MOUNTUP MU8003 User manual

Brand
MOUNTUP
Model
MU8003
Category
Flat panel desk mounts
Type
User manual
Premium Triple Monitor Stand
Instruction Manual
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
75x75mm
100x100mm
(1~14kg)x3
(2.2~30.9lbs)x3
MA01N-36P-US2.0
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
01
(1~14kg)x3
(2.2~30.9lbs)x3
K (x1)
Wingnut
H (x1)
Carriage Bolt
D (x3)
VESA Plate
F (x1)
Clamp
L (x3)
Bolt M6x10mm
N (x5)
Bolt M6x10mm
C (x1)
Base
E (x1)
Bracket
J (x1)
Grommet Base
O (x3)
Bolt M6x18mm
B (x1)
Pole
G (x1)
Support Cover
P (x4)
Pad
A (x1)
Arm
Q (x1)
Middle Head
If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper
installation (including not properly following the indicated instructions or cautions /attentions), such as using the
product for monitors over its load capacity or for any purpose not explicitly specied, may cause damage or serious
injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF
CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
I (x1)
Support Plate
M (x1)
Wire clip
R(x1)
4mm Allen Key
S(x1)
5mm Allen Key
T(x1)
6mm Allen Key
M-C (x12)
Spacer H10mm
M-A (x12)
M4x12mm
M-B (x12)
M4x25mm
Mount Bracket (E) to Base (C) with Bolts (N). Bolts could be tightened by the 4mm Allen Key (R).
Apply pads (P) to the bottom of Base (C) to avoid desk scratches.
ASSEMBLY STEPS
STEP 1 : Clamp Installation OR Grommet Base Installation
02
Firstly mount Bace (C) to Pole (B) using Bolts (O). Tighten them using 4mm Allen Key (R).
Attach Clamp (F) to Bracket (E) with Bolts (N) and 4mm Allen Key (R). Adjust the Clamp width to t with desk.
P
R
O
B
C
RNRN
FF
M
R
E
10-55mm
0.39-2.2”
OR
50-85mm
1.97-3.35”
OPTION A: Clamp Installation
G
OPTION B: Grommet Base Installation
Place Carriage Bolt (H) through the center of Grommet Base (J).
Mount Grommet Base to Base (C) bottom with Bolts (N) and tighten them by 4mm Allen Key (R).
Apply pads (P) to the bottom of Base (C) to avoid desk scratches.
STEP 1 : (Continued)
03
P
J
H
N
R
K
I
Run Carriage Bolt (H) through grommet hole on desktop. Attach Support Plate (I) and Wingnut (K).
At last, tighten Wingnut (K).
Secure stand to desktop by tightening Clamp (F) or by Allen key (T).
Attach Base Support Cover (E) to Bracket (E).
T
OR
F
C
10-80mm
0.39-3.15"
Ø10-80mm
Ø0.39-3.15”
Install the middle head (Q) wire clip(M) and swivel arm (A) to the pole (B).
Fasten the bolt with supplied 6mm Allen key (T)
STEP 2 : Arm Installation
04
T
A
Q
M
DESK DESK
WARNING:
For your safety, do not move the stand o your desk!
B
05
STEP 3 : Attach Monitor
OPTION A: Flat Back Monitor
OPTION B: Curved / Recessed Back Monitor
Do not tighten the screws excessively
or your monitor might be damaged.
Do not tighten the screws excessively
or your monitor might be damaged.
monitor monitormonitor
No!
Monitor Monitor Monitor
No!
D
M-A
T
D
M-B
M-C
T
Attach the VESA plate (F) to the back of monitor and
secure it by using a 6 mm Allen Key (Q) to tighten
screws (M-A ) .
Attach the VESA plate (F) to the back of monitor and
secure it by using a 6 mm Allen Key (Q) to tighten
screws (M-B) along with spacers (M-C).
STEP 4 : Hang Monitor
06
Slide the monitors onto the head of swivel arm. Install the security bolt (L). Make sure the security bolt is
tightened before you rotate the monitor.
Guideline to adjust monitor tilting angle.
L
Important Notice:
The pressure of the gas spring is initially set at the lowest value.
So when the monitor is hung on, make sure you hold it with
both hands and DO NOT let it go down suddenly.
S
Problem:
If monitor faces down
Solution:
1. Loosen the tilting bolt.
2. Hold the bottom of monitor
with one hand and adjust to
determine your desired tilt
angle.
3. Retighten the tilting bolt
towards " " to x the angle.
T
STEP 5 : Adjust Gas Spring Tension
07
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counterclockwise(“+”direction) to increase gas
spring tension until the arm can stay as intended.
Situation 2: Arm rises up/can't be pressed down
Upper Arm with monitor rises up automatically or can't be pressed
down and fails to stay where intended.
Solution:
Turn the inside screw clockwise(“-”direction) to decrease gas spring
tension until the arm can stay as intended.
For intended functioning of the mount, you will need to adjust the tension of Arm (A) in accordance with your
monitor weight by 6mm Allen Key (T).
Monitor Weight
Circles (AT LEAST)
2.2 lbs
(1 kg)
5 7 10 13 16 20min
8.8 lbs
(4 kg) 15.4 lbs
(7 kg) 22 lbs
(10 kg) 28.7 lbs
(13 kg)
6.6 lbs
(3 kg) 30.9 lbs
(14 kg)
For how many circles the screw should be turned, please refer to the table below.
Note2:
T
A
CAUTION
Note1:
Be sure to keep the arm in horizontal position during adjustment.
Or else it would be dicult to adjust the mount or damage the mount.
STEP 6 : Cable Management
08
1
1
2
Press
Press
Press
Press
Slide
1
1
2
Press
Press
Press
Press
Run cables from monitor through bottom of arm. Reattach plastic covers as shown in diagram.
Remove Cable Cover
Attach Cable Cover
Remove bottom plastic covers from arm as shown in diagram.
Do not need to take much eort to pull the ends of the cable cover away from the arm.
Slide
Adjust monitor position and rotation.
Store Allen keys (R, S) in wire clip (G) for future use.
Adjust as Desired
09
Tilt
Swivel
Rotation
Height
Height
+90°
-45°
180°
270°
Swivel
Swivel
360°
Tilt
Swivel
360°
Rotation
360°
Swivel
S
R
Note: To ensure stability, the tightness of the rotating axis has been
preseted, so it would be kind of dicult to rotate the VESA plate.
Suggestion: Please attach the monitor rst, then hold the two
sides of it with both hands, and rotate vigorously. If that doesn't
work out, please do not hesitate to ask for our help.
10
Product Dimensions
75mm/2.9"
100mm/3.9"
114mm/4.5"
75mm/2.9"
100mm/3.9"
114mm/4.5"
270° 360°
360°
180°
360°
10-85mm
0.39-3.35”
10-80mm
0.39-3.15”
+90°
-45°
100mm
3.9”
440mm
17.32”
200mm
7.9”
44mm
1.7”
200mm
7.9”
225-315mm
8.9-12.4”
60mm
2.4”
155mm~510mm
6.1”~20.1”
1458mm~1638mm
57.4”~64.5”
CAUTION AND MAINTENANCE:
• Don't allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals
(at least every three months).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

MOUNTUP MU8003 User manual

Brand
MOUNTUP
Model
MU8003
Category
Flat panel desk mounts
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents