Page is loading ...
CPY500TM Series
LED Recessed Soffit Luminaire
Includes: CPY500TM Luminaires
1 of 4 LPN00843X0002A0_D
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the
following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant l’installation.
2. This luminaire must be installed in accordance with the NEC or your local electrical code. If you
are not familiar with these codes and requirements, consult a qualied electrician.
Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous n’êtes
pas familier avec ces codes et ces exigences, veuillez contacter un électricien qualié.
3. DO NOT lift luminaire by the power leads or cord.
4. This luminaire must be supported by main runners or other building structure that is capable of
supporting fixture weight.
5. Class 1 wiring methods only
6. Ensure the mounting surface is capable of supporting the weight of the luminaire.
7. 2L 120-277V and 4L 120-277V, 347-480V luminaires are listed as Type IC and are suitable for direct
contact with insulation.
8. 8L luminaires are listed as Type NON-IC and are thermally protected. Do not install insulation within
3 inches (76 mm) of xture sides or junction box or above xture in such a manner as to entrap
heat. Notice - Thermally protected luminaire. Blinking light may indicate insulation too close to
xture (or other condition causing overheating).
Ne pas mettre l’isolant a moins de 76 mm (3 po) de toute partie du luminaire. Avis - protection
thermique- clignotant lumière peut indiquer isolation trop près de l’appareil (ou autre condition
provoquant une surchaue).
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
TO INSTALL:
LUMINAIRE INSTALLATION:
NOTE: See Figure 1 for items included with
luminaire.
NOTE: Rough-in frame must be installed prior
to ceiling being finished or must be installed in
an accessible ceiling.
NOTE: See Figure 12 for dimensions of
luminaire and quick mount brackets.
STEP 1:
Cut a 14”x16” opening in the soffit. See Figure
3 for orientation of opening.
STEP 2:
Attach (2) quick-mount brackets to sides of the
rough-in frame using (4) supplied T20 torx pan
head screws. Torque screws to 23 in-lbs. See
Figure 2.
STEP 3:
Thread rigid conduit, bar stock, wire or
C-channel (supplied by others)through quick-
mount brackets at the sides of the rough-in
frame. See Figure 3.
STEP 4:
Attach mounting means to structure or other
adequate support.
STEP 5:
Adjust mounting height by loosening
adjustment nuts, then position brackets so
that the bottom of the rough-in frame is flush
with the bottom of the opening of the soffit.
See Figure 4.
1
Rough-in Frame
Luminaire Housing
Trim plate
2Quick-Mount Brackets
Rough-in Frame
Quick-Mount Brackets
Optional Occupancy
Sensor Housing
Optional Sensor Lens
Opening
NOTE: Hardware bag
included
34
Quick-Mount
Bracket
Rough-in Pan
Adjustment
Nut
Quick-Mount
Bracket
14"
Quick-Mount
Bracket
16"
2 of 4 LPN00843X0002A0_D
STEP 6:
Tighten adjustment nuts when frame is properly
adjusted.
STEP 7:
Hang luminaire housing onto rough-in frame using
hooks on the housing. See Figure 5.
STEP 8:
Remove the luminaire junction box cover shown in
Figure 6 and bring in appropriate power supply to the
wiring chamber using one of the knock-outs on the
cover.
NOTE: (2) knock-outs sized for use with ½” conduit
are present on luminaire junction box cover.
STEP 9:
Make wiring connections per the Electrical
Connections section.
STEP 10:
Replace cover on luminaire junction box.
STEP 11:
Rotate luminaire housing into place and secure with
2 retained screws. Torque screws to 23 in-lbs. See
Figure 7.
STEP 12:
For products with optional field adjustable dimming
refer to Field Adjustable Dimming section.
For products without field adjustable dimming
proceed to Step 13.
STEP 13:
For Products Without Occupancy Sensor:
• Secure trim plate to luminaire housing with
(4) supplied Phillips flat head screws. Torque
screws to 23 in-lbs. See Figure 8.
• Installation is now complete.
For Products With Occupancy Sensor:
• Unscrew occupancy sensor lens from occupancy
sensor. Retain lens.
• Secure trim plate to luminaire housing with
(4) supplied Phillips flat head screws. Torque
screws to 23 in-lbs. See Figure 8.
NOTE: Make sure occupancy sensor opening in
trim plate is positioned below occupancy sensor.
See Figure 1.
• Pass base of occupancy sensor lens through
opening in trim plate and screw lens to
occupancy sensor.
8
7
6
Luminaire
Junction Box
Cover
Flat Head Screws
Retained Screws
5
Hooks on luminaire
housing engaged with
frame
3 of 4 LPN00843X0002A0_D
11
10
9
Light Engine Screws
FIELD ADJUSTABLE DIMMING (OPTIONAL)
NOTE: This luminaire may be provided with a field adjustable
output control that allows the lumen output to be decreased from
the level that was set in the factory.
STEP 1:
The dimming control is visible inside the luminaire housing. See
Figure 11.
To access the control do the following:
• Disconnect the power to the luminaire.
• Loosen (4) retained T20 torx screws in corners of light
engine. See Figure 9.
• Allow light engine to swing down as shown in Figure 10.
STEP 2:
Establish the desired input power multiplier by referring to the
product dimming spec sheet and turn the switch to the correlating
position. For the half moon shaped dial the center of the flat side
should be turned to the desired setting. See Figure 11.
STEP 3:
After setting the switch, reattach the light engine to the luminaire
housing while ensuring that no wires are pinched. Torque (4) T20
torx screws to 23 in-lbs.
6.6" (167.5mm)
8.1" (205.5mm)
12
4 of 4 LPN00843X0002A0_D
www.creelighting.com
© 2023 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content is
subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree® and the Cree Lighting logo are
registered trademarks of Cree, Inc. CPY500TM is a trademark of Cree Lighting, A company of IDEAL INDUSTRIES.
ELECTRICAL CONNECTIONS- LUMINAIRE JUNCTION BOX
NOTE: Luminaire equipped with a 120V, 277V, 120-277V, or 347-480V
driver. Make sure voltage rating of luminaire is compatible with supply
voltage.
NOTE: For all circuits, use wire rated for the highest voltage involved.
NOTE: On luminaires with optional occupancy sensor, dimming is
controlled by the sensor and dimming leads are not present.
NOTE: Class 1 wiring methods only.
STEP 1:
Make the following Electrical Connections :
a. For 120/277/347V connect the black luminaire lead to the
voltage supply lead or Hot 1 (for 208/240/480V wiring).
b. For 120/277/347V connect the white luminaire lead to the
neutral supply lead or Hot 2 (208/240/480V wiring).
c. Connect the green or green/yellow ground lead to the supply
ground lead .
d. If Dimming is an option; connect the violet dimming positive
lead to the supply dimming positive lead.
e. If Dimming is an option; connect the pink dimming negative
lead to the supply dimming negative lead.
f. If Dimming leads are not used, insulate and cap the
dimming leads.
LINE
OR HOT 1
LINE-BLACK
NEUTRAL-WHITE
NEUTRAL
OR HOT 2
DIM (-)
DIM (+) VIOLET
PINK
SUPPLY WIRING
(DIMMING OPTIONAL)
LUMINAIRE
JUNCTION BOX
GROUND GREEN
FCC NOTICE
CAUTION: Changes or modifications not expressly approved could void
your authority to use this equipment.
This device complies with Part 15 of the FCC Rules. Operation to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the device is operated in a commercial environment.
This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this device in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
own expense.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device. In addition, this device complies with ICES-005 of the
Industry Canada (IC) Regulations.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
BLUETOOTH® TECHNOLOGY ENABLED MULTI-LEVEL SENSOR
(OPTIONAL)
The 8’ to 20’ sensor lens comes installed on the sensor on these
luminaires. A 20’ to 40’ sensor lens and aisle shroud is included in the
hardware bag. To change the lens, unscrew the existing lens, remove
the shroud from the replacement lens and screw the new lens back on
to the sensor. If aisle lighting is required, the shroud should be added to
the appropriate lens.
For Sensor information please visit the Leviton website, www.Leviton.
com and search on ZLDxZ-xxx/OFDxZ-xxx.
Configuration is made using the Leviton Smart Sensor App from a
smartphone or other Bluetooth® enabled Android or iOS device. The
Smart Sensor App can be downloaded from either Goggle Play or Apple
Store.
/
