Page is loading ...
Gaming Counterbalance Desk Mount
Instruction Manual
MA07-12-US3.0
1.5~8kg
(3.3~17.6lbs)
RATED
VESA Size
75x75 mm
100x100 mm
Screen Weight
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
PRODUCT LINE GRAPH
02
WARNING!
300mm
75mm
100mm
115mm
75mm
100mm
115mm
189mm
7.4'' 8.19~11.06''
0.39~3.35''
7.36~19.17''
11.8''
0.39~3.35''
2.44''
4.53''
3.94''
2.95''
208~281mm 62mm
min10~max85mm
min187~max487mm
min10~max85mm
+90°
-45°
±90°
±90°
±180° ±180°
If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper
installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specied,
may cause damage or serious injury. We would not be liable for any damage or injury caused by improper
mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF
CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
Components
Hardware
PACKAGE CONTENTS
03
A (x1)
Arm
C (x1)
Bracket
D (x1)
Clamp
F (x1)
Long Bolt
G (x1)
Grommet Base
I (x1)
Security Screw
H (x1)
Support Plate
J (x6)
Screw
K(x1)
Wingnut
L(x1)
Base
M(x1)
Washer
N(x1)
Calathiform Gasket
O(x1)
Bolt
P(x1)
4mm Allen Key
Q(x1)
5mm Allen Key
E(x1)
Bracket Cover
B (x1)
VESA Plate
R(x1)
6mm Allen Key
Note: Not all hardware included will be used.
M-C (x4)
Spacer H10mm
M-A (x4)
M4x12mm
M-B (x4)
M4x25mm
STEP 1 Mount the Base to Bottom of the Arm
STEP 2 Clamp Installation OR Grommet Base Installation
04
OPTION A: Clamp Installation
Mount bracket (C) to the bottom of arm (A) using screws(J). Tighten the screws with
supplied 4mm Allen key (P).
p
J
C
A
A
L
M
N
O
Q
Mount the base(L) to the bottom of arm (A) using Washer(M), calathiform gasket(N) and Bolt(O).
Tighten (do not over tighten) the Bolt (O) securely with supplied 5mm Allen key (Q).
concave side of the
washer needs to be
faced to the Base (L)
You could also refer to the Video Guide about installation on our product page.
Warm Tips
Secure clamp (D) to upper two holes with
bolts (J) using 4mm Allen Key (P) for desks
with a thickness of 10-55mm.
Secure clamp (D) to lower two holes with
bolts (J) using 4mm Allen Key (P) for desks
with a thickness of 50-85mm.
Adjust the Mount to the Desktop
Thickness 10-55mm
Adjust the Mount to the Desktop
Thickness 50-85mm
Attach bracket cover (E)to bracket(C). Tighten the clamp to the desktop using the plastic knob
or by using 6mm Allen key (R).
05
R
OR
C
PJ
10-55mm
0.39-2.17"
1.97-3.35"
50-85mm
D
PJ
D
E
STEP 2 (Continued)
OPTION B: Grommet Base Installation
For grommet hole mounting, place long bolt(F) through the center of grommet base (G).
Mount grommet base to the bottom of arm (A) using screws(J). Tighten the screws with
supplied 4mm Allen key (P).
Run long bolt(F) through grommet hole in desktop. Secure it by using the support plate (H)
and Wingnut (K). Tighten Wingnut.
06
DESK DESK
Please do not move stand outside desk for safety!
G
J
F
P
K
H
A
F
DESK
DESK
ø 10~60mm
ø 0.39~2.36"
STEP 3 Attach the monitor to the arm
07
Monitor Monitor Monitor
monitor monitormonitor
OPTION A: Flat Back Monitor
OPTION B: Curved Back Monitor
Attach the VESA plate (B) to the back of monitor
and secure it by using a 6 mm Allen Key (R) to
tighten screws (M-A).
Do not tighten the screws excessively or your monitor
might be damaged.
Attach the VESA plate (B) to the back of monitor
and secure it by using a 6 mm Allen Key (R) to
tighten screws (M-B) along with spacers (M-C).
Do not tighten the screws excessively or your monitor
might be damaged.
B
M-A
R
B
M-B
M-C
R
08
Slide the monitor onto the head of swivel arm(A), install the security screw (I). Make
sure the security screw is tightened before you rotate the monitor.
Refer to below illustrations to
adjust tilting angle of your monitor.
A A
Problem:
If monitor face down
R
Solution:
1. Loosen the tilting bolt.
2. Hold the bottom of monitor with
one hand and adjust to determine
your desired tilt angle.
3. Retighten the tilting bolt
towards " " to x the angle.
I
09
STEP 4 Adjust the tension
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension spring in Arm (A) by using 6 mm Allen key (R).
Note:
It is normal for a bit noise when you adjust the spring tension.
R
A
After being attached to the arm, the monitor falls down
and can not stay at the desired height by itself.
Turn clockwise(“+”direction) to increase tension
until the monitor can stay at the desired Height by itself.
After being attached to the arm, the monitor rises up and
can not stay at the desired height by itself.
Turn counter-clockwise(“-”direction) to reduce tension until the
monitor can stay at the desired Height by itself.
WARNING
Please DO NOT loosen the screw.
For how many circles the screw should be turned, please refer to the table below.
Note2:
Circles (AT LEAST) 108643min 12
Monitor Weight 4.4lbs
(2kg) 6.6lbs
(3kg) 8.8lbs
(4kg) 11lbs
(5kg) 13.2lbs
(6kg) 15.4lbs
(7kg) 17.6lbs
(8kg)
10
STEP 5 Cable Management
Remove the bottom plastic covers from spring arm(A) as shown in diagram.
Run cables from monitor through the bottom of spring arm (A). Reattach plastic covers
as shown in diagram.
A
A
11
Adjust as Desired
Allen Key(P,Q) can be stored in Base Support Cover(E) for next time using.
+90°
-45°
±180°
±90°
±180°
±180°
Q
E
P
Note: To ensure stability, the tightness of the rotating axis has been
preset, so it would be kind of dicult to rotate the VESA plate.
Suggestion: Please attach the monitor rst, then hold the two sides
of it with both hands, and rotate vigorously.
If that doesn't work out, please do not hesitate to ask for our help.
• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals
(at least every three months).
CAUTION AND MAINTENANCE
/
