CREE LIGHTING VG Series Parking Structure Surface-Direct Installation guide

Brand: CREE LIGHTING

Model: VG Series Parking Structure Surface-Direct

Type: Installation guide

VG Series

LED Parking Luminaire

Surface Direct Mount (DM)

1 of 2 LPN00100X0005A0_D

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be

followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. To reduce the risk of electrical shock, turn o power supply before

installation or servicing.

2. This luminaire must be installed in accordance with the NEC or your local

electrical code. If you are not familiar with these codes and requirements,

consult a qualied electrician.

3. DO NOT lift luminaire by the supply cord.

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE

TO INSTALL:

LUMINAIRE INSTALLATION

STEP 1:

Using customer supplied hardware

attach mounting plate to ceiling with the

arrow on the underside of the Mounting

Plate directed parallel to vehicle traffic.

Ensure that the ceiling is capable of

supporting the weight of the luminaire.

See Figure 1 and 2.

STEP 2:

Bring luminaire up to Mounting Plate,

rotate luminaire until the arrow on the

inside of the Mounting Plate points to

the recessed area nearest to the latch

on the luminaire. See Figure 3.

STEP 3:

Attach luminaire to the Mounting Plate

by pressing up on the luminaire until the

slots on the Mounting Plate engage with

the clips on the luminaire and rotate

until latch locks securely. See Figure 4.

NOTE: May require extra pressure on

Mounting Plate to engage luminaire

clips into slots.

NOTE: If the Mounting Plate slots

become deformed during installation,

slightly reopen the slots back up using

a screwdriver to ensure proper install of

luminaire.

STEP 4:

Install a suitable Listed liquid tight cord

strain relief bushing in the customer

supplied junction box, and feed the

luminaire’s supply cord through it.

STEP 5:

Connect the cord to the supply wiring

per the “Electrical Connections”

section.

Slots

Luminaire

Clips

Latch

Arrow

Mounting Plate

Tamperproof

Screw

Latch

Underside View of

Mounting Plate

Arrow On Mounting Plate

Pointing Parrallel To

Traffic

Surface Direct

Mounting Plate

Luminaire

Supply Cord

2 of 2 LPN00100X0005A0_D

www.creelighting.com

subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree® and the Cree Lighting logo are

registered trademarks of Cree, Inc.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks is

under license. Other trademarks, service marks, and trade names are those of their respective owners. IOS is a registered

trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. Android

is a trademark of Google, Inc.

STEP 6:

Lightly pull on the luminaire to verify luminaire is securely mounted.

BLUETOOTH® TECHNOLOGY ENABLED MULTI-LEVEL SENSOR

(OPTIONAL)

The 8’ to 20’ sensor lens comes installed on the sensor on these luminaires.

A 20’ to 40’ sensor lens and aisle shroud is included in the hardware bag.

To change the lens, unscrew the existing lens, remove the shroud from the

replacement lens and screw the new lens back on to the sensor. If aisle

lighting is required, the shroud should be added to the appropriate lens.

For Sensor information please visit the Leviton website, www.Leviton.com

and search on ZLDxZ-xxx/OFDxZ-xxx.

Configuration is made using the Leviton Smart Sensor App from a

smartphone or other Bluetooth® enabled Android or iOS device. The Smart

Sensor App can be downloaded from either Goggle Play or Apple Store.

FIXTURE SERVICING AND MAINTENANCE

STEP 1:

If luminaire needs to be removed, fully loosen the tamperproof screw and

slide out the latch. Then, rotate luminaire to disengage from Mounting Plate.

See Figure 5.

STEP 2:

To re-install luminaire, engage and tighten the latch’s tamperproof screw

and follow Step 1-4 in “Luminaire Installation” section above.

Latch

Tamperproof

Screw

ELECTRICAL CONNECTIONS:

NOTE: Luminaires with BML sensor will have the dimming leads capped

off. Keep the dimming leads on these luminaires capped off.

STEP 1:

Make the following Electrical Connections :

a. For 120/277/347V connect the black fixture lead to the voltage

supply position of the junction box (Hot 1 for 208/240/480V

wiring).

b. For 120/277/347V Connect the white fixture lead to the neutral

supply position of the junction box (Hot 2 for 208/240/480V

wiring).

c. Connect the green or green/yellow ground lead to the green

wire position of the junction box.

d. If Dimming is an option; connect the violet dimming positive

lead to the supply dimming positive lead.

e. If Dimming is an option; connect the pink dimming negative

lead to the supply dimming negative lead.

LINE

OR HOT 1

GREEN

LINE-BLACK

GROUND-GREEN

NEUTRAL-WHITE

DIM (-) PINK

DIM (+) VIOLET

NEUTRAL

OR HOT 2

VIOLET

PINK

SUPPLY WIRING

(DIMMING OPTIONAL)

LUMINAIRE

JUNCTION

BOX

CREE LIGHTING VG Series Parking Structure Surface-Direct Installation guide

CREE LIGHTING VG Series Parking Structure Surface-Direct Installation guide

CREE LIGHTING VG Series Parking Structure Surface-Direct Installation guide

Related papers

Other documents