V I V O STAND-V101Q User manual

Brand: V I V O

Model: STAND-V101Q

Category: Flat panel desk mounts

Type: User manual

Pneumatic Arm Single Ultrawide

Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v101q

SKU: STAND-V101Q

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

A (x1)

Upper Arm

B (x1)

Lower Arm

C (x1)

VESA Plate

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

D (x1)

Base

E (x1)

Upper Clamp

F (x1)

Lower Clamp

G (x1)

Cable Clamp Clip

H (x1)

Grommet Plate

I (x1)

Support Plate

J (x1)

Knob

K (x4)

Pad

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualied technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

S-B (x5)

M6x10mm Flathead

Screw

S-C (x1)

M6x12mm

Thumbscrew

M-A (x4)

M4x12mm Screw

M-B (x4)

M4x16mm Screw

S-A (x1)

Carriage Bolt

M-D (x4)

M6x16mm Screw

M-E (x4)

M6 Washer

M-F (x4)

Spacer

T-A (x1)

3mm Allen Wrench

T-B (x1)

4mm Allen Wrench

T-C (x1)

6mm Allen Wrench

M-C (x4)

M6x12mm Screw

ASSEMBLY STEPS

2.2-30.9lbs

(1-14kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

STEP 1 (Option A)

Clamp Installation

Secure Upper Clamp (E) to the underside of Base (D) using M6x10mm Flathead Screws (S-B) and 4mm

Allen Wrench (T-B). Remove adhesive backing and apply Pads (K) to the underside of Base (D).

Connect Lower Clamp (F) to the front of Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm

Allen Wrench (T-B). For desktops 10-55mm (3/8” to 2 1/4”) thick, use top holes on Upper Clamp. For

desktops 50-85mm (2” to 3 3/8”) thick, use the bottom two holes.

Secure clamp assembly to desktop by tightening the hand bolt. Aix Cable Clamp Clip (G) to the

back of clamp assembly.

Proceed to Step 2 on page 5.

S-B

T-B

10-55mm

50-85mm

T-B

S-B

STEP 1 (Option B)

Grommet Installation

Insert Carriage Bolt (S-A) into Grommet Plate (H) and secure to underside of Base (D) using M6x10mm

Flathead Screws (S-B) and 4mm Allen Wrench (T-B).

Peel back adhesive backing and apply Pads (K) to underside of Base (D).

S-A

S-B

T-B

Place base assembly over grommet hole in desktop and place Support Plate (I) and Knob

(J) on the end of Carriage Bolt (S-A). Tighten Knob (J) to secure.

S-A

STEP 2

Place Lower Arm (B) onto Base (D) and secure by tightening set screw with 3mm Allen Wrench

(T-A). Install Upper Arm (A) on Lower Arm (B) and tighten set screw with 3mm Allen Wrench (T-A) to

secure.

STEP 3

T-A

BT-A

Secure VESA Plates (C) to back of monitors using appropriate Screws (M-A thru M-D), M6 Washers

(M-E), and 6mm Allen Wrench (T-C). Use Spacers (M-F) for curved monitor.

Flat Back Monitors

Curved Monitors

M-A

M-C

M-B

M-D

M-E

M-F

- OR -

STEP 4

Place monitor with VESA Plate (C) onto Upper Arm (A) and secure with M6x12mm Thumbscrew (S-C).

STEP 5

While holding Upper Arm (A) in the horizontal position, adjust the gas spring tension using 6mm Allen

Wrench (T-C).

S-C

CAUTION

To avoid damage to the monitor

and mount, always keep the arm in

a horizontal position while making

adjustments.

T-C

Increase Strength - If the arm

does not have enough movement,

turn the adjustment screws counter-

clockwise.

Adjusting Tension Decrease Strength - If the arm

raises up, turn the adjustment

screws clockwise until it holds the

monitor in a horizontal position.

Cable Management Covers

Adjustments

Lower Arm (B):

1. Slide cover forward to remove.

2. Place cables in cover.

3. Connect inner tabs to clips on Lower

Arm (B) arm to secure in place.

Upper Arm (A):

1. Pull tabs outward on lower portion of cover.

2. Pull upper tabs outward to fully remove cover.

3. Place cables in cover.

4. Re-install by snapping upper tabs in place,

then snap lower tabs on to fully secure.

Adjust monitor placement as desired. Allen Wrenches (T-B, T-C) can be stored in Cable Clamp

Clip (G) for future adjustments.

T-C T-B

360˚

+90˚

-45˚

360˚

180˚

LAST UPDATED: 11/29/2022

REV1

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

V I V O STAND-V101Q User manual

Brand: V I V O

Model: STAND-V101Q

Category: Flat panel desk mounts

Type: User manual

Download PDF

report

V I V O STAND-V101Q User manual

V I V O STAND-V101Q User manual

Related papers

Other documents