. Do not install the unit on top of other hot equipment.

Moisture: Do not expose the unit to rain or moisture. Moisture can damage the internal components.

Do not install this unit near sources of water.

Chassis: You can place other equipment on top of the unit if it weighs less than 35 pounds.

1.5 Passwords

Figure 1-1 Passwords

Password Name Function Changeable by user? Password

Advanced Menu

Password

Provides access to the

Advances menu for the

installer.

Yes: See page 5-9

3 4 7 7

Factory Password

Restores the unit to the

factory defaults.

No

8 1 1 1

A password is provided to limit access to the Advanced menu. It is recommended that the default

password be changed after installation is complete. As a security measure, store the password in the

administrator's secured files or in a limited access area. For instructions on entering the Advanced

menu with the password see section 4.7 Main Menu → Advanced Menu on page 4-15.

A password is also provided to return the unit to the factory defaults. For instructions on returning the

unit to the factory defaults, see section 5.8 Advanced Menu → Factory Settings on page 5-8.

0150-0238B 1-3 Kalatel DSR-1000eZ

1.6 Front Panel Controls

Figure 1-2 Front Panel

1 2 4 5 63

7

8

9

10

1. Record button: Press this button to begin recording.

2. Reverse play button: Press this button to playback video in reverse at the normal record speed.

3. Stop button: Press this button to stop Recording or Playback.

4. Play Forward button: Press this button to playback video at the normal record speed.

5. Pause button: Press this button to pause playback.

6. Search button: Press this button to enter the Search Filters menu.

7. Increase and Decrease Record Speed buttons: Press these buttons to increase or decrease

the Record or Playback speed.

8. Combination Menu and Enter button: Press the lower half of the button (the Menu button) to

enter the Menu system. Also used to move to higher level menus while in the menu system.

--OR—

Press the upper half of the button (the Enter button) to make or confirm a selection in the menu

system.

9. Power On Indicator and Alarm Indicator: Indicates power and an alarm indication when their

respective LED’s are lit.

10. Jog / Shuttle: The Jog (the inner of the two dials) is used for single frame advance while in

Pause mode; it is also used to change the value of a parameter while in the menu system. The

Shuttle (the outer of the two dials) is used to Fast Forward and Rewind while in the Play mode.

Kalatel DSR-1000eZ 1-4 0150-0238B

1.7 Back Panel Connections

Figure 1-3 Back Panel

6

1

2

4

5

3

7

1. I/O Port: For connecting peripheral devices such as alarm devices, alarm relays, or the VEXT

connection.

2. RS-232 Serial Port: Serial port for Flash Upgrading of software. Also for external control of

unit.

3. Ethernet Port (Optional): For viewing Live or Recorded images on a PC via the Ethernet.

4. Power Connector: Connect 12 Volt DC external power supply.

5. SCSI Port: For connecting an SCSI compatible archive device.

6. Audio In (Optional): RCA jack, 315mV, 40k Ohms. Unbalanced.

Audio Out (Optional): RCA jack, 315mV, 600 Ohms. Unbalanced.

7. Video In: Composite video input with BNC style connector.

Video Out: Composite video output with BNC style connector.

Ethernet Port (Ethernet models only)

Wire Type: CAT5

Connector Type: RJ-45

Max Cable Length: 100 feet / 30.5 meters

Minimum Cable Length: 6 feet / 1.8 meters

Hub Wiring Configuration: Straight Through

PC Wiring Configuration: Cross Over

The cable connection configuration depends on your

network configuration:

• For a DSR-1000eZ that connects directly to a

Hub, use a Straight Through connection.

• For a DSR-1000eZ that connects directly to a

PC, use a Cross-over connection.

Consult with your MIS personnel for the specific type

of configuration. See section 5.5 Advanced Menu →

Communications for information about configuring

the ethernet settings in the menu system.

0150-0238B 1-5 Kalatel DSR-1000eZ

RJ-45 Pin Configuration for Ethernet Port

Pin Use

1 TX+ 5 Not Connected

2 TX- 6 RX-

3 RX+ 7 Not Connected

4 Not Connected 8 Not Connected

82 3 4 5 6 71

RJ-45 Connector on

Back Panel

Power Connector

Power Supply Input

Power Supply Output

Voltage: 120 to 240 Volt AC

Tolerance: ±10%

Frequency: 50 to 60 Hz

Voltage: 12 Volt DC

Power: 35 Watt

Connector: 2.1mm barrel, Center

Positive

SCSI Port

Connector: 50 Pin, High Density SCSI-2.

Gender (on unit): Female

Compatible devices: DAT, AIT, CD-R, CD-RW

Autoloader Support?: No

SCSI ID: 0

The unit is equipped with a SCSI port for

connecting external archive devices. The unit only

supports a single SCSI device. The SCSI ID must

be set to 0.

The SCSI bus must be terminated, otherwise the

system will not operate properly.

Additional menu setup may be necessary to

configure archive device. See section 4.6 Main

Menu → Archive Setup.

RS-232 Serial Port

Use a Null Modem cable when connecting to a

PC. When connecting to a multiplexer, it may

be necessary to construct a cable using the pin-

out documentation of the MUX as a guide. See

the pin-out configuration for the DSR-1000eZ

below.

Connector Type: DB-9

Gender (on unit): Male

Cable Required (Connected to PC): Null Modem

Cable Required (Connected to Multiplexer):

Variable, depending on pin-out configuration of

MUX.

Kalatel DSR-1000eZ 1-6 0150-0238B

DB-9 Pin Configuration for Serial Port

Pin Use

1 DCD 4 Not Connected 7 RTS

2 RX 5 Ground 8 CTS

3 TX 6 Not Connected 9 Not Connected

1

5

6

9

DB-9 Connector on

Back Panel

Video Input and Output

The unit is equipped with a Composite video input

and output. The video input is auto terminating.

Composite Input: 75 Ohm BNC connector.

Composite Output: 75 Ohm BNC connector.

Composite Looping: Yes, while unit is On or Off.

1.8 Accessories I/O Port

ACCESSORIES

1 5

6 9

The back panel of the unit is equipped with an Accessories Port (DB-9

style connector). Connect the Accessories PCB (supplied with the unit) to

the Accessories Port. Wire all accessories to the Accessories PCB.

Do not attempt to wire accessories directly to the DB-9 connector.

If the Accessories PCB is lost or missing, contact GE Interlogix Customer

Service for a replacement (Part Number 0900-0127a). As a substitute,

purchase a female DB-9 connector and make all connections as shown in

this section.

DB-9 Connector on

Back Panel

Pin 1: Alarm In.

Pin 2: Alarm Out.

Pin 3: Record Start In.

Pin 4: Alarm Record Reset.

Pin 5: VEXT Pulse Out.

Pin 6: Error Out.

Pin 7: Ground.

Pin 8: Videoloss Out.

Pin 9: Disk End Out.

Pin 10: Ground.

1

2

3

4

5

6

7

8

9

GND

Accessories PCB

Alarm In

An alarm condition can be activated by an Active Low TTL input

or by relay contact devices such as pressure pads, passive

infrareds, door switches, or other similar devices.

Input: Active Low TTL w/ pull-ups

or Normally Open Relay.

High: 5V (12V tolerant)

Low: Ground

Minimum Duration: 0.5 Seconds

0150-0238B 1-7 Kalatel DSR-1000eZ

Figure 1-4 Normally Open Relay Alarm Connection

Pin 1

Pin 7 or 10

Alarm Input

Ground

Accessories PCB

Typical Alarm Device

Refer to each alarm devices's

manual for specific wiring details.

Normally Open

(Closes During Alarm)

Alarm Out

The Alarm output is activated when a teletext alarm is detected,

or while the Alarm Input is active. The Alarm output is only

active for the duration of the alarm event.

Output: Active Low

High: 12V

Low: Ground

Current Out: 50mA Max

Short Circuit Protected.

Low for duration of alarm.

Record Start In

Record Start In will place the unit in Record mode when

activated. Compatible with the Disk End Out signal from a

second unit.

Input: Active Low TTL w/ pull-ups

or Normally Open Relay.

High: 5V (12V tolerant)

Low: Ground

Minimum Duration: 0.5 Seconds

Alarm Record Reset

This feature is for future development, and has not yet been implemented.

VEXT Pulse Out

Output: Active Low

High: 5V

Low: Ground (0.8V Max)

Current Out: 50mA Max

Short Circuit Protected.

The Video External Pulse connection (VEXT) simplifies

multiplexer operation by automatically synchronizing the

Multiplexer and the DSR-1000eZ.

The DSR-1000eZ sends a VEXT pulse to the Multiplexer

indicating that it is ready to record the next image. The

Multiplexer responds by sending the next image to the Video

Input on the DSR-1000eZ.

The VEXT connection is especially beneficial for units

configured with dual record speeds (Normal and Alarm).

Use of the VEXT connection is Highly Recommended when

connecting the unit to a multiplexer.

Kalatel DSR-1000eZ 1-8 0150-0238B

Error Out

The Error Out signal is activated when the unit experiences any

operational or internal error.

Output: Open Collector

High: Transistor Off

Low: Transistor On

Active When On.

Current Out: 10mA Max

Minimum Duration: 0.5 Seconds

Videoloss Out

The Videoloss Out signal is activated when the unit experiences

videoloss on the selected video input (Composite or SVHS).

In the event of videoloss, VIDEOLOSS will be indicated near the

upper left hand corner of the primary monitor.

Output: Open Collector

High: Transistor Off

Low: Transistor On

Active When On.

Current Out: 10mA Max

Minimum Duration: 0.5 Seconds

Disk End Out

The Disk End Out is activated when there is 5 minutes of

recording space left on the hard disk. It will also be activated if a

DAT or AIT tape archiving device is connected, and the tape

end is encountered. The DSR-1000eZ must be in Record mode,

with Background Archiving ON, and set to Continuous Overwrite

mode.

Output: Open Collector

High: Transistor Off

Low: Transistor On

Active When On.

Current Out: 10mA Max

Minimum Duration: 0.5 Seconds

1.9 Setting the Time and Date

It is recommended that, as a minimum, the following menu items be configured before using the unit.

For detailed information about using the menu system, see section 3.

o Main Menu → Time/Date → Set Time Format

Time Format Setup

Select Format

12 Hour

To set the Time format, use the Jog to select the desired Time format.

Format the time as either:

• 12 HOUR

• 24 HOUR

Press the Enter button to confirm the selection and exit the menu.

--OR—

Press the Menu button to exit the menu without making changes.

0150-0238B 1-9 Kalatel DSR-1000eZ

o Main Menu → Time/Date → Set Date Format

Date Format Setup

Select Format

MM/DD/YY

To set the Date format, use the Jog to select the desired Date format.

Format the Date as either:

• DD/MM/YY

• MM/DD/YY

• YY/MM/DD

Press the Enter button to confirm the selection and exit the menu.

--OR—

Press the Menu button to exit the menu without making changes.

o Main Menu → Time/Date → Set Time

Time Setup

HH MM SS

03 05 53

[CANCEL] [OK]

To set the Time:

1. With HH MM SS highlighted, press the Enter button. The

highlighting will move to the row of numbers.

2. Enter the time in Hours, Minutes, and Seconds. Use the Jog to

change the values. Use the Shuttle to navigate among the

three fields.

3. Press the Enter button to confirm the selection.

4. To Save the changes and Exit the menu: Use the Jog to

select [OK], then press the Enter button.

--OR--

5. To Exit the menu without making changes: Use the Jog to

select [CANCEL], then press the Enter button.

o Main Menu → Time/Date → Set Date

Date Setup

MM DD YY DAY

12 17 00 SUN

[CANCEL] [OK]

To set the Date:

1. With MM DD YY DAY highlighted, press the Enter button. The

highlighting will move to the row of numbers.

2. Enter the date in Months, Days, Years. Day of the Week will

update automatically. Use the Jog to change the values. Use

the Shuttle to navigate among the three fields.

3. Press the Enter button to confirm the selection.

4. To Save the changes and Exit the menu: Use the Jog to

select [OK], then press the Enter button.

--OR--

5. To Exit the menu without making changes: Use the Jog to

select [CANCEL], then press the Enter button.

Kalatel DSR-1000eZ 1-10 0150-0238B

1.10 Setting the Alarms

o Main Menu → Alarms

Alarm Settings

Hardwire Alarm : Enable

Teletext Alarm : Disable

Alarm Buzzer : Enable

[CANCEL] [OK]

Use this menu to specify:

• Whether an alarm condition will be activated when the

unit detects a signal on the Alarm In connection.

• Whether a teletext alarm signal (generated by a

multiplexer or other device) will cause the unit to

activate an alarm condition.

• Whether the internal buzzer is activated during an

alarm condition.

Alarm Settings

Hardwire Alarm : Enable

Teletext Alarm : Disable

Alarm Buzzer : Enable

[CANCEL] [OK]

To configure the alarm settings:

1. Use the Shuttle to navigate among the fields.

2. Use the Jog to change the values of the highlighted

fields.

3. To Save the changes and Exit the menu: Use the

Jog to select [OK], then press the Enter button.

--OR--

4. To Exit the menu without making changes: Use the

Jog to select [CANCEL], then press the Enter button.

0150-0238B 2-1 Kalatel DSR-1000eZ

2 USER OPERATIONS

2.1 Recording

RECORD

To begin recording, press the Record button. RECORD will be indicated for

three seconds, near the upper left hand corner of the primary monitor. The

unit always starts recording at the end of the previously recorded data.

Recording will continue until:

• Another mode is selected (Play mode, Reverse Play,or Stop

mode).

• The disk is full (In No Overwrite and Overwrite Once modes).

See section 5.1 Advanced Menu → Disk Overwrite Mode on

page 5-1, for details regarding Disk Overwrite modes.

Record button

Normal Recording

SPEED

REC/PLAY

The unit records at the normal record speed until an alarm condition is detected.

The normal record speed is indicated on the monitor if the display option is enabled,

and can be altered using the Up/Down Record Speed buttons, or in the menu

system.

For information about altering the normal record speed from the menu system, see

Main Menu → Record Settings → Normal Record Speed, on page 4-7 of the

Operator Programming section of this manual.

The normal record speed can be altered while the unit is recording. The unit will

continue recording while the menu system is active.

Record Speed

buttons

Alarm Recording

ALARM

When an alarm condition is detected, the unit automatically switches to the

alarm record speed. The alarm condition is indicated in several ways:

• With the word ALARM, displayed on the primary monitor, near the

upper left hand corner of the screen.

• With the internal buzzer (if activated in the menu system). For

information about activating the internal buzzer during alarms, see

Main Menu → Alarms on page 4-3 of the Operator programming

section of this manual.

• By an external device, connected to the alarm output of the unit (if

the unit is installed that way).

Alarm Indicator

The alarm record speed cannot be changed using the Up/Down Record Speed buttons on the front

panel. The alarm record speed must be changed in the menu system. For information about altering

the alarm record speed, see Main Menu → Record Settings → Alarm Record Speed, on page 4-7

of the Operator Programming section of this manual.

The unit returns to the normal record speed when the alarm condition ends.

Kalatel DSR-1000eZ 2-2 0150-0238B

Disk Nearly Full Notification

Message

Disk Full. Recording Has Stopped.

[OK]

This message will appear on the primary monitor to

indicate that the unit has stopped recording, because

the disk is full.

In No Overwrite mode: The user must acknowledge

the on-screen message by pressing the Enter button.

Unit will not record over previously recorded data. To continue recording, the data must be erased (or

deleted) in the Advanced → Disk Maintenance menu.

In Overwrite Once mode: The user must acknowledge the on-screen message by pressing the Enter

button.

The unit will continue recording again when the user presses the Record button.

2.2 Playback

Play Forward

PLAY

To begin normal playback, press the Play Forward button. The unit will begin

playing back data from the beginning of the last recording session.

Playback is indicated:

• As PLAY near the upper left hand corner of the primary monitor, for

three seconds.

Play Forward

button

Reverse Play

REVERSE PLAY

To begin reverse playback, press the Reverse play button. The unit will begin

playing back data from the beginning of the last recording session.

Reverse playback is indicated:

• As REVERSE PLAY near the upper left hand corner of the primary

monitor, for three seconds.

If there is only one recording session on the hard disk, the unit will indicate START

OF DATA on the primary monitor.

Reverse play

button

Playback Speed

SPEED

REC/PLAY

The unit will playback the data at the rate it was recorded. The user can alter the

playback speed using the Up/Down Record Speed buttons.

Altering the playback speed overrides any change in playback speed that would

occur due to an alarm condition in the playback. To clear the override, press the

Stop button, then press the Play button to resume playback at the speed the data

was recorded.

Record Speed

buttons

0150-0238B 2-3 Kalatel DSR-1000eZ

Fast Forward

REW FF

During playback, rotate the Shuttle clockwise to view the data at a Higher than

normal rate. Increasing the amount of rotation increases the rate of playback.

Fast Forward is indicated:

• As FAST FORWARD near the upper left hand corner of the primary

monitor, for three seconds.

Jog / Shuttle

Rewind

REW FF

During playback, rotate the Shuttle counter-clockwise to view the data (in

reverse) at a Higher than normal rate. Increasing the amount of rotation increases

the rate of playback.

Rewind is indicated:

• As REWIND near the upper left hand corner of the primary monitor, for

three seconds.

Jog / Shuttle

Pause

PAUSE

During playback, press the Pause button to pause playback, and display a single

frame on-screen.

Pause is indicated:

• As PAUSE near the upper left hand corner of the primary monitor, for

three seconds.

Pause button

Single Frame Advance & Single Frame Rewind

REW FF

During Pause mode, rotate the Jog dial to view the frame directly before or after

the frame displayed on-screen.

Jog / Shuttle

AutoPause

During playback, moving the Jog (the inner dial) in any direction will freeze

playback. Depress the Freeze or any Play button to continue playback.

Start of Data & End of Data

If the start or end of data is reached during playback, START OF DATA or END OF DATA is indicated

near the upper left hand corner of the primary monitor.

Kalatel DSR-1000eZ 2-4 0150-0238B

2.3 The Search Interface

SEARCH

The Search Interface feature allows the user to search the hard disk for recorded

events, such as an alarm condition, or a previous recording session. For example,

each time Record mode is activated, it is considered a separate recording

session.

To enter the Search Filters menu, press the Search button. The Search Filters

menu is displayed on the primary monitor.

Search button

Search Filters

Start

DATE: 12/25/00 [ ]

(MM/DD/YY)

Stop

01/01/01 [ ]

(MM/DD/YY)

Start

TIME: 11:11:21 [ ]

Stop

12:34:34 [ ]

1 2 3 4 5 6 7 8

CAMERA: [ ][ ][ ][ ][ ][ ][ ][ ]

ALARM: [ ]

Use this to specify:

• The Start and Stop date of

the search.

• The Start and Stop time of

the search.

• Which cameras to search

exclusively.

• To search for recorded

alarms.

[CANCEL] [START SEARCH]

Searching for All Recorded Events

Using the Shuttle to navigate, highlight [START SEARCH], then press the Enter button. The Search

Results window will appear. For information about selecting a recorded event, see Selecting from

the Search Results, in this section.

2.4 Specifying Search Parameters

Selecting a Start and Stop Date

1. Using the Shuttle to navigate, highlight the DATE parameter, then press the Enter button. The

unit will enter Edit mode.

2. Use the Jog to change the start and stop date values. Use the Shuttle to navigate among the

different parameters.

3. To activate the start or stop date parameter, use the Jog to place an [X] in the check box.

4. Press the Enter button at any time to exit Edit mode.

Selecting a Start and Stop Time

1. Using the Shuttle to navigate, highlight the TIME parameter, then press the Enter button. The

unit will enter Edit mode.

2. Use the Jog to change the start and stop time values. Use the Shuttle to navigate among the

different parameters.

3. To activate the start or stop time parameter, use the Jog to place an [X] in the check box.

Page is loading ...

KALATEL DSR-1000eZ User manual

Other documents